An Adaptive Controller Design for Flexible-joint Electrically-driven Robots With Consideration of Time-Varying Uncertainties

Almost all present control strategies for electrically-driven robots are under the rigid robot assumption. Few results can be found for the control of electrically driven robots with joint flexibility. This is because the presence of the joint flexibility greatly increases the complexity of the system dynamics. What is worse is when some system dynamics are not available and a good performance controller is required. In this paper, an adaptive design is proposed to this challenging problem. A backstepping-like procedure incorporating the model reference adaptive control is employed to circumvent the difficulty introduced by its cascade structure and various uncertainties. A Lyapunov-like analysis is used to justify the closed-loop stability and boundedness of internal signals. Moreover, the upper bounds of tracking errors in the transient state are also derived. Computer simulation results are presented to demonstrate the usefulness of the proposed scheme. Keywords: Adaptive control; Flexible-joint electrically-driven robot; FAT 2. Introduction Control of rigid robots has been well understood in recent years, but most of the schemes ignore the dynamics coming from electric motors and harmonic drivers that are widely implemented in the industrial robots. However, actuator dynamics constitute an important part of the complete robot dynamics, especially in the cases of high-velocity movement and highly varying loads[1],[2]. The main reason for using a reduced model is to simplify complexity of controller design. For each joint, consideration of the flexibility from the M. C. Chien was with the Department of Mechanical Engineering, National Taiwan University of Science and Technology. He is now with the Mechanical and Systems Research Laboratories, Industrial Technology Research Institute, No. 195, Sec. 4, Chung-Hsing Rd., Chutung, Hsinchu, 310, Taiwan, R.O.C. (e-mail: [email protected]). 2 A. C. Huang is with the Department of Mechanical Engineering, National Taiwan University of Science and Technology. No. 43, Keelung Rd., Sec. 4, Taipei, Taiwan, ROC. (Tel:+886-2-27376490, Fax: +886-2-37376460, E-mail: [email protected]). (A. C. Huang provides phone number because he is the corresponding author.

Control of flexible joint robotic manipulator using tuning functions design

The goal of this thesis is to design the controller for a single arm manipulator having a flexible joint for the tracking problem in two different cases. A controller is designed for a deterministic case wherein the plant parameters are assumed to be known while another is designed for an adaptive case where all the plant parameters are assumed to be unknown. In general the tracking problem is; given a smooth reference trajectory, the end effector has to track the reference while maintaining the stability. It is assumed that only the output of the manipulator, which is the link angle, is available for measurement. Also without loss of generality, the fast dynamics, that is the dynamics of the driver side of the system are neglected for the sake of simplicity; In the first case, the design procedure adopted is called observer backstepping. Since the states of the system are unavailable for measurement, an observer is designed that estimates the system states. These estimates are fed to the controller which in turn produces the control input to the system; The second case employs a design procedure called tuning functions design. In this case, since the plant parameters are unknown, the observer designed in case one cannot be used for determining the state estimates. For this purpose, parameter update laws and filters are designed for estimation of plant parameters. The filters employed are k-filters. The k-filters and the parameter update laws are given as input to the controller, which generates the control input to the system; For both cases, the mathematical models are simulated using Matlab/Simulink, and the results are verified

Discrete-time weight updates in neural-adaptive control

Abstract Typical neural-adaptive control approaches update neural-network weights as though they were adaptive parameters in a continuous-time adaptive control. However, requiring fast digital rates usually restricts the size of the neural network. In this paper we analyze a deltarule update for the weights, applied at a relatively slow digital rate. We show that digital weight update causes the neural network to estimate a discrete-time model of the system, assuming that state feedback is still applied in continuous time. A Lyapunov analysis shows uniformly ultimately bounded signals. Furthermore, slowing the update frequency and using the extra computational time to increase the size/accuracy of the neural network results in better performance. Experimental results achieving link tracking of a two-link flexible-joint robot verify the improved performance

Iterative Learning Control and its Applications

Robotic manipulators and Unmanned Aerial Vehicles (UAVs) have been used to execute some repeatable assignments, due to the advantage of safety, convenience, and flexibility. Iterative learning control (ILC) is an approach to eliminate some repeatable disturbance which may come from unknown parameters, dynamic uncertainties, or the surroundings. Therefore, this research aims to present two types of iterative learning controller, PD-type and adaptive-type, to implement on robotic manipulator and UAVs, which would complete the given repetitive missions and achieve the expected specifications. Meanwhile, a dead zone inverse model is proposed to solve the actuator dead zone problem. The traditional hierarchical control method for UAVs is adopted. The inner loop control performance is verified using Gimbal. The free flight experimental test is completed with the purpose of certifying the proposed out loop control stratagem. In addition, theoretical proof and simulation results are also presented to demonstrate the effectiveness of the proposed controllers

Smart Monitoring and Control in the Future Internet of Things

The Internet of Things (IoT) and related technologies have the promise of realizing pervasive and smart applications which, in turn, have the potential of improving the quality of life of people living in a connected world. According to the IoT vision, all things can cooperate amongst themselves and be managed from anywhere via the Internet, allowing tight integration between the physical and cyber worlds and thus improving efficiency, promoting usability, and opening up new application opportunities. Nowadays, IoT technologies have successfully been exploited in several domains, providing both social and economic benefits. The realization of the full potential of the next generation of the Internet of Things still needs further research efforts concerning, for instance, the identification of new architectures, methodologies, and infrastructures dealing with distributed and decentralized IoT systems; the integration of IoT with cognitive and social capabilities; the enhancement of the sensing–analysis–control cycle; the integration of consciousness and awareness in IoT environments; and the design of new algorithms and techniques for managing IoT big data. This Special Issue is devoted to advancements in technologies, methodologies, and applications for IoT, together with emerging standards and research topics which would lead to realization of the future Internet of Things

Tools for Nonlinear Control Systems Design

This is a brief statement of the research progress made on Grant NAG2-243 titled "Tools for Nonlinear Control Systems Design", which ran from 1983 till December 1996. The initial set of PIs on the grant were C. A. Desoer, E. L. Polak and myself (for 1983). From 1984 till 1991 Desoer and I were the Pls and finally I was the sole PI from 1991 till the end of 1996. The project has been an unusually longstanding and extremely fruitful partnership, with many technical exchanges, visits, workshops and new avenues of investigation begun on this grant. There were student visits, long term.visitors on the grant and many interesting joint projects. In this final report I will only give a cursory description of the technical work done on the grant, since there was a tradition of annual progress reports and a proposal for the succeeding year. These progress reports cum proposals are attached as Appendix A to this report. Appendix B consists of papers by me and my students as co-authors sorted chronologically. When there are multiple related versions of a paper, such as a conference version and journal version they are listed together. Appendix C consists of papers by Desoer and his students as well as 'solo' publications by other researchers supported on this grant similarly chronologically sorted

Entwurf eines Beobachterbasierten Robusten Nichtlinearen Reglers

Due to observers ability in the estimation of internal system states, observers play an important role in the field of control and monitoring of dynamical systems. In reality, using sensors to measure the desired system states may be costly and/or affects the reliability of technical systems. Besides, some signals are impractical or inaccessible to be measured and using of sensors leads to significant errors such as stochastic noise. The solution of using observers is well-known since 1964. Besides the estimation of system states, some observers are able to estimate unknown inputs affecting the system dynamics such as disturbance forces or torques. These features are helpful for supervision and fault diagnosis tasks by monitoring the sensors and system components or for advanced control purposes by realizing observer-based control for practical systems. Among the state and disturbance observers, Proportional-Integral-Observer (PIO) is highly appreciated because of its simple structure and design procedure. Furthermore, using sufficiently high gain PIO, a robust estimation of system states and unknown inputs can be achieved. Besides taking the advantages of high gain design, the disadvantages of large overshoot and strong influence from measurement noise (as typical drawbacks of high gain utilization) in the control and estimation performance can not be neglected. Recently, some researches have been done to overcome the disadvantages of high gain observers and to adaptively adjust the gain of observer based on the resulting actual performance. Considering the advantages and disadvantages of high gain PIO besides the recent developments, it is evident that there are still open problems and questions to be solved in the area of optimal design of PIO and robust nonlinear control approaches based on PIO. On the other hand, the PI-Observer can be used in combination with linear/nonlinear control approaches (due to its simple structure and capability to estimate the system states and disturbances) to improve the performance and robustness of the closed-loop control results. Therefore, this thesis focuses on development and improvement of high gain Proportional-Integral-Observer as well as utilization of this observer in combination with well-known robust control approaches for possible general application in nonlinear systems. The Modified Advanced PIO (MAPIO) is introduced in this work as the extended version of Advanced PIO (APIO) to tune the gain of PIO according to the current situation. A cost function is defined so that the estimation performance and the related energy can be evaluated. Comparison between advanced observer design approaches has been done in the task of reconstructing the nonlinear characteristics and estimating the external inputs (contact forces) acting to elastic mechanical structures. Simulation results in open-loop and closed-loop cases verified that the performance of MAPIO in the task of unknown input estimation is more robust to different levels of measurement noise in comparison to previous methods e.g. APIO and standard high/low gain PIO. Furthermore, a new gain design approach of Proportional-Integral-Observer is proposed to overcome the disadvantages of high gain PIO and to realize the estimation of fast dynamical behaviors like unknown impact force. The dynamics of this force input is assumed as unknown. The idea of funnel control is taking into consideration to design the PIO gain. The important advantage of the proposed approach compared to previously published PIO gain design is the self-adjustment of observer gains according to the actual estimation situation inside the predefined funnel area. In this thesis it is shown that the proposed funnel PI-Observer algorithm allows adaptive PIO gain calculation, being able to be situatively adjusted even in the presence of measurement noise. Stability proof of funnel PI-Observer is investigated according to the switching observer condition and Lyapunov theory. The effectiveness of the proposed method is evaluated by simulation and experimental results using an elastic beam test rig. Furthermore, a nonlinear MIMO mechanical system is used to verify the effectiveness of the proposed method in the closed-loop context. Additionally, this thesis provides two new PI-Observer-based robust controllers as PIO-based sliding mode control and PIO-based backstepping control to improve the position tracking performance of a hydraulic differential cylinder system in the presence of uncertainties e.g. modeling errors, disturbances, and measurement noise. To use the linear PIO for estimation of system states and unknown inputs, the input-output feedback linearization approach is used to linearize the nonlinear model of hydraulic differential cylinder system. Thereupon the result of state and unknown input estimation is integrated into the structure of robust control design (here SMC and backstepping control) to eliminate the effects of uncertainties and disturbances. The introduced PIO-based robust controllers guarantee the ultimate boundness of the tracking error in the presence of uncertainties. The closed-loop stability is proved using Lyapunov theory in both cases. The proposed methods are experimentally validated and the results are compared with the standard SMC and industrial standard approach P-Controller in the presence of measurement noise, model uncertainties, and external disturbances. A general comparison of SMC and backstepping control approaches is provided in the last part of this work.Die Regelung und Überwachung dynamischer Systeme kann voraussetzen, dass Informationen über interne Systemzustände bekannt sind. Die Verwendung von Sensoren zur Erfassung aller Systemzustände kann erhöhte Kosten zur Folge haben und die Systemzuverlässigkeit negativ beeinflussen. Weitere Probleme ergeben sich dadurch, dass ggf. nicht jeder Systemzustand sensorisch erfasst werden kann. Der Beobachter erlaubt die Rekonstruktion aller Systemzustände auf Grundlage weniger Messungen. Neben Systemzuständen können externe Eingangsgrößen wie Reibmomente und Störungen geschätzt werden. Als Konsequenz ermöglicht der Beobachter eine gegenüber Störungen robuste Regelung und Fehlerdiagnose technischer Systeme. Der Proportional-Integral-Observer (PIO) kann mittels bestehender Entwurfsverfahren einfach implementiert werden. Durch Anpassen der Rückkopplungsmatrix eignet sich der PIO zur kombinierten Schätzung von Zuständen und unbekannten Eingangsgrößen. In diesem Zusammenhang spielt die Wahl einer betragsmäßig großen Rückkopplungsverstärkungsmatrix, als sogenannter High Gain Ansatz, eine entscheidende Rolle. Weiterhin hängt die Performance des PIO von der unbekannten Charakteristik der zu schätzenden Eingangsgröße ab. Diese Arbeit befasst sich mit der Entwicklung optimierter Entwurfsverfahren für den Proportional-Integral-Observer und der Entwicklung und Anwendung beobachterbasierter Konzepte zur robusten Regelung nichtlinearer Systeme. In dieser Arbeit wird der modifizierte Advanced PIO (MAPIO) als erweiterte Version des Advanced PIO (APIO) eingeführt. Der Schätzfehler von MAPIO wird über ein Gütefunktional abgebildet. Das Gütefunktional wird durch Anpassung der Rückkopplungsverstärkungsmatrix an die Charakteristik der unbekannten Eingangsgröße minimiert. Die Performance der modifizierten Beobachterentwurfsansätze wird anhand eines praktischen Beispiels bewertet. Geschätzt wird eine unbekannte Kontaktkraft mit nichtlinearer Charakteristik, die auf ein mechanisches System wirkt. Anhand eines Simulationsbeispiels im offenen und geschlossenen Regelkreis wird die Performance von MAPIO gegenüber vorherigen Verfahren APIO und PIO verifiziert. Basierend auf der Idee des Funnel Reglers wird ein neuartiges Entwurfskonzept für den Proportional-Integral-Observer vorgestellt. Die Nachteile des PIO-Konzeptes mit hohem Verstärkungsfaktor können überwunden werden und Schätzungen schneller dynamischer Verhaltensweisen lassen sich realisieren. Der Vorteil der neuartigen Funnel PIO Methode ist, dass der Schätzfehler in einem definierten Bereich, der sogenannten Funnel-Area, verbleibt. In dieser Arbeit wird gezeigt, dass der vorgeschlagene Funnel PIO Algorithmus eine adaptive PIO Verstärkungsberechnung ermöglicht, die auch in Gegenwart von Messrauschen situativ eingestellt werden kann. Der Stabilitätsnachweis von Funnel PIO wird mittels der Lyapunov Theorie untersucht. Die Wirksamkeit der vorgeschlagenen Methode wird durch Simulation und experimentelle Ergebnisse validiert. Eine auf einen elastischen Balken wirkende äußere Kraft mit nichtlinearer Charakteristik wird geschätzt. Ein nichtlineares MIMO System wird verwendet, um die Wirksamkeit der vorgeschlagenen Methode im geschlossenen Regelkreis zu verifizieren. In dieser Arbeit werden zwei neue PI-Observer basierte robuste Regelungen (PIO-basierte Sliding Mode und PIO-basierte Backstepping Regelung) vorgestellt. Die Positionsregelung eines hydraulischen Differentialzylinders in Gegenwart von Modellunsicherheiten, Störungen und Messrauschen wird untersucht. Zur Anwendung der PIO-basierten Störgrößenschätzung wird eine Ein-/Ausgangs-Linearisierung des nichtlinearen Modells vorgenommen. Die Stabilität des geschlossenen Regelkreises wird in beiden Fällen mit der Lyapunov Theorie bewiesen. Die vorgeschlagenen Methoden werden experimentell validiert und die Ergebnisse werden mit dem Standard Sliding Mode Regler und einem P-Regler in Gegenwart von Messrauschen, Modellunsicherheiten und externen Störungen verglichen

Game-Theoretic Safety Assurance for Human-Centered Robotic Systems

In order for autonomous systems like robots, drones, and self-driving cars to be reliably introduced into our society, they must have the ability to actively account for safety during their operation. While safety analysis has traditionally been conducted offline for controlled environments like cages on factory floors, the much higher complexity of open, human-populated spaces like our homes, cities, and roads makes it unviable to rely on common design-time assumptions, since these may be violated once the system is deployed. Instead, the next generation of robotic technologies will need to reason about safety online, constructing high-confidence assurances informed by ongoing observations of the environment and other agents, in spite of models of them being necessarily fallible.This dissertation aims to lay down the necessary foundations to enable autonomous systems to ensure their own safety in complex, changing, and uncertain environments, by explicitly reasoning about the gap between their models and the real world. It first introduces a suite of novel robust optimal control formulations and algorithmic tools that permit tractable safety analysis in time-varying, multi-agent systems, as well as safe real-time robotic navigation in partially unknown environments; these approaches are demonstrated on large-scale unmanned air traffic simulation and physical quadrotor platforms. After this, it draws on Bayesian machine learning methods to translate model-based guarantees into high-confidence assurances, monitoring the reliability of predictive models in light of changing evidence about the physical system and surrounding agents. This principle is first applied to a general safety framework allowing the use of learning-based control (e.g. reinforcement learning) for safety-critical robotic systems such as drones, and then combined with insights from cognitive science and dynamic game theory to enable safe human-centered navigation and interaction; these techniques are showcased on physical quadrotors—flying in unmodeled wind and among human pedestrians—and simulated highway driving. The dissertation ends with a discussion of challenges and opportunities ahead, including the bridging of safety analysis and reinforcement learning and the need to ``close the loop'' around learning and adaptation in order to deploy increasingly advanced autonomous systems with confidence