58 research outputs found
Photon Diffusion in Microscale Solids
This paper presents a theoretical and experimental investigation of photon
diffusion in highly absorbing microscale graphite. An Nd:YAG continuous wave
(CW) laser is used to heat the graphite samples with thicknesses of 40 microns
and 100 microns. Optical intensities of 10 kW/cm^2 and 20 kW/cm^2 are used in
laser heating. The graphite samples are heated to temperatures of thousands of
kelvins within milliseconds, which are recorded by a 2-color, high-speed
pyrometer. To compare the observed temperatures, the differential equation of
heat conduction is solved across the samples with proper initial and boundary
conditions. In addition to lattice vibrations, photon diffusion is incorporated
into the analytical model of thermal conductivity for solving the heat
equation. The numerical simulations showed close matching between experiment
and theory only when including the photon diffusion equations and existing
material properties data found in the previously published works with no
fitting constants. The results indicate that the commonly-overlooked mechanism
of photon diffusion dominates the heat transfer of many microscale structures
near their evaporation temperatures. In addition, the treatment explains the
discrepancies between thermal conductivity measurements and theory that were
previously described in the scientific literature.Comment: 8 pages, 7 figures, (N.B. there is a typo and minor correction in
Table 1 and References in the online version of the journal, corrected and
highlighted in this PDF
Electrically controlled modulation in a photonic crystal nanocavity
We describe a compact modulator based on a planar photonic crystal nanocavity
whose resonance is electrically controlled. A forward bias applied across a
p-i-n diode shifts the cavity into and out of resonance with a continuous-wave
laser field in a waveguide. The sub-micron size of the nanocavity promises
extremely low capacitance, high bandwidth, and efficient on-chip integration in
optical interconnects.Comment: 9 pages, 4 figure
Thermomechanical characterization of on-chip buckled dome Fabry-Perot microcavities
We report on the thermomechanical and thermal tuning properties of
curved-mirror Fabry-Perot resonators, fabricated by the guided assembly of
circular delamination buckles within a multilayer a-Si/SiO2 stack. Analytical
models for temperature dependence, effective spring constants, and mechanical
mode frequencies are described and shown to be in good agreement with
experimental results. The cavities exhibit mode volumes as small as
, reflectance-limited finesse , and
mechanical resonance frequencies in the MHz range. Monolithic cavity arrays of
this type might be of interest for applications in sensing, cavity quantum
electrodynamics, and optomechanics.Comment: \c{opyright} 2015 Optical Society of America. One print or electronic
copy may be made for personal use only. Systematic reproduction and
distribution, duplication of any material in this paper for a fee or for
commercial purposes, or modifications of the content of this paper are
prohibite
High power laser heating of low absorption materials
The article of record as published may be found at http://dx.doi.org/10.1063/1.4896750A model is presented and confirmed experimentally that explains the anomalous behavior observed in continuous wave (CW) excitation of thermally isolated optics. Distributed Bragg Reflector (DBR) high reflective optical thin film coatings of HfOâ‚‚ and SiOâ‚‚were prepared with a very low absorption, about 7 ppm, measured by photothermal common-path interferometry. When illuminated with a 17 kW CW laser for 30 s, the coatings survived peak irradiances of 13 MW/cm², on 500 μm diameter spot cross sections. The temperature profile of the optical surfaces was measured using a calibrated thermal imaging camera for illuminated spot sizes ranging from 500 μm to 5 mm; about the same peak temperatures were recorded regardless of spot size. This phenomenon is explained by solving the heat equation for an optic of finite dimensions and taking into account the non-idealities of the experiment. An analytical result is also derived showing the relationship between millisecond pulse to CW laser operation where (1) the heating is proportional to the laser irradiance (W/m²) for millisecond pulses, (2) the heating is proportional to the beam radius (W/m) for CW, and (3) the heating is proportional to W/m∙ tanâ»Â¹(√(t)/m) in the transition region between the two
Continuous-wave laser particle conditioning: thresholds and time scales
The article of record as published may be found at http://dx.doi.org/10.1016/j.optlastec.2016.09.030The optical absorption of contaminants on high reflectivity mirrors was measured using photo thermal
common-path interferometry before and after exposure to high power continuous-wave laser light. The
contaminants were micron-sized graphite flakes on hafnia-silica distributed Bragg reflectors
illuminated by a ytterbium-doped fiber laser. After one-second periods of exposure, the mirrors
demonstrated reduced absorption for irradiances as low as 11 kW cm−2 and had an obvious threshold
near 20 kW cm−2. Final absorption values were reduced by up to 90% of their initial value for
irradiances of 92 kW cm−2. For shorter pulses at 34 kW cm−2, a minimum exposure time required to
begin absorption reduction was found between 100 μs and 200 μs, with particles reaching their final
minimum absorption value within 300 ms. Microscope images of the surface showed agglomerated
particles fragmenting with some being removed completely, probably by evaporation for exposures
between 200 μs to 10 ms. Exposures of 100 ms and longer left behind a thin semi-transparent
residue, covering much of the conditioned area. An order of magnitude estimate of the time
necessary to begin altering the surface contaminants (also known as ”conditioning”) indicates about
200 μs seconds at 34 kW cm−2, based on heating an average carbon particle to its sublimation
temperature including energy loss to thermal contact and radiation. This estimation is close to the
observed exposure time required to begin absorption reduction.Office of Naval research (ONR)N00014-12-1-1030 (ONR
Efficiency optimization and analysis of 808nm VCSELs with a full electro-thermal-optical numerical model
- …