Impacto e compensação da largura de banda vídeo em amplificadores de potência de elevado rendimento

The aim of this work is to determine, quantify and model the performance degradation of wideband power amplifiers when subject to concurrent multiband excitation, with a particular focus on the average efficiency variation. The origins of this degradation are traced to two main transistor properties: the output baseband current generation by the nonlinear transconductance, and the input baseband current generation by the nonlinear gate-source capacitance variation. Each mechanism is analised separately, first by providing a qualitative and intuitive explanation of the processes that lead to the observed efficiency degradation, and then by deriving models that allow the prediction of the average efficiency dependence with the input signal bandwidth. The resulting knowledge was used to improve matching network design, in order to optimize baseband impedance terminations and prevent the efficiency degradation. The derived models were experimentally validated with several PA prototypes implemented with Gallium Nitride HEMT devices, using both conventional and optimized baseband impedance matching networks, achieving over 400MHz instantaneous bandwidth with uncompromised efficiency. The consolidation of the wideband degradation mechanisms described in this work are an important step for modelling and design of wideband, high-efficiency power amplifiers in current and future concurrent multi-band communication systems.O objetivo deste trabalho é determinar, quantificar e modelar a degradação do desempenho de amplificadores de banda-larga quando submetidos a excitação multi-banda concorrente, com particular ênfase na variação do rendimento energético. As origens desta degradação são devidas a duas das principais propriedades do transístor: a geração de corrente em banda-base na saída pela variação não-linear da transcondutância, e a geração de corrente de banda-base na entrada pela variação não-linear da capacidade interna porta-fonte. Cada um destes mecanismos é analisado isoladamente, primeiro por uma explicação qualitativa e intuitiva dos processos que levam à degradação de eficiência observada e, em seguida, através da derivação de modelos que permitem a previsão da degradação do rendimento médio em função da largura de banda do sinal de entrada. O conhecimento resultante foi utilizado para melhorar o desenvolvimento de malhas de adaptação, por forma a otimizar as terminações de impedância em banda-base e prevenir a degradação do rendimento. Os modelos desenvolvidos foram validados experimentalmente em vários amplificadores de potência implementados com transístores de tecnologia GaN HEMT, utilizando malhas de adaptação convencionais e otimizadas, onde se obteve 400MHz de largura de banda instantânea sem degradação do rendimento. A consolidação dos mecanismos de degradação descritos neste trabalho são um importante passo para a modelação e projeto de amplificadores de elevado rendimento e largura-debanda para os sistemas de comunicação multi-banda concorrente convencionais e do futuro.Programa Doutoral em Engenharia Eletrotécnic

A survey on RF and microwave doherty power amplifier for mobile handset applications

This survey addresses the cutting-edge load modulation microwave and radio frequency power amplifiers for next-generation wireless communication standards. The basic operational principle of the Doherty amplifier and its defective behavior that has been originated by transistor characteristics will be presented. Moreover, advance design architectures for enhancing the Doherty power amplifier’s performance in terms of higher efficiency and wider bandwidth characteristics, as well as the compact design techniques of Doherty amplifier that meets the requirements of legacy 5G handset applications, will be discussed.Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-RFundação para a Ciência e a Tecnologia | Ref. UIDP/50008/201

High efficiency power amplifiers for modern mobile communications: The load-modulation approach

Modern mobile communication signals require power amplifiers able to maintain very high efficiency in a wide range of output power levels, which is a major issue for classical power amplifier architectures. Following the load-modulation approach, efficiency enhancement is achieved by dynamically changing the amplifier load impedance as a function of the input power. In this paper, a review of the widely-adopted Doherty power amplifier and of the other load-modulation efficiency enhancement techniques is presented. The main theoretical aspects behind each method are introduced, and the most relevant practical implementations available in recent literature are reported and discussed

ワイヤレス通信のための先進的な信号処理技術を用いた非線形補償法の研究

The inherit nonlinearity in analogue front-ends of transmitters and receivers have had primary impact on the overall performance of the wireless communication systems, as it gives arise of substantial distortion when transmitting and processing signals with such circuits. Therefore, the nonlinear compensation (linearization) techniques become essential to suppress the distortion to an acceptable extent in order to ensure sufficient low bit error rate. Furthermore, the increasing demands on higher data rate and ubiquitous interoperability between various multi-coverage protocols are two of the most important features of the contemporary communication system. The former demand pushes the communication system to use wider bandwidth and the latter one brings up severe coexistence problems. Having fully considered the problems raised above, the work in this Ph.D. thesis carries out extensive researches on the nonlinear compensations utilizing advanced digital signal processing techniques. The motivation behind this is to push more processing tasks to the digital domain, as it can potentially cut down the bill of materials (BOM) costs paid for the off-chip devices and reduce practical implementation difficulties. The work here is carried out using three approaches: numerical analysis & computer simulations; experimental tests using commercial instruments; actual implementation with FPGA. The primary contributions for this thesis are summarized as the following three points: 1) An adaptive digital predistortion (DPD) with fast convergence rate and low complexity for multi-carrier GSM system is presented. Albeit a legacy system, the GSM, however, has a very strict requirement on the out-of-band emission, thus it represents a much more difficult hurdle for DPD application. It is successfully implemented in an FPGA without using any other auxiliary processor. A simplified multiplier-free NLMS algorithm, especially suitable for FPGA implementation, for fast adapting the LUT is proposed. Many design methodologies and practical implementation issues are discussed in details. Experimental results have shown that the DPD performed robustly when it is involved in the multichannel transmitter. 2) The next generation system (5G) will unquestionably use wider bandwidth to support higher throughput, which poses stringent needs for using high-speed data converters. Herein the analog-to-digital converter (ADC) tends to be the most expensive single device in the whole transmitter/receiver systems. Therefore, conventional DPD utilizing high-speed ADC becomes unaffordable, especially for small base stations (micro, pico and femto). A digital predistortion technique utilizing spectral extrapolation is proposed in this thesis, wherein with band-limited feedback signal, the requirement on ADC speed can be significantly released. Experimental results have validated the feasibility of the proposed technique for coping with band-limited feedback signal. It has been shown that adequate linearization performance can be achieved even if the acquisition bandwidth is less than the original signal bandwidth. The experimental results obtained by using LTE-Advanced signal of 320 MHz bandwidth are quite satisfactory, and to the authors’ knowledge, this is the first high-performance wideband DPD ever been reported. 3) To address the predicament that mobile operators do not have enough contiguous usable bandwidth, carrier aggregation (CA) technique is developed and imported into 4G LTE-Advanced. This pushes the utilization of concurrent dual-band transmitter/receiver, which reduces the hardware expense by using a single front-end. Compensation techniques for the respective concurrent dual-band transmitter and receiver front-ends are proposed to combat the inter-band modulation distortion, and simultaneously reduce the distortion for the both lower-side band and upper-side band signals.電気通信大学201

Recent Developments of Dual-Band Doherty Power Amplifiers for Upcoming Mobile Communications Systems

Power amplifiers in modern and future communications should be able to handle different modulation standards at different frequency bands, and in addition, to be compatible with the previous generations. This paper reviews the recent design techniques that have been used to operate dual-band amplifiers and in particular the Doherty amplifiers. Special attention is focused on the design methodologies used for power splitters, phase compensation networks, impedance inverter networks and impedance transformer networks of such power amplifier. The most important materials of the dual-band Doherty amplifier are highlighted and surveyed. The main problems and challenges covering dual-band design concepts are presented and discussed. In addition, improvement techniques to enhance such operations are also exploited. The study shows that the transistor parasitic has a great impact in the design of a dual-band amplifier, and reduction of the transforming ratio of the inverter simplifies the dual-band design. The offset line can be functionally replaced by a Π-network in dual-band design rather than T-network

Dual-band and switched-band highly efficient power amplifiers

The Power Amplifier is the most challenging module of a wireless network to design and it is the highest power consumer. Lots of research has been dedicated to design highly efficient and linear power amplifiers. The high demand for wireless communication systems creates the requirement for multiband transmitters and receivers. Providing high efficiency for power amplifiers in multiband applications is even more challenging. The work presented in this thesis is focused on designing high efficiency frequency adaptive power amplifiers. Frequency adaptive power amplifiers are categorized in three groups: broadband, multi-band and switched-band power amplifiers. Two main design methodologies of frequency adaptive power amplifiers are proposed in this thesis. They are dual-band and switched-band power amplifiers. The advantages and limitations of their output performances are evaluated. The main goals in this thesis are achieving high efficiency and required output power over all working bands and maintaining consistent performance over the bandwidth. In the dual-band power amplifiers, the distributed matching network is designed without any switches. Both of the switched-band Class-E power amplifiers have switched shunt capacitor values. The results demonstrate the tradeoffs between achieving consistent high performance in each band and introducing losses and complexity in the switching design

Millimeter-Wave Concurrent Dual-Band BiCMOS RFICs for Radar and Communication RF Front-End

The recent advancement in silicon-based technologies has offered the opportunity for the development of highly-integrated circuits and systems in the millimeter-wave frequency regime. In particular, the demand for high performance multi-band multi-mode radar and communication systems built on silicon-based technologies has been increased dramatically for both military and commercial applications. This dissertation presents the design and implementation of advanced millimeter-wave front-end circuits in SiGe BiCMOS process including a transmit/receive switch module with integrated calibration function, low noise amplifier, and power amplifier for millimeter-wave concurrent dual-band dual-polarization radars and communication systems. The proposed circuits designed for the concurrent dual-band dual-polarization radars and communication systems were fabricated using 0.18-μm BiCMOS process resulting in novel circuit architectures for concurrent multi-band operation. The developed concurrent dual-band circuits fabricated on 0.18-μm BiCMOS process include the T/R/Calibration switch module for digital beam forming array system at 24.5/35 GHz, concurrent dual-band low noise amplifiers at 44/60 GHz, and concurrent dual-band power amplifier at 44/60 GHz. With having all the design frequencies closely spaced to each other showing the frequency ratio below 1.43, the designed circuits provided the integrated dual-band filtering function with Q-enhanced frequency responses. Inspired by the composite right/left- handed metamaterial transmission line approaches, the integrated Q-enhanced filtering sub-circuits provided unprecedented dual-band filtering capability. The new concurrent dual-band dual-mode circuits and system architecture can provide enhanced radar and communication system performance with extended coverage, better image synthesis and target locating by the enhanced diversity. The circuit level hardware research conducted in this dissertation is expected to contribute to enhance the performance of multi-band multi-mode imaging, sensing, and communication array systems

Multi-Resonant Class-F Power Amplifier Design for 5G Cellular Networks

yesThis work integrates a harmonic tuning mechanism in synergy with the GaN HEMT transistor for 5G mobile transceiver applications. Following a theoretical study on the operational behavior of the Class-F power amplifier (PA), a complete amplifier design procedure is described that includes the proposed Harmonic Control Circuits for the second and third harmonics and optimum loading conditions for phase shifting of the drain current and voltage waveforms. The performance improvement provided by the Class-F configuration is validated by comparing the experimental and simulated results. The designed 10W Class-F PA prototype provides a measured peak drain efficiency of 64.7% at 1dB compression point of the PA at 3.6GHz frequency