Single-Precision and Double-Precision Merged Floating-Point Multiplication and Addition Units on FPGA

Floating-point (FP) operations defined in IEEE 754-2008 Standard for Floating-Point Arithmetic can provide wider dynamic range and higher precision than fixed-point operations. Many scientific computations and multimedia applications adopt FP operations. Among all the FP operations, addition and multiplication are the most frequent operations. In this thesis, the single-precision (SP) and double-precision (DP) merged FP multiplier and FP adder architectures are proposed. The proposed efficient iterative FP multiplier is designed based on the Karatsuba algorithm and implemented with the pipelined architecture. It can accomplish two parallel SP multiplication operations in one iteration with a latency of 6 clock cycles or one DP multiplication operation in two iterations with a latency of 9 clock cycles. Implemented on Xilinx Virtex-5 (xc5vlx155ff1760-3) FPGA device, the proposed multiplier runs at 348 MHz using 6 DSP48E blocks, 1117 LUTs, and 1370 FFs. Compared to previous FPGA based multiple-precision FP multiplier, the proposed designs runs at 4% faster clock frequency with reduction of 33% of DSP blocks, 17% latency for SP multiplication, and 28% latency for DP multiplication. The proposed high performance FP adder is designed based one the two-path FP addition algorithm. With fully pipelined architecture, the proposed adder can accomplish one DP or two parallel SP addition/subtraction operations in 6 clock cycles. The proposed adder architecture is implemented on both Altera and Xilinx 65nm process FPGA devices. The proposed adder can run up to 336 MHz with 1694 FFs, 1420 LUTs on Xilinx Virtex-5 (xc5vlx155ff1760-3) FPGA device. Compared to the combination of one DP and two SP architecture built with Xilinx FP operator, the proposed adder has 11.3% faster clock frequency. On Altera Stratix-III (EP3SL340F1760C2) FPGA device, the maximum clock frequency of the proposed adder can reach 358 MHz and 1686 ALUTs and 1556 registers are occupied. The proposed adder is 11.6% faster than the combination of one DP and two SP architecture built with Altera FP megafunction. For the reference of other researchers, the implementation results of the proposed FP multiplier and FP adder on the latest Xilinx Virtex-7 device and Altera Arria 10 device are also provided

Optimisations arithmétiques et synthèse de haut niveau

High-level synthesis (HLS) tools offer increased productivity regarding FPGA programming.However, due to their relatively young nature, they still lack many arithmetic optimizations.This thesis proposes safe arithmetic optimizations that should always be applied.These optimizations are simple operator specializations, following the C semantic.Other require to a lift the semantic embedded in high-level input program languages, which are inherited from software programming, for an improved accuracy/cost/performance ratio.To demonstrate this claim, the sum-of-product of floating-point numbers is used as a case study. The sum is performed on a fixed-point format, which is tailored to the application, according to the context in which the operator is instantiated.In some cases, there is not enough information about the input data to tailor the fixed-point accumulator.The fall-back strategy used in this thesis is to generate an accumulator covering the entire floating-point range.This thesis explores different strategies for implementing such a large accumulator, including new ones.The use of a 2's complement representation instead of a sign+magnitude is demonstrated to save resources and to reduce the accumulation loop delay.Based on a tapered precision scheme and an exact accumulator, the posit number systems claims to be a candidate to replace the IEEE floating-point format.A throughout analysis of posit operators is performed, using the same level of hardware optimization as state-of-the-art floating-point operators.Their cost remains much higher that their floating-point counterparts in terms of resource usage and performance. Finally, this thesis presents a compatibility layer for HLS tools that allows one code to be deployed on multiple tools.This library implements a strongly typed custom size integer type along side a set of optimized custom operators.À cause de la nature relativement jeune des outils de synthèse de haut-niveau (HLS), de nombreuses optimisations arithmétiques n'y sont pas encore implémentées. Cette thèse propose des optimisations arithmétiques se servant du contexte spécifique dans lequel les opérateurs sont instanciés.Certaines optimisations sont de simples spécialisations d'opérateurs, respectant la sémantique du C.D'autres nécéssitent de s'éloigner de cette sémantique pour améliorer le compromis précision/coût/performance.Cette proposition est démontré sur des sommes de produits de nombres flottants.La somme est réalisée dans un format en virgule-fixe défini par son contexte.Quand trop peu d’informations sont disponibles pour définir ce format en virgule-fixe, une stratégie est de générer un accumulateur couvrant l'intégralité du format flottant.Cette thèse explore plusieurs implémentations d'un tel accumulateur.L'utilisation d'une représentation en complément à deux permet de réduire le chemin critique de la boucle d'accumulation, ainsi que la quantité de ressources utilisées. Un format alternatif aux nombres flottants, appelé posit, propose d'utiliser un encodage à précision variable.De plus, ce format est augmenté par un accumulateur exact.Pour évaluer précisément le coût matériel de ce format, cette thèse présente des architectures d'opérateurs posits, implémentés avec le même degré d'optimisation que celui de l'état de l'art des opérateurs flottants.Une analyse détaillée montre que le coût des opérateurs posits est malgré tout bien plus élevé que celui de leurs équivalents flottants.Enfin, cette thèse présente une couche de compatibilité entre outils de HLS, permettant de viser plusieurs outils avec un seul code. Cette bibliothèque implémente un type d'entiers de taille variable, avec de plus une sémantique strictement typée, ainsi qu'un ensemble d'opérateurs ad-hoc optimisés

Efficient FPGA implementation and power modelling of image and signal processing IP cores

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Field Programmable Gate Arrays (FPGAs) are the technology of choice in a number ofimage and signal processing application areas such as consumer electronics, instrumentation, medical data processing and avionics due to their reasonable energy consumption, high performance, security, low design-turnaround time and reconfigurability. Low power FPGA devices are also emerging as competitive solutions for mobile and thermally constrained platforms. Most computationally intensive image and signal processing algorithms also consume a lot of power leading to a number of issues including reduced mobility, reliability concerns and increased design cost among others. Power dissipation has become one of the most important challenges, particularly for FPGAs. Addressing this problem requires optimisation and awareness at all levels in the design flow. The key achievements of the work presented in this thesis are summarised here. Behavioural level optimisation strategies have been used for implementing matrix product and inner product through the use of mathematical techniques such as Distributed Arithmetic (DA) and its variations including offset binary coding, sparse factorisation and novel vector level transformations. Applications to test the impact of these algorithmic and arithmetic transformations include the fast Hadamard/Walsh transforms and Gaussian mixture models. Complete design space exploration has been performed on these cores, and where appropriate, they have been shown to clearly outperform comparable existing implementations. At the architectural level, strategies such as parallelism, pipelining and systolisation have been successfully applied for the design and optimisation of a number of cores including colour space conversion, finite Radon transform, finite ridgelet transform and circular convolution. A pioneering study into the influence of supply voltage scaling for FPGA based designs, used in conjunction with performance enhancing strategies such as parallelism and pipelining has been performed. Initial results are very promising and indicated significant potential for future research in this area. A key contribution of this work includes the development of a novel high level power macromodelling technique for design space exploration and characterisation of custom IP cores for FPGAs, called Functional Level Power Analysis and Modelling (FLPAM). FLPAM is scalable, platform independent and compares favourably with existing approaches. A hybrid, top-down design flow paradigm integrating FLPAM with commercially available design tools for systematic optimisation of IP cores has also been developed

High sample-rate Givens rotations for recursive least squares

The design of an application-specific integrated circuit of a parallel array processor is considered for recursive least squares by QR decomposition using Givens rotations, applicable in adaptive filtering and beamforming applications. Emphasis is on high sample-rate operation, which, for this recursive algorithm, means that the time to perform arithmetic operations is critical. The algorithm, architecture and arithmetic are considered in a single integrated design procedure to achieve optimum results. A realisation approach using standard arithmetic operators, add, multiply and divide is adopted. The design of high-throughput operators with low delay is addressed for fixed- and floating-point number formats, and the application of redundant arithmetic considered. New redundant multiplier architectures are presented enabling reductions in area of up to 25%, whilst maintaining low delay. A technique is presented enabling the use of a conventional tree multiplier in recursive applications, allowing savings in area and delay. Two new divider architectures are presented showing benefits compared with the radix-2 modified SRT algorithm. Givens rotation algorithms are examined to determine their suitability for VLSI implementation. A novel algorithm, based on the Squared Givens Rotation (SGR) algorithm, is developed enabling the sample-rate to be increased by a factor of approximately 6 and offering area reductions up to a factor of 2 over previous approaches. An estimated sample-rate of 136 MHz could be achieved using a standard cell approach and O.35pm CMOS technology. The enhanced SGR algorithm has been compared with a CORDIC approach and shown to benefit by a factor of 3 in area and over 11 in sample-rate. When compared with a recent implementation on a parallel array of general purpose (GP) DSP chips, it is estimated that a single application specific chip could offer up to 1,500 times the computation obtained from a single OP DSP chip

The impact of design techniques in the reduction of power consumption of SoCs Multimedia

Orientador: Guido Costa Souza de AraújoDissertação (mestrado) - Universidade Estadual de Campinas, Instituto de ComputaçãoResumo: A indústria de semicondutores sempre enfrentou fortes demandas em resolver problema de dissipação de calor e reduzir o consumo de energia em dispositivos. Esta tendência tem sido intensificada nos últimos anos com o movimento de sustentabilidade ambiental. A concepção correta de um sistema eletrônico de baixo consumo de energia é um problema de vários níveis de complexidade e exige estratégias sistemáticas na sua construção. Fora disso, a adoção de qualquer técnica de redução de energia sempre está vinculada com objetivos especiais e provoca alguns impactos no projeto. Apesar dos projetistas conheçam bem os impactos de forma qualitativa, as detalhes quantitativas ainda são incógnitas ou apenas mantidas dentro do 'know-how' das empresas. Neste trabalho, de acordo com resultados experimentais baseado num plataforma de SoC1 industrial, tentamos quantificar os impactos derivados do uso de técnicas de redução de consumo de energia. Nos concentramos em relacionar o fator de redução de energia de cada técnica aos impactos em termo de área, desempenho, esforço de implementação e verificação. Na ausência desse tipo de dados, que relacionam o esforço de engenharia com as metas de consumo de energia, incertezas e atrasos serão frequentes no cronograma de projeto. Esperamos que este tipo de orientações possam ajudar/guiar os arquitetos de projeto em selecionar as técnicas adequadas para reduzir o consumo de energia dentro do alcance de orçamento e cronograma de projetoAbstract: The semiconductor industry has always faced strong demands to solve the problem of heat dissipation and reduce the power consumption in electronic devices. This trend has been increased in recent years with the action of environmental sustainability. The correct conception of an electronic system for low power consumption is an issue with multiple levels of complexities and requires systematic approaches in its construction. However, the adoption of any technique for reducing the power consumption is always linked with some specific goals and causes some impacts on the project. Although the designers know well that these impacts can affect the design in a quality aspect, the quantitative details are still unkown or just be kept inside the company's know-how. In this work, according to the experimental results based on an industrial SoC2 platform, we try to quantify the impacts of the use of low power techniques. We will relate the power reduction factor of each technique to the impact in terms of area, performance, implementation and verification effort. In the absence of such data, which relates the engineering effort to the goals of power consumption, uncertainties and delays are frequent. We hope that such guidelines can help/guide the project architects in selecting the appropriate techniques to reduce the power consumption within the limit of budget and project scheduleMestradoCiência da ComputaçãoMestre em Ciência da Computaçã

Efficient architectures and power modelling of multiresolution analysis algorithms on FPGA

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.In the past two decades, there has been huge amount of interest in Multiresolution Analysis Algorithms (MAAs) and their applications. Processing some of their applications such as medical imaging are computationally intensive, power hungry and requires large amount of memory which cause a high demand for efficient algorithm implementation, low power architecture and acceleration. Recently, some MAAs such as Finite Ridgelet Transform (FRIT) Haar Wavelet Transform (HWT) are became very popular and they are suitable for a number of image processing applications such as detection of line singularities and contiguous edges, edge detection (useful for compression and feature detection), medical image denoising and segmentation. Efficient hardware implementation and acceleration of these algorithms particularly when addressing large problems are becoming very chal-lenging and consume lot of power which leads to a number of issues including mobility, reliability concerns. To overcome the computation problems, Field Programmable Gate Arrays (FPGAs) are the technology of choice for accelerating computationally intensive applications due to their high performance. Addressing the power issue requires optimi- sation and awareness at all level of abstractions in the design flow. The most important achievements of the work presented in this thesis are summarised here. Two factorisation methodologies for HWT which are called HWT Factorisation Method1 and (HWTFM1) and HWT Factorasation Method2 (HWTFM2) have been explored to increase number of zeros and reduce hardware resources. In addition, two novel efficient and optimised architectures for proposed methodologies based on Distributed Arithmetic (DA) principles have been proposed. The evaluation of the architectural results have shown that the proposed architectures results have reduced the arithmetics calculation (additions/subtractions) by 33% and 25% respectively compared to direct implementa-tion of HWT and outperformed existing results in place. The proposed HWTFM2 is implemented on advanced and low power FPGA devices using Handel-C language. The FPGAs implementation results have outperformed other existing results in terms of area and maximum frequency. In addition, a novel efficient architecture for Finite Radon Trans-form (FRAT) has also been proposed. The proposed architecture is integrated with the developed HWT architecture to build an optimised architecture for FRIT. Strategies such as parallelism and pipelining have been deployed at the architectural level for efficient im-plementation on different FPGA devices. The proposed FRIT architecture performance has been evaluated and the results outperformed some other existing architecture in place. Both FRAT and FRIT architectures have been implemented on FPGAs using Handel-C language. The evaluation of both architectures have shown that the obtained results out-performed existing results in place by almost 10% in terms of frequency and area. The proposed architectures are also applied on image data (256 £ 256) and their Peak Signal to Noise Ratio (PSNR) is evaluated for quality purposes. Two architectures for cyclic convolution based on systolic array using parallelism and pipelining which can be used as the main building block for the proposed FRIT architec-ture have been proposed. The first proposed architecture is a linear systolic array with pipelining process and the second architecture is a systolic array with parallel process. The second architecture reduces the number of registers by 42% compare to first architec-ture and both architectures outperformed other existing results in place. The proposed pipelined architecture has been implemented on different FPGA devices with vector size (N) 4,8,16,32 and word-length (W=8). The implementation results have shown a signifi-cant improvement and outperformed other existing results in place. Ultimately, an in-depth evaluation of a high level power macromodelling technique for design space exploration and characterisation of custom IP cores for FPGAs, called func-tional level power modelling approach have been presented. The mathematical techniques that form the basis of the proposed power modeling has been validated by a range of custom IP cores. The proposed power modelling is scalable, platform independent and compares favorably with existing approaches. A hybrid, top-down design flow paradigm integrating functional level power modelling with commercially available design tools for systematic optimisation of IP cores has also been developed. The in-depth evaluation of this tool enables us to observe the behavior of different custom IP cores in terms of power consumption and accuracy using different design methodologies and arithmetic techniques on virous FPGA platforms. Based on the results achieved, the proposed model accuracy is almost 99% true for all IP core's Dynamic Power (DP) components.Thomas Gerald Gray Charitable Trus

Circuits and Systems Advances in Near Threshold Computing

Modern society is witnessing a sea change in ubiquitous computing, in which people have embraced computing systems as an indispensable part of day-to-day existence. Computation, storage, and communication abilities of smartphones, for example, have undergone monumental changes over the past decade. However, global emphasis on creating and sustaining green environments is leading to a rapid and ongoing proliferation of edge computing systems and applications. As a broad spectrum of healthcare, home, and transport applications shift to the edge of the network, near-threshold computing (NTC) is emerging as one of the promising low-power computing platforms. An NTC device sets its supply voltage close to its threshold voltage, dramatically reducing the energy consumption. Despite showing substantial promise in terms of energy efficiency, NTC is yet to see widescale commercial adoption. This is because circuits and systems operating with NTC suffer from several problems, including increased sensitivity to process variation, reliability problems, performance degradation, and security vulnerabilities, to name a few. To realize its potential, we need designs, techniques, and solutions to overcome these challenges associated with NTC circuits and systems. The readers of this book will be able to familiarize themselves with recent advances in electronics systems, focusing on near-threshold computing