2,257 research outputs found
A method for defining down-wind evacuation areas for transportation accidents involving toxic propellant spills
Evacuation areas for accidental spills of toxic propellants along rail and highway shipping routes are defined to help local authorities reduce risks to people from excessive vapor concentrations. These criteria along with other emergency information are shown in propellant spill cards. The evacuation areas are based on current best estimates of propellant evaporation rates from various areas of spill puddles. These rates are used together with a continuous point-source, bi-normal model of plume dispersion. The rate at which the toxic plume disperses is based on a neutral atmospheric condition. This condition, which results in slow plume dispersion, represents the widest range of weather parameters which could occur during the day and nighttime periods. Evacuation areas are defined by the ground level boundaries of the plume within which the concentrations exceed the toxic Threshold Limit Value (TLV) or in some cases the Emergency Exposure Limit (EEL)
Fine particulate capture device
To capture fine particulate matter in a gas such as air, a dielectric fluid is directed to the center of whichever face of a rotating disc is exposed to the air flow. The disc is comprised of two or more segments which bear opposite electrostatic potentials. As the dielectric fluid is centrifuged towards the periphery of the rotating disc, the fluid becomes charged to the same potential as the segment over which it is passing. Particulate matter is attracted to the charged segment and is captured by the fluid. The fluid then carries the captured particulate matter to a collection device such as a toroidal container disposed around the periphery of the disc. A grounded electrically-conductive ring may be disposed at the outer periphery of the disc to neutralize the captured particles and the fluid before they enter the container
Flight/ground sample comparison relating to flight experiment M552, exothermic brazing
Comparisons were made between Skylab and ground-based specimens of nickel and stainless steel which were vacuum brazed using silver-copper-lithium alloy with various joint configurations. It was established that the absence of gravity greatly extends the scope of brazing since capillary flow can proceed without gravity interference. There was also evidence of enhanced transport, primarily in that liquid silver copper alloy dissolves nickel to a much greater extent in the zero gravity environment
Histologic, Immunohistochemical and Morphometric Study of the Mucosa of the total gastric antrum in Patients with carcinoma of the stomach.
Transfer of autocollimator calibration for use with scanning gantry profilometers for accurate determination of surface slope and curvature of state of the art x ray mirrors
X ray optics, desired for beamlines at free electron laser and diffraction limited storage ring x ray light sources, must have almost perfect surfaces, capable of delivering light to experiments without significant degradation of brightness and coherence. To accurately characterize such optics at an optical metrology lab, two basic types of surface slope profilometers are used the long trace profilers LTPs and nanometer optical measuring NOM like angular deflectometers, based on electronic autocollimator AC ELCOMAT 3000. The inherent systematic errors of the instrument s optical sensors set the principle limit to their measuring performance. Where autocollimator of a NOM like profiler may be calibrated at a unique dedicated facility, this is for a particular configuration of distance, aperture size, and angular range that does not always match the exact use in a scanning measurement with the profiler. Here we discuss the developed methodology, experimental set up, and numerical methods of transferring the calibration of one reference AC to the scanning AC of the Optical Surface Measuring System OSMS , recently brought to operation at the ALS Xray Optics Laboratory. We show that precision calibration of the OSMS performed in three steps, allows us to provide high confidence and accuracy low spatial frequency metrology and not print into measurements the inherent systematic error of tool in use. With the examples of the OSMS measurements with a state of the art x ray aspherical mirror, available from one of the most advanced vendors of X ray optics, we demonstrate the high efficacy of the developed calibration procedure. The results of our work are important for obtaining high reliability data, needed for sophisticated numerical simulations of beamline performance and optimization of beamline usage of the optics. This work was supported by the U. S. Department of Energy under contract number DE AC02 05CH1123
A Robust and Universal Metaproteomics Workflow for Research Studies and Routine Diagnostics Within 24 h Using Phenol Extraction, FASP Digest, and the MetaProteomeAnalyzer
The investigation of microbial proteins by mass spectrometry (metaproteomics) is a key technology for simultaneously assessing the taxonomic composition and the functionality of microbial communities in medical, environmental, and biotechnological applications. We present an improved metaproteomics workflow using an updated sample preparation and a new version of the MetaProteomeAnalyzer software for data analysis. High resolution by multidimensional separation (GeLC, MudPIT) was sacrificed to aim at fast analysis of a broad range of different samples in less than 24 h. The improved workflow generated at least two times as many protein identifications than our previous workflow, and a drastic increase of taxonomic and functional annotations. Improvements of all aspects of the workflow, particularly the speed, are first steps toward potential routine clinical diagnostics (i.e., fecal samples) and analysis of technical and environmental samples. The MetaProteomeAnalyzer is provided to the scientific community as a central remote server solution at www.mpa.ovgu.de.Peer Reviewe
Coherent oscillations in a Cooper-pair box
This paper is devoted to an analysis of the experiment by Nakamura {\it et
al.} (Nature {\bf 398}, 786 (1999)) on the quantum state control in Josephson
junctions devices. By considering the relevant processes involved in the
detection of the charge state of the box and a realistic description of the
gate pulse we are able to analyze some aspects of the experiment (like the
amplitude of the measurement current) in a quantitative way
- …