통계적 주파수 검출기 기반 기준 주파수를 사용하지 않는 클록 및 데이터 복원 회로의 설계 방법론

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this thesis, a design of a high-speed, power-efficient, wide-range clock and data recovery (CDR) without a reference clock is proposed. A frequency acquisition scheme using a stochastic frequency detector (SFD) based on the Alexander phase detector (PD) is utilized for the referenceless operation. Pat-tern histogram analysis is presented to analyze the frequency acquisition behavior of the SFD and verified by simulation. Based on the information obtained by pattern histogram analysis, SFD using autocovariance is proposed. With a direct-proportional path and a digital integral path, the proposed referenceless CDR achieves frequency lock at all measurable conditions, and the measured frequency acquisition time is within 7μs. The prototype chip has been fabricated in a 40-nm CMOS process and occupies an active area of 0.032 mm2. The proposed referenceless CDR achieves the BER of less than 10-12 at 32 Gb/s and exhibits an energy efficiency of 1.15 pJ/b at 32 Gb/s with a 1.0 V supply.본 논문은 기준 클럭이 없는 고속, 저전력, 광대역으로 동작하는 클럭 및 데이터 복원회로의 설계를 제안한다. 기준 클럭이 없는 동작을 위해서 알렉산더 위상 검출기에 기반한 통계적 주파수 검출기를 사용하는 주파수 획득 방식이 사용된다. 통계적 주파수 검출기의 주파수 추적 양상을 분석하기 위해 패턴 히스토그램 분석 방법론을 제시하였고 시뮬레이션을 통해 검증하였다. 패턴 히스토그램 분석을 통해 얻은 정보를 바탕으로 자기공분산을 이용한 통계적 주파수 검출기를 제안한다. 직접 비례 경로와 디지털 적분 경로를 통해 제안된 기준 클럭이 없는 클럭 및 데이터 복원회로는 모든 측정 가능한 조건에서 주파수 잠금을 달성하는 데 성공하였고, 모든 경우에서 측정된 주파수 추적 시간은 7μs 이내이다. 40-nm CMOS 공정을 이용하여 만들어진 칩은 0.032 mm2의 면적을 차지한다. 제안하는 클럭 및 데이터 복원회로는 32 Gb/s의 속도에서 비트에러율 10-12 이하로 동작하였고, 에너지 효율은 32Gb/s의 속도에서 1.0V 공급전압을 사용하여 1.15 pJ/b을 달성하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 13 CHAPTER 2 BACKGROUNDS 14 2.1 CLOCKING ARCHITECTURES IN SERIAL LINK INTERFACE 14 2.2 GENERAL CONSIDERATIONS FOR CLOCK AND DATA RECOVERY 24 2.2.1 OVERVIEW 24 2.2.2 JITTER 26 2.2.3 CDR JITTER CHARACTERISTICS 33 2.3 CDR ARCHITECTURES 39 2.3.1 PLL-BASED CDR – WITH EXTERNAL REFERENCE CLOCK 39 2.3.2 DLL/PI-BASED CDR 44 2.3.3 PLL-BASED CDR – WITHOUT EXTERNAL REFERENCE CLOCK 47 2.4 FREQUENCY ACQUISITION SCHEME 50 2.4.1 TYPICAL FREQUENCY DETECTORS 50 2.4.1.1 DIGITAL QUADRICORRELATOR FREQUENCY DETECTOR 50 2.4.1.2 ROTATIONAL FREQUENCY DETECTOR 54 2.4.2 PRIOR WORKS 56 CHAPTER 3 DESIGN OF THE REFERENCELESS CDR USING SFD 58 3.1 OVERVIEW 58 3.2 PROPOSED FREQUENCY DETECTOR 62 3.2.1 MOTIVATION 62 3.2.2 PATTERN HISTOGRAM ANALYSIS 68 3.2.3 INTRODUCTION OF AUTOCOVARIANCE TO STOCHASTIC FREQUENCY DETECTOR 75 3.3 CIRCUIT IMPLEMENTATION 83 3.3.1 IMPLEMENTATION OF THE PROPOSED REFERENCELESS CDR 83 3.3.2 CONTINUOUS-TIME LINEAR EQUALIZER (CTLE) 85 3.3.3 DIGITALLY-CONTROLLED OSCILLATOR (DCO) 87 3.4 MEASUREMENT RESULTS 89 CHAPTER 4 CONCLUSION 99 APPENDIX A DETAILED FREQUENCY ACQUISITION WAVEFORMS OF THE PROPOSED SFD 100 BIBLIOGRAPHY 108 초 록 122박

A 1.8-pJ/b, 12.5-25-Gb/s wide range all-digital clock and data recovery circuit

Recently, there has been a strong drive to replace established analog circuits for multi-gigabit clock and data recovery (CDR) by more digital solutions. We focused on phase locked loop-based all-digital CDR (AD-CDR) techniques which contain a digital loop filter (DLF) and a digital controlled oscillator (DCO) and pushed the digital integration up to a level where our DLF is entirely synthesized. To enable this, we found that extensive subsampling can be used to decrease the speed of the DLF while maintaining a good operation. Additionally, an Inverse Alexander phase detector and a 5.5-bit resolution DCO complete the AD-CDR architecture. As a result of the low complexity and digital architecture, the AD-CDR occupies a compact active chip area of 0.050 mm(2) and consumes only 46 mW at 25 Gb/s. This is the smallest area and the lowest power consumption compared with the state-of-the-art. In addition, our implementation is highly tunable due to the synthesized logic, and supports a wide operating range (12.5-25 Gb/s), which is a significantly larger range compared with the previous work. Finally, thanks to our digital architecture, the power dissipation decreases linearly while moving to the lower speeds of our operating range. This is in contrast with the most prior work, making our design truly adaptive

Architectures and Circuits Leveraging Injection-Locked Oscillators for Ultra-Low Voltage Clock Synthesis and Reference-less Receivers for Dense Chip-to-Chip Communications

High performance computing is critical for the needs of scientific discovery and economic competitiveness. An extreme-scale computing system at 1000x the performance of today’s petaflop machines will exhibit massive parallelism on multiple vertical fronts, from thousands of computational units on a single processor to thousands of processors in a single data center. To facilitate such a massively-parallel extreme-scale computing, a key challenge is power. The challenge is not power associated with base computation but rather the problem of transporting data from one chip to another at high enough rates. This thesis presents architectures and techniques to achieve low power and area footprint while achieving high data rates in a dense very-short reach (VSR) chip-to-chip (C2C) communication network. High-speed serial communication operating at ultra-low supplies improves the energy-efficiency and lowers the power envelop of a system doing an exaflop of loops. One focus area of this thesis is clock synthesis for such energy-efficient interconnect applications operating at high speeds and ultra-low supplies. A sub-integer clockfrequency synthesizer is presented that incorporates a multi-phase injection-locked ring-oscillator-based prescaler for operation at an ultra-low supply voltage of 0.5V, phase-switching based programmable division for sub-integer clock-frequency synthesis, and automatic calibration to ensure injection lock. A record speed of 9GHz has been demonstrated at 0.5V in 45nm SOI CMOS. It consumes 3.5mW of power at 9.12GHz and 0.052 of area, while showing an output phase noise of -100dBc/Hz at 1MHz offset and RMS jitter of 325fs; it achieves a net of -186.5 in a 45-nm SOI CMOS process. This thesis also describes a receiver with a reference-less clocking architecture for high-density VSR-C2C links. This architecture simplifies clock-tree planning in dense extreme-scaling computing environments and has high-bandwidth CDR to enable SSC for suppressing EMI and to mitigate TX jitter requirements. It features clock-less DFE and a high-bandwidth CDR based on master-slave ILOs for phase generation/rotation. The RX is implemented in 14nm CMOS and characterized at 19Gb/s. It is 1.5x faster that previous reference-less embedded-oscillator based designs with greater than 100MHz jitter tolerance bandwidth and recovers error-free data over VSR-C2C channels. It achieves a power-efficiency of 2.9pJ/b while recovering error-free data (BER 200MHz and the INL of the ILO-based phase-rotator (32- Steps/UI) is <1-LSB. Lastly, this thesis develops a time-domain delay-based modeling of injection locking to describe injection-locking phenomena in nonharmonic oscillators. The model is used to predict the locking bandwidth, and the locking dynamics of the locked oscillator. The model predictions are verified against simulations and measurements of a four-stage differential ring oscillator. The model is further used to predict the injection-locking behavior of a single-ended CMOS inverter based ring oscillator, the lock range of a multi-phase injection-locked ring-oscillator-based prescaler, as well as the dynamics of tracking injection phase perturbations in injection-locked masterslave oscillators; demonstrating its versatility in application to any nonharmonic oscillator

Energy-efficient wireline transceivers

Power-efficient wireline transceivers are highly demanded by many applications in high performance computation and communication systems. Apart from transferring a wide range of data rates to satisfy the interconnect bandwidth requirement, the transceivers have very tight power budget and are expected to be fully integrated. This thesis explores enabling techniques to implement such transceivers in both circuit and system levels. Specifically, three prototypes will be presented: (1) a 5Gb/s reference-less clock and data recovery circuit (CDR) using phase-rotating phase-locked loop (PRPLL) to conduct phase control so as to break several fundamental trade-offs in conventional receivers; (2) a 4-10.5Gb/s continuous-rate CDR with novel frequency acquisition scheme based on bang-bang phase detector (BBPD) and a ring oscillator-based fractional-N PLL as the low noise wide range DCO in the CDR loop; (3) a source-synchronous energy-proportional link with dynamic voltage and frequency scaling (DVFS) and rapid on/off (ROO) techniques to cut the link power wastage at system level. The receiver/transceiver architectures are highly digital and address the requirements of new receiver architecture development, wide operating range, and low power/area consumption while being fully integrated. Experimental results obtained from the prototypes attest the effectiveness of the proposed techniques

Design of 10 Gb/s burst-mode receivers for high-split extended reach PONs

The continuous stream of new applications for the internet, increases the need for higher access speed in the currently deployed communication networks. Most networks in use today still consist of twisted copper wires, inherited from the telephone network. The disadvantages of reusing the existing telephone network are twofold. Firstly, the bandwidth of twisted copper wires is limited and secondly, a large number of switches and routers are needed throughout the network leading to an excessive power consumption. The hybrid fiber coax network that reuses the television distribution network is not free from these drawbacks. The bandwidth is also limited and power hungry amplifiers are needed to bridge the distance to and from the user. The future of broadband access lies in optical fiber networks. The optical fiber has a virtually unlimited bandwidth and the lower attenuation leads to less switches and amplifiers in the network, reducing the power consumption of the complete infrastructure. This dissertation describes the design of a 10 Gb/s burst-mode receiver for high-split extended reach passive optical networks (PONs). The designed receiver incorporates two very advanced features. Firstly, the burst-mode receiver locks its gain setting within 6 ns avoiding packet loss due to gain switching during data payload reception. Secondly, the burst-mode receiver detects both burst start and burst end, making it the first burst-mode receiver of its kind to operate without any time critical signal requirements from outside the burst-mode receiver. The presented work covers the chip-level architecture study and design of a 10 Gb/s burst-mode transimpedance amplifier and a 10 Gb/s post-amplifier, which are the two most critical components of a burst-mode receiver

IC design, UWB synchronization circuit

Master'sMASTER OF ENGINEERIN

IUS/payload communication system simulator configuration definition study

The requirements and specifications for a general purpose payload communications system simulator to be used to emulate those communications system portions of NASA and DOD payloads/spacecraft that will in the future be carried into earth orbit by the shuttle are discussed. For the purpose of on-orbit checkout, the shuttle is required to communicate with the payloads while they are physically located within the shuttle bay (attached) and within a range of 20 miles from the shuttle after they have been deployed (detached). Many of the payloads are also under development (and many have yet to be defined), actual payload communication hardware will not be available within the time frame during which the avionic hardware tests will be conducted. Thus, a flexible payload communication system simulator is required

Future benefits and applications of intelligent on-board processing to VSAT services

The trends and roles of VSAT services in the year 2010 time frame are examined based on an overall network and service model for that period. An estimate of the VSAT traffic is then made and the service and general network requirements are identified. In order to accommodate these traffic needs, four satellite VSAT architectures based on the use of fixed or scanning multibeam antennas in conjunction with IF switching or onboard regeneration and baseband processing are suggested. The performance of each of these architectures is assessed and the key enabling technologies are identified