A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

Review of Injected Oscillators

Oscillators are critical components in electrical and electronic engineering and other engineering and sciences. Oscillators are classified as free-running oscillators and injected oscillators. This chapter describes the background necessary for the analysis and design of injected oscillators. When an oscillator is injected by an external periodic signal mentioned as an injection signal, it is called an injected oscillator. Consequently, two phenomena occur in the injected oscillators: (I) pulling phenomena and (II) locking phenomena. For locking phenomena, the oscillation frequency of the injection signal must be near free-running oscillation frequency or its sub-/super-harmonics. Due to these phenomena are nonlinear phenomena, it is tough to achieve the exact equation or closed-form equation of them. Therefore, researchers are scrutinizing them by different analytical and numerical methods for accomplishing an exact inside view of their performances. In this chapter, injected oscillators are investigated in two main subjects: first, analytical methods on locking and pulling phenomena are reviewed, and second, applications of injected oscillators are reviewed such as injection-locked frequency dividers at the latter. Furthermore, methods of enhancing the locking range are introduced

Architectures and Circuits Leveraging Injection-Locked Oscillators for Ultra-Low Voltage Clock Synthesis and Reference-less Receivers for Dense Chip-to-Chip Communications

High performance computing is critical for the needs of scientific discovery and economic competitiveness. An extreme-scale computing system at 1000x the performance of today’s petaflop machines will exhibit massive parallelism on multiple vertical fronts, from thousands of computational units on a single processor to thousands of processors in a single data center. To facilitate such a massively-parallel extreme-scale computing, a key challenge is power. The challenge is not power associated with base computation but rather the problem of transporting data from one chip to another at high enough rates. This thesis presents architectures and techniques to achieve low power and area footprint while achieving high data rates in a dense very-short reach (VSR) chip-to-chip (C2C) communication network. High-speed serial communication operating at ultra-low supplies improves the energy-efficiency and lowers the power envelop of a system doing an exaflop of loops. One focus area of this thesis is clock synthesis for such energy-efficient interconnect applications operating at high speeds and ultra-low supplies. A sub-integer clockfrequency synthesizer is presented that incorporates a multi-phase injection-locked ring-oscillator-based prescaler for operation at an ultra-low supply voltage of 0.5V, phase-switching based programmable division for sub-integer clock-frequency synthesis, and automatic calibration to ensure injection lock. A record speed of 9GHz has been demonstrated at 0.5V in 45nm SOI CMOS. It consumes 3.5mW of power at 9.12GHz and 0.052 of area, while showing an output phase noise of -100dBc/Hz at 1MHz offset and RMS jitter of 325fs; it achieves a net of -186.5 in a 45-nm SOI CMOS process. This thesis also describes a receiver with a reference-less clocking architecture for high-density VSR-C2C links. This architecture simplifies clock-tree planning in dense extreme-scaling computing environments and has high-bandwidth CDR to enable SSC for suppressing EMI and to mitigate TX jitter requirements. It features clock-less DFE and a high-bandwidth CDR based on master-slave ILOs for phase generation/rotation. The RX is implemented in 14nm CMOS and characterized at 19Gb/s. It is 1.5x faster that previous reference-less embedded-oscillator based designs with greater than 100MHz jitter tolerance bandwidth and recovers error-free data over VSR-C2C channels. It achieves a power-efficiency of 2.9pJ/b while recovering error-free data (BER 200MHz and the INL of the ILO-based phase-rotator (32- Steps/UI) is <1-LSB. Lastly, this thesis develops a time-domain delay-based modeling of injection locking to describe injection-locking phenomena in nonharmonic oscillators. The model is used to predict the locking bandwidth, and the locking dynamics of the locked oscillator. The model predictions are verified against simulations and measurements of a four-stage differential ring oscillator. The model is further used to predict the injection-locking behavior of a single-ended CMOS inverter based ring oscillator, the lock range of a multi-phase injection-locked ring-oscillator-based prescaler, as well as the dynamics of tracking injection phase perturbations in injection-locked masterslave oscillators; demonstrating its versatility in application to any nonharmonic oscillator

Design of CMOS integrated frequency synthesizers for ultra-wideband wireless communications systems

Ultra¬wide band (UWB) system is a breakthrough in wireless communication, as it provides data rate one order higher than existing ones. This dissertation focuses on the design of CMOS integrated frequency synthesizer and its building blocks used in UWB system. A mixer¬based frequency synthesizer architecture is proposed to satisfy the agile frequency hopping requirement, which is no more than 9.5 ns, three orders faster than conventional phase¬locked loop (PLL)¬based synthesizers. Harmonic cancela¬tion technique is extended and applied to suppress the undesired harmonic mixing components. Simulation shows that sidebands at 2.4 GHz and 5 GHz are below 36 dBc from carrier. The frequency synthesizer contains a novel quadrature VCO based on the capacitive source degeneration structure. The QVCO tackles the jeopardous ambiguity of the oscillation frequency in conventional QVCOs. Measurement shows that the 5¬GHz CSD¬QVCO in 0.18 µm CMOS technology draws 5.2 mA current from a 1.2 V power supply. Its phase noise is ¬120 dBc at 3 MHz offset. Compared with existing phase shift LC QVCOs, the proposed CSD¬QVCO presents better phase noise and power efficiency. Finally, a novel injection locking frequency divider (ILFD) is presented. Im¬plemented with three stages in 0.18 µm CMOS technology, the ILFD draws 3¬mA current from a 1.8¬V power supply. It achieves multiple large division ratios as 6, 12, and 18 with all locking ranges greater than 1.7 GHz and injection frequency up to 11 GHz. Compared with other published ILFDs, the proposed ILFD achieves the largest division ratio with satisfactory locking range

Millimeter-wave Communication and Radar Sensing — Opportunities, Challenges, and Solutions

With the development of communication and radar sensing technology, people are able to seek for a more convenient life and better experiences. The fifth generation (5G) mobile network provides high speed communication and internet services with a data rate up to several gigabit per second (Gbps). In addition, 5G offers great opportunities of emerging applications, for example, manufacture automation with the help of precise wireless sensing. For future communication and sensing systems, increasing capacity and accuracy is desired, which can be realized at millimeter-wave spectrum from 30 GHz to 300 GHz with several tens of GHz available bandwidth. Wavelength reduces at higher frequency, this implies more compact transceivers and antennas, and high sensing accuracy and imaging resolution. Challenges arise with these application opportunities when it comes to realizing prototype or demonstrators in practice. This thesis proposes some of the solutions addressing such challenges in a laboratory environment.High data rate millimeter-wave transmission experiments have been demonstrated with the help of advanced instrumentations. These demonstrations show the potential of transceiver chipsets. On the other hand, the real-time communication demonstrations are limited to either low modulation order signals or low symbol rate transmissions. The reason for that is the lack of commercially available high-speed analog-to-digital converters (ADCs); therefore, conventional digital synchronization methods are difficult to implement in real-time systems at very high data rates. In this thesis, two synchronous baseband receivers are proposed with carrier recovery subsystems which only require low-speed ADCs [A][B].Besides synchronization, high-frequency signal generation is also a challenge in millimeter-wave communications. The frequency divider is a critical component of a millimeter-wave frequency synthesizer. Having both wide locking range and high working frequencies is a challenge. In this thesis, a tunable delay gated ring oscillator topology is proposed for dual-mode operation and bandwidth extension [C]. Millimeter-wave radar offers advantages for high accuracy sensing. Traditional millimeter-wave radar with frequency-modulated continuous-wave (FMCW), or continuous-wave (CW), all have their disadvantages. Typically, the FMCW radar cannot share the spectrum with other FMCW radars.\ua0 With limited bandwidth, the number of FMCW radars that could coexist in the same area is limited. CW radars have a limited ambiguous distance of a wavelength. In this thesis, a phase-modulated radar with micrometer accuracy is presented [D]. It is applicable in a multi-radar scenario without occupying more bandwidth, and its ambiguous distance is also much larger than the CW radar. Orthogonal frequency-division multiplexing (OFDM) radar has similar properties. However, its traditional fast calculation method, fast Fourier transform (FFT), limits its measurement accuracy. In this thesis, an accuracy enhancement technique is introduced to increase the measurement accuracy up to the micrometer level [E]

Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers

There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular. Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process. CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers. A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band. The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided

A Fully Integrated Multi-Band Multi-Output Synthesizer with Wide-Locking-Range 1/3 Injection Locked Divider Utilizing Self-Injection Technique for Multi-Band Microwave Systems

This dissertation reports the development of a new multi-band multi-output synthesizer, 1/2 dual-injection locked divider, 1/3 injection-locked divider with phase-tuning, and 1/3 injection-locked divider with self-injection using 0.18-micrometer CMOS technology. The synthesizer is used for a multi-band multi-polarization radar system operating in the K- and Ka-band. The synthesizer is a fully integrated concurrent tri-band, tri-output phase-locked loop (PLL) with divide-by-3 injection locked frequency divider (ILFD). A new locking mechanism for the ILFD based on the gain control of the feedback amplifier is utilized to enable tunable and enhanced locking range which facilitates the attainment of stable locking states. The PLL has three concurrent multiband outputs: 3.47-4.313 GHz, 6.94-8.626 GHz and 19.44-21.42-GHz. High second-order harmonic suppression of 62.2 dBc is achieved without using a filter through optimization of the balance between the differential outputs. The proposed technique enables the use of an integer-N architecture for multi-band and microwave systems, while maintaining the benefit of the integer-N architecture; an optimal performance in area and power consumption. The 1/2 dual-ILFD with wide locking range and low-power consumption is analyzed and designed together with a divide-by-2 current mode logic (CML) divider. The 1/2 dual-ILFD enhances the locking range with low-power consumption through optimized load quality factor (QL) and output current amplitude (iOSC) simultaneously. The 1/2 dual-ILFD achieves a locking range of 692 MHz between 7.512 and 8.204 GHz. The new 1/2 dual-ILFD is especially attractive for microwave phase-locked loops and frequency synthesizers requiring low power and wide locking range. The 3.5-GHz divide-by-3 (1/3) ILFD consists of an internal 10.5-GHz Voltage Controlled Oscillator (VCO) functioning as an injection source, 1/3 ILFD core, and output inverter buffer. A phase tuner implemented on an asymmetric inductor is proposed to increase the locking range. The other divide-by-3 ILFD utilizes self-injection technique. The self-injection technique substantially enhances the locking range and phase noise, and reduces the minimum power of the injection signal needed for the 1/3 ILFD. The locking range is increased by 47.8 % and the phase noise is reduced by 14.77 dBc/Hz at 1-MHz offset

Design of Frequency divider with voltage vontrolled oscillator for 60 GHz low power phase-locked loops in 65 nm RF CMOS

Increasing memory capacity in mobile devices, is driving the need of high-data rates equipment. The 7 GHz band around 60 GHz provides the opportunity for multi-gigabit/sec wireless communication. It is a real opportunity for developing next generation of High-Definition (HD) devices. In the last two decades there was a great proliferation of Voltage Controlled Oscillator (VCO) and Frequency Divider (FD) topologies in RF ICs on silicon, but reaching high performance VCOs and FDs operating at 60 GHz is in today's technology a great challenge. A key reason is the inaccuracy of CMOS active and passive device models at mm-W. Three critical issues still constitute research objectives at 60 GHz in CMOS: generation of the Local Oscillator (LO) signal (1), division of the LO signal for the Phase-Locked Loop (PLL) closed loop (2) and distribution of the LO signal (3). In this Thesis, all those three critical issues are addressed and experimentally faced-up: a divide-by-2 FD for a PLL of a direct-conversion transceiver operating at mm-W frequencies in 65 nm RF CMOS technology has been designed. Critical issues such as Process, Voltage and Temperature (PVT) variations, Electromagnetic (EM) simulations and power consumption are addressed to select and design a FD with high frequency dividing range. A 60 GHz VCO is co-designed and integrated in the same die, in order to provide the FD with mm-W input signal. VCOs and FDs play critical roles in the PLL. Both of them constitute the PLL core components and they would need co-design, having a big impact in the overall performance especially because they work at the highest frequency in the PLL. Injection Locking FD (ILFD) has been chosen as the optimum FD topology to be inserted in the control loop of mm-W PLL for direct-conversion transceiver, due to the high speed requirements and the power consumption constraint. The drawback of such topology is the limited bandwidth, resulting in narrow Locking Range (LR) for WirelessHDTM applications considering the impact of PVT variations. A simulation methodology is presented in order to analyze the ILFD locking state, proposing a first divide-by-2 ILFD design with continuous tuning. In order to design a wide LR, low power consumption ILFD, the impacts of various alternatives of low/high Q tank and injection scheme are deeply analysed, since the ILFD locking range depends on the Q of the tank and injection efficiency. The proposed 3-bit dual-mixing 60 GHz divide-by-2 LC-ILFD is designed with an accumulation of switching varactors binary scaled to compensate PVT variations. It is integrated in the same die with a 4-bit 60 GHz LC-VCO. The overall circuit is designed to allow measurements of the singles blocks stand-alone and working together. The co-layout is carried on with the EM modelling process of passives devices, parasitics and transmission lines extracted from the layout. The inductors models provided by the foundry are qualified up to 40 GHz, therefore the EM analysis is a must for post-layout simulation. The PVT variations have been simulated before manufacturing and, based on the results achieved, a PLL scheme PVT robust, considering frequency calibration, has been patented. The test chip has been measured in the CEA-Leti (Grenoble) during a stay of one week. The operation principle and the optimization trade-offs among power consumption, and locking ranges of the final selected ILFD topology have been demonstrated. Even if the experimental results are not completely in agreement with the simulations, due to modelling error and inaccuracy, the proposed technique has been validated with post-measurement simulations. As demonstrated, the locking range of a low-power, discrete tuned divide-by-2 ILFD can be enhanced by increasing the injection efficiency, without the drawbacks of higher power consumption and chip area. A 4-bits wide tuning range LC-VCO for mm-W applications has been co-designed using the selected 65 nm CMOS process.Postprint (published version