1,077 research outputs found
Realization of low-loss mirrors with sub-nanometer flatness for future gravitational wave detectors
The second generation of gravitational wave detectors will aim at improving by an order of magnitude their sensitivity versus the present ones (LIGO and VIRGO). These detectors are based on long-baseline Michelson interferometer with high finesse Fabry-Perot cavity in the arms and have strong requirements on the mirrors quality. These large low-loss mirrors (340 mm in diameter, 200 mm thick) must have a near perfect flatness. The coating process shall not add surface figure Zernike terms higher than second order with amplitude >0.5 nm over the central 160 mm diameter. The limits for absorption and scattering losses are respectively 0.5 and 5 ppm. For each cavity the maximum loss budget due to the surface figure error should be smaller than 50 ppm. Moreover the transmission matching between the two inputs mirrors must be better than 99%.
We describe the different configurations that were explored in order to respect all these requirements. Coatings are done using IBS.
The two first configurations based on a single rotation motion combined or not with uniformity masks allow to obtain coating thickness uniformity around 0.2 % rms on 160 mm diameter. But this is not sufficient to meet all the specifications.
A planetary motion completed by masking technique has been studied. With simulated values the loss cavity is below 20 ppm, better than the requirements. First experimental results obtained with the planetary system will be presented
Interrupt Timed Automata: verification and expressiveness
We introduce the class of Interrupt Timed Automata (ITA), a subclass of
hybrid automata well suited to the description of timed multi-task systems with
interruptions in a single processor environment. While the reachability problem
is undecidable for hybrid automata we show that it is decidable for ITA. More
precisely we prove that the untimed language of an ITA is regular, by building
a finite automaton as a generalized class graph. We then establish that the
reachability problem for ITA is in NEXPTIME and in PTIME when the number of
clocks is fixed. To prove the first result, we define a subclass ITA- of ITA,
and show that (1) any ITA can be reduced to a language-equivalent automaton in
ITA- and (2) the reachability problem in this subclass is in NEXPTIME (without
any class graph). In the next step, we investigate the verification of real
time properties over ITA. We prove that model checking SCL, a fragment of a
timed linear time logic, is undecidable. On the other hand, we give model
checking procedures for two fragments of timed branching time logic. We also
compare the expressive power of classical timed automata and ITA and prove that
the corresponding families of accepted languages are incomparable. The result
also holds for languages accepted by controlled real-time automata (CRTA), that
extend timed automata. We finally combine ITA with CRTA, in a model which
encompasses both classes and show that the reachability problem is still
decidable. Additionally we show that the languages of ITA are neither closed
under complementation nor under intersection
INTERNAL FRICTION AND YOUNG'S MODULUS MEASUREMENTS ON SiO2 AND Ta2O5 FILMS DONE WITH AN ULTRA-HIGH Q SILICON-WAFER SUSPENSION
International audienceIn order to study the internal friction of thin films a nodal suspension system called GeNS (Gentle Nodal Suspension) has been developed. The key features of this system are: i) the possibility to use substrates easily available like silicon wafers; ii) extremely low excess losses coming from the suspension system which allows to measure Q factors in excess of 2×10^8 on 3 " diameter wafers; iii) reproducibility of measurements within few percent on mechanical losses and 0.01% on resonant frequencies; iv) absence of clamping; v) the capability to operate at cryogenic temperatures. Measurements at cryogenic temperatures on SiO 2 and at room temperature only on Ta2O5 films deposited on silicon are presented
Reconstruction of the gravitational wave signal during the Virgo science runs and independent validation with a photon calibrator
The Virgo detector is a kilometer-scale interferometer for gravitational wave
detection located near Pisa (Italy). About 13 months of data were accumulated
during four science runs (VSR1, VSR2, VSR3 and VSR4) between May 2007 and
September 2011, with increasing sensitivity.
In this paper, the method used to reconstruct, in the range 10 Hz-10 kHz, the
gravitational wave strain time series from the detector signals is
described. The standard consistency checks of the reconstruction are discussed
and used to estimate the systematic uncertainties of the signal as a
function of frequency. Finally, an independent setup, the photon calibrator, is
described and used to validate the reconstructed signal and the
associated uncertainties.
The uncertainties of the time series are estimated to be 8% in
amplitude. The uncertainty of the phase of is 50 mrad at 10 Hz with a
frequency dependence following a delay of 8 s at high frequency. A bias
lower than and depending on the sky direction of the GW is
also present.Comment: 35 pages, 16 figures. Accepted by CQ
Virgo calibration and reconstruction of the gravitational wave strain during VSR1
Virgo is a kilometer-length interferometer for gravitational waves detection
located near Pisa. Its first science run, VSR1, occured from May to October
2007. The aims of the calibration are to measure the detector sensitivity and
to reconstruct the time series of the gravitational wave strain h(t). The
absolute length calibration is based on an original non-linear reconstruction
of the differential arm length variations in free swinging Michelson
configurations. It uses the laser wavelength as length standard. This method is
used to calibrate the frequency dependent response of the Virgo mirror
actuators and derive the detector in-loop response and sensitivity within ~5%.
The principle of the strain reconstruction is highlighted and the h(t)
systematic errors are estimated. A photon calibrator is used to check the sign
of h(t). The reconstructed h(t) during VSR1 is valid from 10 Hz up to 10 kHz
with systematic errors estimated to 6% in amplitude. The phase error is
estimated to be 70 mrad below 1.9 kHz and 6 micro-seconds above.Comment: 8 pages, 8 figures, proceedings of Amaldi 8 conference, to be
published in Journal of Physics Conference Series (JPCS). Second release:
correct typo
Sensitivity Studies for Third-Generation Gravitational Wave Observatories
Advanced gravitational wave detectors, currently under construction, are
expected to directly observe gravitational wave signals of astrophysical
origin. The Einstein Telescope, a third-generation gravitational wave detector,
has been proposed in order to fully open up the emerging field of gravitational
wave astronomy. In this article we describe sensitivity models for the Einstein
Telescope and investigate potential limits imposed by fundamental noise
sources. A special focus is set on evaluating the frequency band below 10Hz
where a complex mixture of seismic, gravity gradient, suspension thermal and
radiation pressure noise dominates. We develop the most accurate sensitivity
model, referred to as ET-D, for a third-generation detector so far, including
the most relevant fundamental noise contributions.Comment: 13 pages, 7 picture
Calibration and sensitivity of the Virgo detector during its second science run
The Virgo detector is a kilometer-length interferometer for gravitational
wave detection located near Pisa (Italy). During its second science run (VSR2)
in 2009, six months of data were accumulated with a sensitivity close to its
design. In this paper, the methods used to determine the parameters for
sensitivity estimation and gravitational wave reconstruction are described. The
main quantities to be calibrated are the frequency response of the mirror
actuation and the sensing of the output power. Focus is also put on their
absolute timing. The monitoring of the calibration data as well as the
parameter estimation with independent techniques are discussed to provide an
estimation of the calibration uncertainties. Finally, the estimation of the
Virgo sensitivity in the frequency-domain is described and typical
sensitivities measured during VSR2 are shown.Comment: 30 pages, 23 figures, 1 table. Published in Classical and Quantum
Gravity (CQG), Corrigendum include
Scientific Potential of Einstein Telescope
Einstein gravitational-wave Telescope (ET) is a design study funded by the
European Commission to explore the technological challenges of and scientific
benefits from building a third generation gravitational wave detector. The
three-year study, which concluded earlier this year, has formulated the
conceptual design of an observatory that can support the implementation of new
technology for the next two to three decades. The goal of this talk is to
introduce the audience to the overall aims and objectives of the project and to
enumerate ET's potential to influence our understanding of fundamental physics,
astrophysics and cosmology.Comment: Conforms to conference proceedings, several author names correcte
Scientific Objectives of Einstein Telescope
The advanced interferometer network will herald a new era in observational
astronomy. There is a very strong science case to go beyond the advanced
detector network and build detectors that operate in a frequency range from 1
Hz-10 kHz, with sensitivity a factor ten better in amplitude. Such detectors
will be able to probe a range of topics in nuclear physics, astronomy,
cosmology and fundamental physics, providing insights into many unsolved
problems in these areas.Comment: 18 pages, 4 figures, Plenary talk given at Amaldi Meeting, July 201
Sensitivity to Gravitational Waves from Compact Binary Coalescences Achieved during LIGO's Fifth and Virgo's First Science Run
We summarize the sensitivity achieved by the LIGO and Virgo gravitational
wave detectors for compact binary coalescence (CBC) searches during LIGO's
fifth science run and Virgo's first science run. We present noise spectral
density curves for each of the four detectors that operated during these
science runs which are representative of the typical performance achieved by
the detectors for CBC searches. These spectra are intended for release to the
public as a summary of detector performance for CBC searches during these
science runs.Comment: 12 pages, 5 figure
- …