34 research outputs found
High density p-type Bi0.5Sb1.5Te3 nanowires by electrochemical templating through ion-track lithography
High density p-type Bi0.5Sb1.5Te3 nanowire arrays are produced by a combination of electrodeposition and ion-track lithography technology. Initially, the electrodeposition of p-type wBi(0.5)Sb(1.5)Te(3) films is investigated to find out the optimal conditions for the deposition of nanowires. Polyimide-based Kapton foils are chosen as a polymer for ion track irradiation and nanotemplating Bi0.5Sb1.5Te3 nanowires. The obtained nanowires have average diameters of 80 nm and lengths of 20 mu m, which are equivalent to the pore size and thickness of Kapton foils. The nanowires exhibit a preferential orientation along the {110} plane with a composition of 11.26 at.% Bi, 26.23 at.% Sb, and 62.51 at.% Te. Temperature dependence studies of the electrical resistance show the semiconducting nature of the nanowires with a negative temperature coefficient of resistance and band gap energy of 0.089 +/- 0.006 eV
Vibration based electromagnetic micropower generator on silicon
This paper discusses the theory, design and simulation of electromagnetic micropower generators with electroplated micromagnets. The power generators are fabricated using standard microelectromechanical system processing techniques. Electromagnetic two-dimensional finite element anlysis simulations are used to determine voltage and power that can be generated from different designs. This paper reports a maximum voltage and power of 55 mV and 70 mu W for the first design, incorporating microfabricated two-layer Cu coils on a Si paddle vibrating between two sets of oppositely polarized electroplated Co50Pt50 face centered tetragonal phase hard magnets. A peak voltage and power of 950 mV and 85 mu W are obtained for the second design, which includes electroplated Ni45Fe55 as a soft magnetic layer underneath the hard magnets. The volume of the device is about 30 mm(3)
Effect of bandage materials on epidermal antenna
This study explores the effect of different types of bandages on the performance of an epidermal antenna. Three identical dipole antennas are designed on three different types of bandages, and the measured reflection coefficients, S11, show that the antennas resonate at the same frequency despite the different types of fabric bandages. However, the antennas resonance frequency shifts to a lower frequency when the antennas are mounted on the body. The transmission coefficient, S21, over a 60 cm link with a standard RFID antenna is at least −30 dB, and −34 dB in free space and on the body, respectively, demonstrating that the antenna is suitable for communication and wireless RF power transfer in wearable applications
Sensory motor systems of artificial and natural hands
The surgeon Ambroise Paré designed an anthropomorphic hand for wounded soldiers in the 16th century. Since that time, there have been advances in technology through the use of computer-aided design, modern materials, electronic controllers and sensors to realise artificial hands which have good functionality and reliability. Data from touch, object slip, finger position and temperature sensors, mounted in the fingers and on the palm, can be used in feedback loops to automatically hold objects. A study of the natural neuromuscular systems reveals a complexity which can only in part be realised today with technology. Highlights of the parallels and differences between natural and artificial hands are discussed with reference to the Southampton Hand. The anatomical structure of parts of the natural systems can be made artificially such as the antagonist muscles using tendons. Theses solutions look promising as they are based on the natural form but in practice lack the desired physical specification. However, concepts of the lower spinal loops can be mimicked in principle. Some future devices will require greater skills from the surgeon to create the interface between the natural system and an artificial device. Such developments may offer a more natural control with ease of use for the limb deficient person
Screen Printable Flexible BiTe–SbTe-Based Composite Thermoelectric Materials on Textiles for Wearable Applications
A Flexible 2.45-GHz Power Harvesting Wristband with Net System Output from -24.3 dBm of RF Power
This paper presents a flexible 2.45-GHz wireless power harvesting wristband that generates a net dc output from a -24.3-dBm RF input. This is the lowest reported system sensitivity for systems comprising a rectenna and impedance-matching power management. A complete system has been implemented comprising: a fabric antenna, a rectifier on rigid substrate, a contactless electrical connection between rigid and flexible subsystems, and power electronics impedance matching. Various fabric and flexible materials are electrically characterized at 2.45 GHz using the two-line and the T-resonator methods. Selected materials are used to design an all-textile antenna, which demonstrates a radiation efficiency above 62% on a phantom irrespective of location, and a stable radiation pattern. The rectifier, designed on a rigid substrate, shows a best-in-class efficiency of 33.6% at -20 dBm. A reliable, efficient, and wideband contactless connection between the fabric antenna and the rectifier is created using broadside-coupled microstrip lines, with an insertion loss below 1 dB from 1.8 to over 10 GHz. A self-powered boost converter with a quiescent current of 150 nA matches the rectenna output with a matching efficiency above 95%. The maximum end-to-end efficiency is 28.7% at -7 dBm. The wristband harvester demonstrates net positive energy harvesting from -24.3 dBm, a 7.3-dB improvement on the state of the art.</p
Roadmap on energy harvesting materials
Ambient energy harvesting has great potential to contribute to sustainable development and address growing environmental challenges. Converting waste energy from energy-intensive processes and systems (e.g. combustion engines and furnaces) is crucial to reducing their environmental impact and achieving net-zero emissions. Compact energy harvesters will also be key to powering the exponentially growing smart devices ecosystem that is part of the Internet of Things, thus enabling futuristic applications that can improve our quality of life (e.g. smart homes, smart cities, smart manufacturing, and smart healthcare). To achieve these goals, innovative materials are needed to efficiently convert ambient energy into electricity through various physical mechanisms, such as the photovoltaic effect, thermoelectricity, piezoelectricity, triboelectricity, and radiofrequency wireless power transfer. By bringing together the perspectives of experts in various types of energy harvesting materials, this Roadmap provides extensive insights into recent advances and present challenges in the field. Additionally, the Roadmap analyses the key performance metrics of these technologies in relation to their ultimate energy conversion limits. Building on these insights, the Roadmap outlines promising directions for future research to fully harness the potential of energy harvesting materials for green energy anytime, anywhere
Effects of the binder material on the mechanical properties of thick-film magnetostrictive materials
This paper presents research carried out at the University of Southampton into the development of a magnetostrictive thick-film material suitable for use with silicon micromachined devices. This form of magnetostrictive material has previously been deposited onto alumina substrates and this paper reports further work on migrating the technology onto silicon. The evaluation of two alternative glass frits for use as the binder within the thick film is reported. The correct choice of the binder material is important in a thick-film material because it is responsible for binding the active material within the thick film into a composite material and also adhering the film to the substrate. A series of tests have been applied to samples fabricated using various glass frits to assess their mechanical properties and suitability for the micro-actuator applications
Screen printed piezoelectric generator for helicopter health and usage monitoring systems
This paper presents a piezoelectric vibration energy harvester fabricated using screen printing. The formulation of a novel tungsten based polymer ink enables the deposition of an inertial mass enabling the entire structure to be fabricated by the printing process. The devices have been designed for use on an aircraft Health and Usage Monitoring System (HUMS). Initial devices produce a peak power of 117?w at 6.9m/s2 and 70Hz with an optimum load of 140kW and an output voltage of 2.9V