Energy Efficient Design for Deep Sub-micron CMOS VLSIs

Over the past decade, low power, energy efficient VLSI design has been the focal point of active research and development. The rapid technology scaling, the growing integration capacity, and the mounting active and leakage power dissipation are contributing to the growing complexity of modern VLSI design. Careful power planning on all design levels is required. This dissertation tackles the low-power, low-energy challenges in deep sub-micron technologies on the architecture and circuit levels. Voltage scaling is one of the most efficient ways for reducing power and energy. For ultra-low voltage operation, a new circuit technique which allows bulk CMOS circuits to work in the sub-0. 5V supply territory is presented. The threshold voltage of the slow PMOS transistor is controlled dynamically to get a lower threshold voltage during the active mode. Due to the reduced threshold voltage, switching speed becomes faster while active leakage current is increased. A technique to dynamically manage active leakage current is presented. Energy reduction resulting from using the proposed structure is demonstrated through simulations of different circuits with different levels of complexity. As technology scales, the mounting leakage current and degraded noise immunity impact performance especially that of high performance dynamic circuits. Dual threshold technology shows a good potential for leakage reduction while meeting performance goals. A model for optimally selecting threshold voltages and transistor sizes in wide fan-in dynamic circuits is presented. On the circuit level, a novel circuit level technique which handles the trade-off between noise immunity and energy dissipation for wide fan-in dynamic circuits is presented. Energy efficiency of the proposed wide fan-in dynamic circuit is further enhanced through efficient low voltage operation. Another direct consequence of technology scaling is the growing impact of interconnect parasitics and process variations on performance. Traditionally, worst case process, parasitics, and environmental conditions are considered. Designing for worst case guarantees a fail-safe operation but requires a large delay and voltage margins. This large margin can be recovered if the design can adapt to the actual silicon conditions. Dynamic voltage scaling is considered a key enabler in reducing such margin. An on-chip process identifier to recover the margin required due to process variations is described. The proposed architecture adjusts supply voltage using a hybrid between the one-time voltage setting and the continuous monitoring modes of operation. The interconnect impact on delay is minimized through a novel adaptive voltage scaling architecture. The proposed system recovers the large delay and voltage margins required by conventional systems by closely tracking the actual critical path at anytime. By tracking the actual critical path, the proposed system is robust and more energy efficient compared to both the conventional open-loop and closed-loop systems

Current Comparison Domino based CHSK Domino Logic Technique for Rapid Progression and Low Power Alleviation

The proposed domino logic is developed with the combination of Current Comparison Domino (CCD) logic and Conditional High Speed Keeper (CHSK) domino logic. In order to improve the performance metrics like power, delay and noise immunity, the redesign of CHSK is proposed with the CCD. The performance improvement is based on the parasitic capacitance, which reduces on the dynamic node for robust and rapid process of the circuit. The proposed domino logic is designed with keeper and without keeper to measure the performance metrics of the circuit. The outcomes of the proposed domino logic are better when compared to the existing domino logic circuits. The simulation of the proposed CHSK based on the CCD logic circuit is carried out in Cadence Virtuoso tool

Dynamic gates with hysteresis and configurable noise tolerance

Journal ArticleDynamic logic can provide significant performance and power benefit compared to implementations using static gates. Unfortunately dynamic gates have traditionally suffered from low noise margins, which limits their reliability. A new logic family, called complementary dynamic logic (CDL), is presented. CDL replaces the standard keeper logic with a dual dynamic keeper gate that is applicable to all dynamic gate structures. CDL provides dynamic gates with two novel characteristics: hysteresis and arbitrarily configurable noise margins. However, these two benefits come at the cost of reducing the gain and increasing the energy of the dynamic gate. This paper compares the noise, energy, performance, gain, and total transistor width tradeoffs of CDL and three other logic families applied to a 65nm cell library consisting of 23 functions. The results show that the performance advantages of dynamic domino gates can be maintained while providing significantly enhanced noise margins using CDL structures

Design and Implementation of Novel High Performance Domino Logic

This dissertation presents design and implementation of novel high performance domino logic techniques with increased noise robustness and reduced leakages. The speed and overhead area became the primary parameters of choice for fabrication industry that led to invention of clocked logic styles named as Dynamic logic and Domino logic families. Most importantly, power consumption, noise immunity, speed of operation, area and cost are the predominant parameters for designing any kind of digital logic circuit technique with effective trade-off amongst these parameters depending on the situation and application of design. Because of its high speed and low overhead area domino logic became process of choice for designing of high speed application circuits. The concerning issues are large power consumption and high sensitivity towards noise. Hence, there is a need for designing new domino methodology to meet the requirements by overcoming above mentioned drawbacks which led to ample opportunities for diversified research in this field. Therefore, the outcome of research must be able to handle the primary design parameters efficiently. Besides this, the designed circuit must exhibit high degree of robustness towards noise.In this thesis, few domino logic circuit techniques are proposed to deal with noise and sub-threshold leakages. Effect of signal integrity issues on domino logic techniques is studied. Furthermore, having been subjected to process corner analysis and noise analysis, the overall performance of proposed domino techniques is found to be enhanced despite a few limitations that are mentioned in this work. Besides this, lector based domino and dynamic node stabilized techniques are also proposed and are investigated thoroughly. Simulations show that proposed circuits are showing superior performance. In addition to this, domino based Schmitt triggers with various hysteresis phenomena are designed and simulated. Pre-layout and post-layout simulation results are compared for proposed Schmitt trigger. Simulations reveal that proposed Schmitt trigger techniques are more noise tolerant than CMOS counterparts. Moreover, a test chip for domino based Schmitt trigger is done in UMC 180 nm technology for fabrication

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”

Design and Analysis of Improved Domino Logic with Noise Tolerance and High Performance

The demands of upcoming computing, as well as the challenges of nanometer-era of VLSI design necessitate new digital logic techniques and styles that are at the same time high performance, energy efficient and robust to noise and variation. Dynamic CMOS logic gates are broadly used to design high performance circuits due to their high speed. Conversely, the vital demerit of dynamic logic style is its high noise sensitivity. The main reason for this is the sub-threshold leakage current flowing through the pull down network. With continuous technology scaling, this problem is getting more and more severe. In this thesis, a new noise tolerant dynamic CMOS circuit technique is proposed. In the proposed work, we have enhanced the behavior of the domino CMOS logic. This technique also gets benefit in terms of delay and power. This thesis describes the new low power, noise tolerant and high speed domino logic technique and presents a comparison result of this logic with previously reported schemes. Simulation results prove that, in 180 nm CMOS technology when we used this logic style to realize wide fan-in logic gates, it could achieve maximum level of noise robustness as compared to its basic counterpart. In addition, the logic also works efficiently with sequential circuits. The feasibility of this new technique is demonstrated by means of a real hardware, we have built a custom test-chip in the UMC 180 nm process technology with an ALU core, using the proposed domino logic style for each design block. In this thesis, we have also described the design and implementation of this chip. In addition to this, we have also presented initial power and delay performance comparisons between the circuit level simulated ALU and test-chip implemented in the proposed domino logic style. Finally we conclude that, the thesis contributes a very efficient logic style for wide fan-in gates, which is not only noise robust but also energy efficient and high speed

A Reconfigurable Digital Multiplier and 4:2 Compressor Cells Design

With the continually growing use of portable computing devices and increasingly complex software applications, there is a constant push for low power high speed circuitry to support this technology. Because of the high usage and large complex circuitry required to carry out arithmetic operations used in applications such as digital signal processing, there has been a great focus on increasing the efficiency of computer arithmetic circuitry. A key player in the realm of computer arithmetic is the digital multiplier and because of its size and power consumption, it has moved to the forefront of today\u27s research. A digital reconfigurable multiplier architecture will be introduced. Regulated by a 2-bit control signal, the multiplier is capable of double and single precision multiplication, as well as fault tolerant and dual throughput single precision execution. The architecture proposed in this thesis is centered on a recursive multiplication algorithm, where a large multiplication is carried out using recursions of simpler submultiplier modules. Within each sub-multiplier module, instead of carry save adder arrays, 4:2 compressor rows are utilized for partial product reduction, which present greater efficiency, thus result in lower delay and power consumption of the whole multiplier. In addition, a study of various digital logic circuit styles are initially presented, and then three different designs of 4:2 compressor in Domino Logic are presented and simulation results confirm the property of proposed design in terms of delay, power consumption and operation frequenc

Improved Techniques for High Performance Noise-Tolerant Domino CMOS Logic Circuits

Domino CMOS logic circuit family finds a wide variety of applications in microprocessors, digital signal processors, and dynamic memory due to their high speed and low device count. However, there are inevitable problems that degrade the noise immunity of this family; they are the inevitable leakage current and the charge sharing. Added to the drawbacks is the relatively large power consumption, especially if compared to the static complementary CMOS logic family. To make the matter worse, these drawbacks are more tactile with the scaling of CMOS technology. In my thesis, An introduction to domino logic, The impact of CMOS technology scaling on the performance of domino CMOS logic, Three Phase Domino Logic Circuit, High-performance noise-tolerant circuit techniques for CMOS dynamic logic and other Domino logic techniques are studied and corresponding Domino logic techniques have been designed and simulated. Specifically, the need to decrease the dynamic power consumption forces the designer to use a lower power-supply voltage. This in turn necessitates the reduction of threshold voltage to maintain the performance with the associated increase in sub threshold leakage current. So, a properly sized PMOS keeper must be used to compensate for this leakage. It will be found that the speed, which is the major advantage of domino logic compared to other logic styles, will degrade with CMOS technology scaling due to the contention current of the keeper. To assure high performance in noise tolerant techniques, the inevitable effects like leakage currents and charge distribution have to be minimized. In this thesis few modifications have also been made to already existing domino techniques and different Domino logic circuits are simulated in both Cadence virtuoso (implemented using GPDK090- library of 90nm technology) and Mentor graphics (implemented at different technologies like Tsmc 035.mod, Tsmc 025.mod, Tsmc 018.mod) environments. The performance parameters are also compared with other standard architectures of Domino logic

Hybrid Domino XOR Gate with Dual Threshold Voltage Transistors

At the present time, in integrated circuit technology CMOS, low power design is an important subject in system design. In order to achieve this target, power consumption must be minimized. In this article two new domino XOR gates in 45nm technology are presented. First proposed circuits adopt hybrid transistor topology in the pull-down network with all transistors being low threshold voltages. A second proposed circuit adopts hybrid topology with dual threshold voltage transistors. By eliminating two input inverter and preventing the pulse flow to the output node during the precharge phase, power consumption in this circuit is reduced. First proposed circuit reduces active mode power consumption by  78.91% and 54.55% as compared to standard N-type domino XOR and P-type domino XOR.. Similarly, second proposed circuit reduces active mode power consumption by 81.43% and 59.98% as compared to standard N-type domino XOR and P-type domino XOR

Low-swing signaling for energy efficient on-chip networks

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2011.Cataloged from PDF version of thesis.Includes bibliographical references (p. 65-69).On-chip networks have emerged as a scalable and high-bandwidth communication fabric in many-core processor chips. However, the energy consumption of these networks is becoming comparable to that of computation cores, making further scaling of core counts difficult. This thesis makes several contributions to low-swing signaling circuit design for the energy efficient on-chip networks in two separate projects: on-chip networks optimized for one-to-many multicasts and broadcasts, and link designs that allow on-chip networks to approach an ideal interconnection fabric. A low-swing crossbar switch, which is based on tri-state Reduced-Swing Drivers (RSDs), is presented for the first project. Measurement results of its test chip fabricated in 45nm SOI CMOS show that the tri-state RSD-based crossbar enables 55% power savings as compared to an equivalent full-swing crossbar and link. Also, the measurement results show that the proposed crossbar allows the broadcast-optimized on-chip networks using a single pipeline stage for physical data transmission to operate at 21% higher data rate, when compared with the full-swing networks. For the second project, two clockless low-swing repeaters, a Self-Resetting Logic Repeater (SRLR) and a Voltage-Locked Repeater (VLR), have been proposed and analyzed in simulation only. They both require no reference clock, differential signaling, and bias current. Such digital-intensive properties enable them to approach energy and delay performance of a point-to-point interconnect of variable lengths. Simulated in 45nm SOI CMOS, the 10mm SRLR featured with high energy efficiency consumes 338fJ/b at 5.4Gb/s/ch while the 10mm VLR raises its data rate up to 16.OGb/s/ch with 427fJ/b.by Sunghyun Park.S.M