Lightweight stiffened panels : mechanical characterization of emerging fabrication technologies

Tese de doutoramento. Engenharia Mecânica. Faculdade de Engenharia. Universidade do Porto. 200

The contour method for residual stress determination applied to an AA6082-T6 friction stir butt weld

Residual stresses parallel to the welding direction on a cross-section of a 3 mm thick friction stir butt-welded aluminium alloy AA6082-T6 plate were determined using the contour method. This is a destructive relaxation based measurement technique capable of determining the full- eld residual stresses perpendicular to a plane of interest. A wire electro discharge machining cut was performed revealing the plane of interest. The residual stresses present before the straight cut lead to a deformed cutting plane. Then, a coordinate measuring machine was used to acquire the cutting plane shape of both plate halves after the cut. A data reduction scheme for noise and error elimination was used. The measured deformation was applied to a linear elastic nite elements model considering the real specimen geometry. A full contour map of longitudinal residual stresses on a weld cross section was determined in this way, revealing detailed information on the residual stress distribution in the inside of a friction stir weld, especially in the nugget zone. A typical M-shape, usually described for the residual stress distribution in friction stir welds, was found. The maximum residual stresses are below the yield strength of the material in the shoulder region and, outside of the welding region, low tensile and compressive residual stresses are responsible for the necessary stress equilibrium on the plane of interest. A comparison was made with the established incremental hole drilling technique on an equivalent plate for validation and good agreement of both techniques was obtained. The distribution, as well as the magnitude of the residual stresses measured by both techniques, is very similar, thus validating both the experimental and numerical procedures used for the contour method application, which is presented and discussed in the paper.The present work was partially funded by the project PTDC/EME-TME/66362/2006 and PhD scholarship SFRH / BD / 41061 / 2007 of the Portuguese Fundação para a Ciência e Tecnologia. Dr. P. Moreira acknowledges POPH - QREN-Tipologia 4.2 - Promotion of scientific employment funded by the ESF and MCTES. The help of José Fernando Rocha Almeida is also acknowledged

Pervasive gaps in Amazonian ecological research

Biodiversity loss is one of the main challenges of our time,1,2 and attempts to address it require a clear un derstanding of how ecological communities respond to environmental change across time and space.3,4 While the increasing availability of global databases on ecological communities has advanced our knowledge of biodiversity sensitivity to environmental changes,5–7 vast areas of the tropics remain understudied.8–11 In the American tropics, Amazonia stands out as the world’s most diverse rainforest and the primary source of Neotropical biodiversity,12 but it remains among the least known forests in America and is often underrepre sented in biodiversity databases.13–15 To worsen this situation, human-induced modifications16,17 may elim inate pieces of the Amazon’s biodiversity puzzle before we can use them to understand how ecological com munities are responding. To increase generalization and applicability of biodiversity knowledge,18,19 it is thus crucial to reduce biases in ecological research, particularly in regions projected to face the most pronounced environmental changes. We integrate ecological community metadata of 7,694 sampling sites for multiple or ganism groups in a machine learning model framework to map the research probability across the Brazilian Amazonia, while identifying the region’s vulnerability to environmental change. 15%–18% of the most ne glected areas in ecological research are expected to experience severe climate or land use changes by 2050. This means that unless we take immediate action, we will not be able to establish their current status, much less monitor how it is changing and what is being lostinfo:eu-repo/semantics/publishedVersio

Pervasive gaps in Amazonian ecological research

Biodiversity loss is one of the main challenges of our time,1,2 and attempts to address it require a clear understanding of how ecological communities respond to environmental change across time and space.3,4 While the increasing availability of global databases on ecological communities has advanced our knowledge of biodiversity sensitivity to environmental changes,5,6,7 vast areas of the tropics remain understudied.8,9,10,11 In the American tropics, Amazonia stands out as the world's most diverse rainforest and the primary source of Neotropical biodiversity,12 but it remains among the least known forests in America and is often underrepresented in biodiversity databases.13,14,15 To worsen this situation, human-induced modifications16,17 may eliminate pieces of the Amazon's biodiversity puzzle before we can use them to understand how ecological communities are responding. To increase generalization and applicability of biodiversity knowledge,18,19 it is thus crucial to reduce biases in ecological research, particularly in regions projected to face the most pronounced environmental changes. We integrate ecological community metadata of 7,694 sampling sites for multiple organism groups in a machine learning model framework to map the research probability across the Brazilian Amazonia, while identifying the region's vulnerability to environmental change. 15%–18% of the most neglected areas in ecological research are expected to experience severe climate or land use changes by 2050. This means that unless we take immediate action, we will not be able to establish their current status, much less monitor how it is changing and what is being lost

A contribution to the study of fatigue of riveted lap joints

Dissertação apresentada para obtenção do grau de Mestre em Engenharia Mecânica, na Faculdade de Engenharia da Universidade do Porto, sob a orientação dos Professores Paulo M.S.T. de Castro e Artur Portel

The contour method for residual stress determination applied to an AA6082-T6 friction stir butt weld

Residual stresses parallel to the welding direction on a cross-section of a 3 mm thick friction stir butt-welded aluminum alloy AA6082-T6 plate were determined using the contour method. A full contour map of longitudinal residual stresses on a weld cross section was determined in this way, revealing detailed information on the residual stress distribution in the inside of a friction stir weld, especially in the nugget zone. The typical M-shape, usually described for the residual stress distribution in friction stir welds, was found. The maximum residual stresses are below the yield strength of the material in the shoulder region and, outside of the welding region, low tensile and compressive residual stresses are responsible for the necessary stress equilibrium on the plane of interest. A comparison was made with the established incremental hole drilling technique on an equivalent plate for validation and good agreement of both techniques was obtained. The distribution, as well as the magnitude of the residual stresses measured by both techniques, is very similar, thus validating both the experimental and numerical procedures used for the contour method application, presented and discussed in the present paper.The present work was partially funded by the project PTDC/EME-TME/66362/2006 and PhD scholarship SFRH / BD/ 41061 / 2007 of the Portuguese Fundação para a Ciência e Tecnologia. Dr. P. Moreira acknowledges POPH – QREN Tipologia 4.2 -Promotion of scientific employment funded by the ESF and MCTES. The help of José Fernando Rocha Almeida is acknowledged. The interesting and helpful discussions during the ECRS 8 conference are also acknowledged

Stress intensity factor evaluation for central oriented cracks by stress dead‐zone concept

The concept of the stress dead zone (SDZ) at the crack vicinity of a plate submitted to a uniform tensile condition is key in the simplification of fracture characterization, in particular, in the calculation of the stress intensity factor (SIF). The stress field close to a crack face can be negligible in any structure, and thus, the corresponding region would be discarded from the initial structural component contributing to suppress the crack tip singularity. The computation of the Griffith compliance method based on disregarding this area can thereby be done with simple analytical formulations following linear elastic fracture mechanics principles. In this study, the SDZ concept was considered, together with the compliance function, to formulate the SIF analytical solution