Ultra-Low Power Wake Up Receiver For Medical Implant Communications Service Transceiver

This thesis explores the specific requirements and challenges for the design of a dedicated wake-up receiver for medical implant communication services equipped with a novel “uncertain-IF†architecture combined with a high – Q filtering MEMS resonator and a free running CMOS ring oscillator as the RF LO. The receiver prototype, implements an IBM 0.18μm mixed-signal 7ML RF CMOS technology and achieves a sensitivity of -62 dBm at 404MHz while consuming \u3c100 μW from a 1 V supply

Front End of a 900MHz RFID for Biological Sensing

This thesis presents the front end of a 900MHz passive RFID for biological sensing. The components blocks of the front end consist of power harvester, switch capacitor voltage regulator, phase lock loop and a modulator and demodulator. As the RFID is passive so the power resource is limited hence the main focus while implementing all the block was low power and high efficiency power conversion. All the individual block were optimized to provide maximum efficiency. For the harvester to achieve high efficiency and high output voltage a design approach is discussed by which the device sizes are optimized and the values of the matching network components are solved. The efficiency achieved with this approach is 34% while supplying 74�[email protected]. The switch capacitor voltage regulator would supply power to the digital core of the RFID, which will operate at subtheshold or moderate inversion. The switch capacitor implemented in this work is a adaptive voltage regulator, as I intend to use the dynamic supply voltage scaling technique to compensate for the reduction in reliability of performance of the circuit due to variation of VTH across process due to random doping effects and temperature in subthreshold.The phase lock loop (PLL) block in this front end provide the system clock synchronized with the base station to all the backend blocks like the digital controller, memory, and the analog to digital converter ADC and the switch capacitor voltage regulator. The PLL is a low power with jitter of 24nsec and is capable of clock data recovery from EPC gen 2 protocol format data and consumes 3�W of power Finally a ultra low power AM (amplitude modulation) demodulator is presented which is consumes only 100nW and is capable of demodulating a double-sideband amplitude modulated (DSB-AM) signal centered at 900MHz and the modulating frequency is 160KHz. The demodulator can demodulate signal having as low as -5dBm power and 50% modulation index. The modulation for transmitting signal is achieved by BPSK(back scatter phase shift keying).Electrical Engineerin

Analysis and design of UHF and millimetre wave radio frequency identification

Radio frequency identification (RFID) is an asymmetric radio protocol, where uplink communication (from transponder to reader) is implemented with backscattering modulation. The idea was first demonstrated in the 1940's. One of the first consumer applications of RFID was access control, and key cards based on an inductive near field coupling are widely used even today. The introduction of Schottky diodes to CMOS processes enabled passive RFID, i.e. transponders without a battery, at ultra high frequencies (UHF) with reasonable cost and read range in the end of 1990's. This has opened up new applications and inspired new research on RFID. This thesis studies the radio frequency (RF) components and general RF phenomena in RFID at UHF and millimetre waves. The theoretical analysis of the radio path reveals that the read range of a passive UHF system is ideally limited by the downlink, i.e. the power transfer from reader to the transponder. However, the architecture of the reader RF front end is critical, because the transmitted signal may couple a significant amount of noise to the receiver, overpowering the faint reflection from the transponder. In the thesis, two adaptive RF front ends are introduced to eliminate the noise coupling from the transmitter. One of the most critical problems with UHF RFID has been the detuning of transponder antennas on different mounting platforms. The detuning may significantly diminish the read range of the transponder, especially on metal surfaces. In this thesis, two backscattering-based measurement techniques for the transponder antennas are presented. The detuning effect has been studied using these measurement techniques, and a platform tolerant antenna is introduced. RFID at millimetre waves enables miniaturisation of the reader antenna, and widening the data bandwidth over short distances. This could be used to access wirelessly mass memories with wide data bandwidth. A semi-passive or active transponder could communicate, e.g., with automotive radars. The millimetre wave identification (MMID) has been theoretically studied and experimentally verified at 60 GHz

Advanced Radio Frequency Identification Design and Applications

Radio Frequency Identification (RFID) is a modern wireless data transmission and reception technique for applications including automatic identification, asset tracking and security surveillance. This book focuses on the advances in RFID tag antenna and ASIC design, novel chipless RFID tag design, security protocol enhancements along with some novel applications of RFID

Delay line based passive radio frequency identification tags

This work describes the concept, design, fabrication, and characterization of delay-based radio frequency identification (RFID) tags and RFID-based sensor tags, representing a novel RFID technology. The presented delay-based RFID concept is based on the LC-delay-line and transmission-delay-line based approaches. The proposed concept allows the realization of RFIDs and RFID-based sensor tags at any allowed radio frequency, with the limitation of realizing delay elements capable of producing required delays. The RFID configurations presented in this work are for operation at 915 MHz. Simulations are used to design and optimize components and devices that constitute the tags, and to integrate them to realize tags of different configuration. A set of fabrication processes has been developed for the realization of the tag. Characterization and field testing of these tags show that delay-based RFID approach can be used to make passive tags at ultra high frequency (UHF) and other allowed frequencies. Delay-based tags have the advantages of time domain operation, and the feasibility of complying with FCC regulations. However, size, need of isolators and circulator, and design constraints in producing higher number of bits are some of the concerns that need to be further addressed. In summary, this dissertation work presents a viable alternative RFID approach based on the delay line concept. The results obtained show great promise for further development and optimization of this approach for a wide range of commercial applications

MR4RF: MEM-device with impedance and their usage with impedance matching networks for passive RFID tags in the UHF

The passive RFID tag in the UHF has been employed in several different applications including, tracking, logistics, and as a sensing platform for the Internet of things (IoT). The tag is ideal for this industry due to its unique design. It harvests all of its energy from the environment, and is small, cheap, and requires little to no maintenance. However, there are two major issues limiting the potential of the passive RFID systems: the limited power harvested by the tag, and the high susceptibility to interference and coupling. In particular, dynamic environments render the traditionally fixed, RF impedance matching network ineffective. A novel design for a flexible Impedance-Switching Network (ISN) for passive RFID tags in the UHF is presented in this thesis. This novel approach can maximize power harvested by the tag. We propose two approaches to implementing the ISN. First, a more traditional design with a series of varactors is developed and studied. Each varactor is placed in parallel impedance lanes that are controlled via a feedback loop to maximize harvested power. A four-lane ISN is designed, tested, and tuned. The simulations and experiments demonstrate that ISN is capable of compensating for negative effect of mutual coupling in a ferromagnetic-reach environment. The second design employs a new material called a memristive switch that can replace the varactors in the ISN. State of a memristive switch is non-volatile and requires little energy to operate, thus making it ideal for passive RFID tags. We are the first to characterize the Co3O4 based memristive switch in UHF range. The results show that it can be employed as a varying capacitor in the RF front-end design. We propose three general configurations for the ISNs --Abstract, page iii

Design and Modelling of Passive UHF RFID Tags for Energy Efficient Liquid Level Detection Applications. A study of various techniques in the design, modelling, optimisation and deployment of RFID reader and passive UHF RFID tags to achieve effective performance for liquid sensing applications

Sewer and oil pipeline spillage issues have become major causes of pollution in urban and rural areas usually caused by blockages in the water storage and drainage system, and oil spillage of underground oil pipelines. An effective way of avoiding this problem will be by deploying some mechanism to monitor these installations at each point in time and reporting unusual liquid activity to the relevant authorities for prompt action to avoid a flooding or spillage occurrence. This research work presents a low cost energy efficient liquid level monitoring technique using Radio Frequency Identification Technology. Passive UHF RFID tags have been designed, modelled and optimized. A simple rectangular tag, the P-shaped tag and S-shaped tag with UHF band frequency of operation (850-950 MHz) has been designed and modelled. Detailed parametric analysis of the rectangular tag is made and the optimised design results analysed and presented in HFSS and Matlab. The optimised rectangular tag designs are then deployed as level sensors in a gully pot. Identical tags were deployed to detect 4 distinct levels in alternate positions and a few inches in seperation distance within the gully pot height (Low, Mid, High and Ultra high). The radiation characteristic of tag sensors in deployment as modelled on HFSS is observed to show consistent performance with application requirements. An in-manhole chamber antenna for an underground communication system is analysed, designed, deployed and measured. The antenna covers dual-band impedance bandwidths (i.e. 824 to 960 MHz, and 1710 to 2170 MHz). The results show that the antenna prototype exhibits sufficient impedance bandwidth, suitable radiation characteristics, and adequate gains for the required underground wireless sensor applications. Finally, a Linearly Shifted Quadrifilar Helical Antenna (LSQHA) designed using Genetic Algorithm optimisation technique for adoption as an RFID reader antenna is proposed and investigated. The new antenna confirms coverage of the RFID bandwidth 860-960 MHz with acceptable power gain of 13.1 dBi.Petroleum Technology Development Fund (PTDF) and National Space Research and Development Agency (NASRDA)

Wireless sensor system for infrastructure health monitoring

In this thesis, radio frequency identification (RFID)-based wireless sensor system for infrastructure health monitoring (IHM) is designed and developed. It includes mountable semi-passive tag antenna integrated sensors capable of measuring critical responses of infrastructure such as dynamic acceleration and strain. Furthermore, the system is capable of measuring structural displacement. One of the most important parts of this system is the relatively small, tunable, construction material mountable RFID tag antenna. The tag antenna is electronically integrated with the sensors. Leading to the process of developing tag antenna integrated sensors having satisfactory wireless performance (sensitivity and read range) when mounted on concrete and metal structural members, the electromagnetic performance of the tag antenna is analyzed and optimized using both numerical and experimental procedures. Subsequently, it is shown that both the simulation and the experimental measurement results are in good agreement. The semi-passive RFID-based system is implemented in a wireless IHM system with multiple sensor points to measure dynamic acceleration and strain. The developed system can determine the natural frequencies of infrastructure and identify any state changes of infrastructure by measuring natural frequency shifts. Enhancement of the spectral bandwidth of the system has been performed under the constraints of the RFID hardware. The influence of the orientation and shape of the structural members on wireless power flow in the vicinity of those members is also investigated with the RFID reader-tag antenna system in both simulation and experiments. The antenna system simulations with a full-scale structural member have shown that both the orientation and the shape of the structural member influence the wireless power flow towards and in the vicinity of the member, respectively. The measurement results of the conducted laboratory experiments using the RFID antenna system in passive mode have shown good agreement with simulation results. Furthermore, the system’s ability to measure structural displacement is also investigated by conducting phase angle of arrival measurements. It is shown that the system in its passive mode is capable of measuring small structural displacements within a short wireless distance. The benchmarking of the developed system with independent, commercial, wired and wireless measurement systems has confirmed the ability of the RFID-based system to measure dynamic acceleration and strain. Furthermore, it has confirmed the system’s ability to determine the natural frequency of an infrastructure accurately. Therefore, the developed system with wireless sensors that do not consume battery power in data transmission and with the capability of dynamic response measurement is highly applicable in IHM

Sensores passivos alimentados por transmissão de energia sem fios para aplicações de Internet das coisas

Nowadays, the Wireless Sensor Networks (WSNs) depend on the battery duration of the sensors and there is a renewed interest in creating a passive sensor network scheme in the area of Internet of Things (IoT) and space oriented WSN systems. The challenges for the future of radio communications have a twofold evolution, one being the low power consumption and, another, the adaptability and intelligent use of the available resources. Specially designed radios should be used to reduce power consumption, and adapt to the environment in a smart and e cient way. This thesis will focus on the development of passive sensors based on low power communication (backscatter) with Wireless Power Transfer (WPT) capabilities used in IoT applications. In that sense, several high order modulations for the communication will be explored and proposed in order to increase the data rate. Moreover, the sensors need to be small and cost e ective in order to be embedded in other technologies or devices. Consequently, the RF front-end of the sensors will be designed and implemented in Monolithic Microwave Integrated Circuit (MMIC).Atualmente, as redes de sensores sem fios dependem da duração da bateria e,deste modo, existe um interesse renovado em criar um esquema de rede de sensores passivos na área de internet das coisas e sistemas de redes de sensores sem fios relacionados com o espaço. Os desafios do futuro das comunicações de rádio têm uma dupla evolução, sendo um o baixo consumo de energia e, outro, a adaptação e o uso inteligente dos recursos disponíveis. Rádios diferentes dos convencionais devem ser usados para reduzir o consumo de energia e devem adaptar-se ao ambiente de forma inteligente e eficiente, de modo a que este use a menor quantidade de energia possível para estabelecer a comunicação. Esta tese incide sobre o desenvolvimento de sensores passivos baseados em comunicação de baixo consumo energético (backscatter) com recurso a transmissão de energia sem fios de modo a que possam ser usados em diferentes aplicações inseridas na internet das coisas. Nesse sentido, várias modulações de alta ordem para a comunicação backscatter serão exploradas e propostas com o objectivo de aumentar a taxa de transmissão de dados. Além disso, os sensores precisam de ser reduzidos em tamanho e económicos de modo a serem incorporados em outras tecnologias ou dispositivos. Consequentemente, o front-end de rádio frequência dos sensores será projetado e implementado em circuito integrado de microondas monolítico.Programa Doutoral em Engenharia Eletrotécnic