A Markovian jump system approach for the estimation and adaptive diagnosis of decreased power generation in wind farms

In this study, a Markovian jump model of the power generation system of a wind turbine is proposed and the authors present a closed-loop model-based observer to estimate the faults related to energy losses. The observer is designed through an H∞-based optimisation problem that optimally fixes the trade-off between the observer fault sensitivity and robustness. The fault estimates are then used in data-based decision mechanisms for achieving fault detection and isolation. The performance of the strategy is then ameliorated in a wind farm (WF) level scheme that uses a bank of the aforementioned observers and decision mechanisms. Finally, the proposed approach is tested using a well-known benchmark in the context of WF fault diagnosis

Predictive control approaches to fault tolerant control of wind turbines

This thesis focuses on active fault tolerant control (AFTC) of wind turbine systems. Faults in wind turbine systems can be in the form of sensor faults, actuator faults, or component faults. These faults can occur in different locations, such as the wind speed sensor, the generator system, drive train system or pitch system. In this thesis, some AFTC schemes are proposed for wind turbine faults in the above locations. Model predictive control (MPC) is used in these schemes to design the wind turbine controller such that system constraints and dual control goals of the wind turbine are considered. In order to deal with the nonlinearity in the turbine model, MPC is combined with Takagi-Sugeno (T-S) fuzzy modelling. Different fault diagnosis methods are also proposed in different AFTC schemes to isolate or estimate wind turbine faults.The main contributions of the thesis are summarized as follows:A new effective wind speed (EWS) estimation method via least-squares support vector machines (LSSVM) is proposed. Measurements from the wind turbine rotor speed sensor and the generator speed sensor are utilized by LSSVM to estimate the EWS. Following the EWS estimation, a wind speed sensor fault isolation scheme via LSSVM is proposed.A robust predictive controller is designed to consider the EWS estimation error. This predictive controller serves as the baseline controller for the wind turbine system operating in the region below rated wind speed.T-S fuzzy MPC combining MPC and T-S fuzzy modelling is proposed to design the wind turbine controller. MPC can deal with wind turbine system constraints externally. On the other hand, T-S fuzzy modelling can approximate the nonlinear wind turbine system with a linear time varying (LTV) model such that controller design can be based on this LTV model. Therefore, the advantages of MPC and T-S fuzzy modelling are both preserved in the proposed T-S fuzzy MPC.A T-S fuzzy observer, based on online eigenvalue assignment, is proposed as the sensor fault isolation scheme for the wind turbine system. In this approach, the fuzzy observer is proposed to deal with the nonlinearity in the wind turbine system and estimate system states. Furthermore, the residual signal generated from this fuzzy observer is used to isolate the faulty sensor.A sensor fault diagnosis strategy utilizing both analytical and hardware redundancies is proposed for wind turbine systems. This approach is proposed due to the fact that in the real application scenario, both analytical and hardware redundancies of wind turbines are available for designing AFTC systems.An actuator fault estimation method based on moving horizon estimation (MHE) is proposed for wind turbine systems. The estimated fault by MHE is then compensated by a T-S fuzzy predictive controller. The fault estimation unit and the T-S fuzzy predictive controller are combined to form an AFTC scheme for wind turbine actuator faults

A review of convex approaches for control, observation and safety of linear parameter varying and Takagi-Sugeno systems

This paper provides a review about the concept of convex systems based on Takagi-Sugeno, linear parameter varying (LPV) and quasi-LPV modeling. These paradigms are capable of hiding the nonlinearities by means of an equivalent description which uses a set of linear models interpolated by appropriately defined weighing functions. Convex systems have become very popular since they allow applying extended linear techniques based on linear matrix inequalities (LMIs) to complex nonlinear systems. This survey aims at providing the reader with a significant overview of the existing LMI-based techniques for convex systems in the fields of control, observation and safety. Firstly, a detailed review of stability, feedback, tracking and model predictive control (MPC) convex controllers is considered. Secondly, the problem of state estimation is addressed through the design of proportional, proportional-integral, unknown input and descriptor observers. Finally, safety of convex systems is discussed by describing popular techniques for fault diagnosis and fault tolerant control (FTC).Peer ReviewedPostprint (published version

Changes of Water/Ice Morphological, Thermodynamic, and Mechanical Parameters During the Freezing Process

To reduce ice adhesion hazards, optimize or develop the anti/de-icing methods, it is necessary to understand the change of freezing parameters during the freezing process, such as thermodynamic, morphological, and mechanical parameters. The present study investigates the freezing characteristics by purpose-built devices to describe the freezing process quantitatively. Morphological parameters were calculated the reverse engineering. The results showed that the inner temperature and morphology of water droplet were obviously changed, and the freezing process could be mainly divided into three stages: initial and spreading, freezing, and steady-state. Moreover, an experimental apparatus that measured the phase swelling force was built on investigating the freezing process of water from the mechanical aspect. It was found that the swelling force generated from the freezing process of 2473 mm3 water could reach 46.38 N. The generation process of swelling force could also be separated into three stages: non-expansive stage, increasing stage, and stable stage. The formation stage of swelling force was similar to that of ice. Combining the measured expansion force with the calculated freezing parameters based on the observed test, the freezing process of water could be better understood. The study would help researchers and engineers understand the freezing process and provide some freezing characteristics parameters for the anti/de-icing research

Multiobjective performance-based designs in fault estimation and isolation for discrete-time systems and its application to wind turbines

In this work, we develop a performance-based design of model-based observes and statistical-based decision mechanisms for achieving fault estimation and fault isolation in systems affected by unknown inputs and stochastic noises. First, through semidefinite programming, we design the observers considering different estimation performance indices as the covariance of the estimation errors, the fault tracking delays and the degree of decoupling from unknown inputs and from faults in other channels. Second, we perform a co-design of the observers and decision mechanisms for satisfying certain trade-off between different isolation performance indices: the false isolation rates, the isolation times and the minimum size of the isolable faults. Finally, we extend these results to a scheme based on a bank of observers for the case where multiple faults affect the system and isolability conditions are not verified. To show the effectiveness of the results, we apply these design strategies to a well-known benchmark of wind turbines which considers multiple faults and has explicit requirements over isolation times and false isolation rates

Maintenance Management of Wind Turbines

“Maintenance Management of Wind Turbines” considers the main concepts and the state-of-the-art, as well as advances and case studies on this topic. Maintenance is a critical variable in industry in order to reach competitiveness. It is the most important variable, together with operations, in the wind energy industry. Therefore, the correct management of corrective, predictive and preventive politics in any wind turbine is required. The content also considers original research works that focus on content that is complementary to other sub-disciplines, such as economics, finance, marketing, decision and risk analysis, engineering, etc., in the maintenance management of wind turbines. This book focuses on real case studies. These case studies concern topics such as failure detection and diagnosis, fault trees and subdisciplines (e.g., FMECA, FMEA, etc.) Most of them link these topics with financial, schedule, resources, downtimes, etc., in order to increase productivity, profitability, maintainability, reliability, safety, availability, and reduce costs and downtime, etc., in a wind turbine. Advances in mathematics, models, computational techniques, dynamic analysis, etc., are employed in analytics in maintenance management in this book. Finally, the book considers computational techniques, dynamic analysis, probabilistic methods, and mathematical optimization techniques that are expertly blended to support the analysis of multi-criteria decision-making problems with defined constraints and requirements

Aeronautical engineering: A continuing bibliography with indexes (supplement 247)

This bibliography lists 437 reports, articles, and other documents introduced into the NASA scientific and technical information system in December, 1989. Subject coverage includes: design, construction and testing of aircraft and aircraft engines; aircraft components, equipment and systems; ground support systems; and theoretical and applied aspects of aerodynamics and general fluid dynamics