Measurement of (n,) reaction cross section of W-186-isotope at neutron energy of 20.02±0.58 MeV

The cross-section of 186W(n,)187W reaction has been measured at an average neutron energy of 20.02±0.58 MeV by using activation technique. The 27Al(n,)24Na and 115In(n,n´)115mIn reactions have been used for absolute neutron flux measurement. Theoretically the reaction cross-sections have been calculated by using the TALYS-1.9 code. The results from the present work and the EXFOR based literature data have been compared with the evaluated data and calculated data from TALYS-1.9 code

Monovision-based vehicle detection, distance and relative speed measurement in urban traffic

This study presents a monovision-based system for on-road vehicle detection and computation of distance and relative speed in urban traffic. Many works have dealt with monovision vehicle detection, but only a few of them provide the distance to the vehicle which is essential for the control of an intelligent transportation system. The system proposed integrates a single camera reducing the monetary cost of stereovision and RADAR-based technologies. The algorithm is divided in three major stages. For vehicle detection, the authors use a combination of two features: the shadow underneath the vehicle and horizontal edges. They propose a new method for shadow thresholding based on the grey-scale histogram assessment of a region of interest on the road. In the second and third stages, the vehicle hypothesis verification and the distance are obtained by means of its number plate whose dimensions and shape are standardised in each country. The analysis of consecutive frames is employed to calculate the relative speed of the vehicle detected. Experimental results showed excellent performance in both vehicle and number plate detections and in the distance measurement, in terms of accuracy and robustness in complex traffic scenarios and under different lighting conditions

Synthesis of nanostructured spherical aluminum oxide powders by plasma engineering

Irregularly shaped aluminum oxide particles were plasma atomized resulting in narrow size range distribution of spherical nanostructured powders. Cooling rates, on the order of 106 to 108 K/s, were obtained from the different quenching medias, viz. air, water, and liquid nitrogen. Plasma-engineered powder particles developed nanosize crystallites, while solidification provided insight into the morphological feasibility in refinement of grain size. X-ray diffraction (XRD) methods have been used to quantify the crystallite size obtained with different quenching media. Raman peak shift validated the X-ray analysis in anticipating the grain refinement with increasing cooling rates. Salient structural morphology characteristics and a detailed understanding of spheroidized plasma-sprayed alumina powders were analyzed through scanning electron microscopy (SEM) studies. Formation of nanograins, novel metastable phases, and amorphous structure were endorsed by transmission electron microscopy (TEM) investigations

Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel

Retained austenite transformation was studied for a 5 wt pct Cr cold work tool steel tempered at 798 K and 873 K (525 degrees C and 600 degrees C) followed by cooling to room temperature. Tempering cycles with variations in holding times were conducted to observe the mechanisms involved. Phase transformations were studied with dilatometry, and the resulting microstructures were characterized with X-ray diffraction and scanning electron microscopy. Tempering treatments at 798 K (525 degrees C) resulted in retained austenite transformation to martensite on cooling. The martensite start (M-s) and martensite finish (M-f) temperatures increased with longer holding times at tempering temperature. At the same time, the lattice parameter of retained austenite decreased. Calculations from the Ms temperatures and lattice parameters suggested that there was a decrease in carbon content of retained austenite as a result of precipitation of carbides prior to transformation. This was in agreement with the resulting microstructure and the contraction of the specimen during tempering, as observed by dilatometry. Tempering at 873 K (600 degrees C) resulted in precipitation of carbides in retained austenite followed by transformation to ferrite and carbides. This was further supported by the initial contraction and later expansion of the dilatometry specimen, the resulting microstructure, and the absence of any phase transformation on cooling from the tempering treatment. It was concluded that there are two mechanisms of retained austenite transformation occurring depending on tempering temperature and time. This was found useful in understanding the standard tempering treatment, and suggestions regarding alternative tempering treatments are discussed. (C) The Author(s) 2017.Funders: Uddeholm AB</p