Design strategy for controlled natural aging in Al-Mg-Si alloys

This study presents a design strategy for Al-Mg-Si alloys to control natural aging. Recently, trace addition of Sn was shown to suppress natural aging for up to two weeks, which was explained by the strong trapping of vacancies to Sn atoms. Here we explore the effect of solution treatment temperature, the combination of trace elements such as Sn and In, and the composition of main hardening elements Mg, Si and Cu on natural aging. The results are discussed based on the dissolvable amount of trace elements and their effect on diffusion retardation, and solute clustering mechanisms in Al-Mg-Si alloys. Thermodynamic calculations using the CALPHAD approach show that maximum retardation of natural aging is achievable at the highest trace element solubility, which exists at significantly different solution treatment temperatures for Sn or In. The effects of Mg, Si and Cu content on natural aging kinetics are interpreted via their influence on the Sn solubility and clustering mechanisms. It is proposed that Sn additions reduce the concentration of excess vacancies, which is most important for early Si clustering, and that the effect of Cu is comparable to the effect of Sn, but less pronounced. Based on the investigated parameter space, a design concept is proposed and an Al-Mg-Si alloy showing suppression of natural aging for >6 months and significant artificial aging potential is demonstrated. (C) 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved

Structural analysis and corrosion studies on an ISO 5832-9 biomedical alloy with TiO2 sol–gel layers

The aim of this study was to demonstrate the relationship between the structural and corrosion properties of an ISO 5832-9 biomedical alloy modified with titanium dioxide (TiO2) layers. These layers were obtained via the sol–gel method by acid-catalyzed hydrolysis of titanium isopropoxide in isopropanol solution. To obtain TiO2 layers with different structural properties, the coated samples were annealed at temperatures of 200, 300, 400, 450, 500, 600 and 800 C for 2 h. For all the prepared samples, accelerated corrosion measurements were performed in Tyrode’s physiological solution using electrochemical methods. The most important corrosion parameters were determined: corrosion potential, polarization resistance, corrosion rate, breakdown and repassivation potentials. Corrosion damage was analyzed using scanning electron microscopy. Structural analysis was carried out for selected TiO2 coatings annealed at 200, 400, 600 and 800 C. In addition, the morphology, chemical composition, crystallinity, thickness and density of the deposited TiO2 layers were determined using suitable electron and X-ray measurement methods. It was shown that the structure and character of interactions between substrate and deposited TiO2 layers depended on annealing temperature. All the obtained TiO2 coatings exhibit anticorrosion properties, but these properties are related to the crystalline structure and character of substrate–layer interaction. From the point of view of corrosion, the best TiO2 sol–gel coatings for stainless steel intended for biomedical applications seem to be those obtained at 400 C.This study was supported by Grant No. N N507 501339 of the National Science Centre. The authors wish to express their thanks to J. Borowski (MEDGAL, Poland) for the Rex 734 alloy

High-Strength Low-Alloy (HSLA) Mg-Zn-Ca Alloys with Excellent Biodegradation Performance

This article deals with the development of fine-grained high-strength low-alloy (HSLA) magnesium alloys intended for use as biodegradable implant material. The alloys contain solely low amounts of Zn and Ca as alloying elements. We illustrate the development path starting from the high-Zn-containing ZX50 (MgZn5Ca0.25) alloy with conventional purity, to an ultrahigh-purity ZX50 modification, and further to the ultrahigh-purity Zn-lean alloy ZX10 (MgZn1Ca0.3). It is shown that alloys with high Zn-content are prone to biocorrosion in various environments, most probably because of the presence of the intermetallic phase Mg6Zn3Ca2. A reduction of the Zn content results in (Mg,Zn)2Ca phase formation. This phase is less noble than the Mg-matrix and therefore, in contrast to Mg6Zn3Ca2, does not act as cathodic site. A fine-grained microstructure is achieved by the controlled formation of fine and homogeneously distributed (Mg,Zn)2Ca precipitates, which influence dynamic recrystallization and grain growth during hot forming. Such design scheme is comparable to that of HSLA steels, where low amounts of alloying elements are intended to produce a very fine dispersion of particles to increase the material's strength by refining the grain size. Consequently our new, ultrapure ZX10 alloy exhibits high strength (yield strength R p=240MPa, ultimate tensile strength R m=255MPa) and simultaneously high ductility (elongation to fracture A=27%), as well as low mechanical anisotropy. Because of the anodic nature of the (Mg,Zn)2Ca particles used in the HSLA concept, the in vivo degradation in a rat femur implantation study is very slow and homogeneous without clinically observable hydrogen evolution, making the ZX10 alloy a promising material for biodegradable implants

Retrieval analysis of different orthodontic brackets: the applicability of electron microprobe techniques for determining material heterogeneities and corrosive potential

OBJECTIVE: The objective of this study was to investigate the applicability of micro-analytical methods with high spatial resolution to the characterization of the composition and corrosion behavior of two bracket systems. MATERIAL AND METHODS: The surfaces of six nickel-free brackets and six nickel-containing brackets were examined for signs of corrosion and qualitative surface analysis using an electron probe microanalyzer (EPMA), prior to bonding to patient's tooth surfaces and four months after clinical use. The surfaces were characterized qualitatively by secondary electron (SE) images and back scattered electron (BSE) images in both compositional and topographical mode. Qualitative and quantitative wavelength-dispersive analyses were performed for different elements, and by utilizing qualitative analysis the relative concentration of selected elements was mapped two-dimensionally. The absolute concentration of the elements was determined in specially prepared brackets by quantitative analysis using pure element standards for calibration and calculating correction-factors (ZAF). RESULTS: Clear differences were observed between the different bracket types. The nickel-containing stainless steel brackets consist of two separate pieces joined by a brazing alloy. Compositional analysis revealed two different alloy compositions, and reaction zones on both sides of the brazing alloy. The nickel-free bracket was a single piece with only slight variation in element concentration, but had a significantly rougher surface. After clinical use, no corrosive phenomena were detectable with the methods applied. Traces of intraoral wear at the contact areas between the bracket slot and the arch wire were verified. CONCLUSION: Electron probe microanalysis is a valuable tool for the characterization of element distribution and quantitative analysis for corrosion studies

Hardening of Nitrogen Alloyed Steels by Shock Waves

Nitrogen alloyed steels can suffer a very high deformation without the austenite becoming instable. An ultimate tensile strength over 3000 MPa was achieved by cold drawing. In this work it was tried to harden this steel by shock waves. Plates with a diameter up to 50 mm and a thickness of 10 mm were used. Cr-Mn-steels which were alloyed with 0.53%, 0.61% and 0.89% nitrogen have been studied. The plates have been shock loaded with pressure peaks from 100 to 600 kbar at shock pulse duration from 0.5 µs. 1.2 µs and 3 µs. Vickers hardness VH30 was measured at the shock loaded plates. The increase in hardness rises constantly (without saturation) up to 600 kbar. Mechanical properties were also determined by quasistatic and dynamic (SHPB) compression tests. Toughness was also studied. The results show a very high strain rate sensibility even at elevated hardness. The influence of shock waves on the microstructure was studied optical microscopy.Les aciers alliés à l'azote supportent de très grandes déformations sans que l'austénite ne devienne instabble. Une résistance maximale à la traction de plus de 3000 MPa a été atteinte par étirage à froid. Dans cette étude le durcissement de cet acier par onde de choc a été testé des plaques jusqu'à 50 mm de diamètre et 10 mm d'épaisseur ont été utilisées. Des aciers au chrome-manganèse alliés à 0.53%, 0.61% et 0.89% d'azote ont été étudiés. Ces plaques ont été soumis à des chocs d'une pression de 100 à 600 kbar et d'une durée de 0.5 µs, 1.2 µs et 3 µs. Des duretés Vickers HV30 ont été mesurées sur les plaques choquées. L'accroisement de dureté se poursuit de manière continue (sans saturation) jusqu'à 600 kbar. Les propriétés mécaniques ont également été déterminées au moyen d'essais de compression en statique et en anamique (sur barres d'hopkinson). La ténacité a aussi été étudiée. Les résultats montrent une sensibilité à la vitesse de déformation très élevée même à dureté élevée L'influence des ondes de chocs sur la microsructure a été étudiée par microscopie optique

Clustering in Age-Hardenable Aluminum Alloys

This review gives an overview of the effects of clusters in various aluminum alloys. Characterization methods are discussed in general and results for the important AlMgSi alloys are presented in detail. Indirect characterization methods, such as hardness, tensile testing, electrical resistivity, differential scanning calorimetry, and positron annihilation spectroscopy are discussed, as well as atom probe tomography for the direct measurement of clusters. A particular focus is set on atom probe tomography, where possible artifacts influencing the cluster measurements as well as different cluster finding methods are summed up. A comprehensive summary of investigated alloys and cluster algorithm parameters is given. Moreover, the findings in AlMgSi alloys regarding clusters and changes upon different heat treatments are discussed, starting from early to the latest works. Drawn conclusions are discussed and compared to give a résumé. © 2018 The Authors. Published by Wiley-VCH Verlag GmbH Co.KGaA, Weinhei

Atom Probe Tomography Investigations of Modified Early Stage Clustering in Si-Containing Aluminum Alloys

In this paper atom probe tomography is used to explore early stage clustering in aluminum alloys. Two novel concepts for a modification of clustering are discussed. Control of early stage clustering is welcome from an application point of view since clustering deteriorates strength evolution during the industrial heat treatment of the important class of Al-Mg-Si precipitation-hardenable alloys. Nanoscale early stage clusters are very difficult to observe and atom probe tomography is the best technique to visualize and chemically measure Si or Mg-containing clusters in aluminum alloys. Restrictions remain in achieving the ultimate quantification of such small solute aggregates by atom probe tomography, such as detection efficiency, local magnification effects, surface migration of solute atoms, and unresolved issues with the reconstruction procedure. Here we investigate one of these restricting effects, namely the migration of solute atoms during atom probe tomography measurements. In particular Si is found to be preferentially localized or absent at certain crystallographic poles in aluminum, which derogates the experimental results gained from atom probe tomography studies of clustering in Si-containing aluminum alloys. This artifact is investigated for different specimen temperatures, detection rates and pulse fractions during atom probe tomography measurements. Optimal strategies to analyze small-scale solute clusters in Si-containing aluminum alloys are presented