LHC Superconducting Dipole Production Follow-up: Results of Audit on QA Aspects in Industry

The manufacturing of the 1232 Superconducting Main Dipoles for LHC is under way at three European Contractors: Alstom-Jeumont (Consortium), Ansaldo Superconduttori Genova and Babcock Noell Nuclear. The manufacturing is proceeding in a very satisfactory way and in March 2005 the mid production was achieved. To intercept eventually âﾜweak pointsâ of the production process still present and in order to make a check of the Quality Assurance and Control in place for the series production, an Audit action was launched by CERN during summer-fall 2004. Aspects like: completion of Production and Quality Assurance documentation, structure of QC Teams, traceability, calibration and maintenance for tooling, incoming components inspections, were checked during a total of seven visits at the five different production sites. The results of the Audit in terms of analysis of âﾜsystematicâ and âﾜrandomâ problems encountered as well as corrective actions requested are presented

Conceptual Design of Superferric Magnets for PS2

We analyze feasibility and cost of a superferric magnet design for the PS2, the 50 GeV ring that should replace the PS in the CERN injector chain. Specifically, we provide the conceptual design of dipole and quadrupoles, including considerations on cryogenics and powering. The magnets have warm iron yoke, and cryostated superconducting coils embedded in the magnet, which reduces AC loss at cryogenic temperature. The superconductor has large operating margin to endure beam loss and operating loads over a long period of time. Although conservative, and without any critical dependence on novel technology developments, this superconducting option appears to be attractive as a low-power alternative to the normal-conducting magnets that are the present baseline for the PS2 design. In addition it provides flexibility in the selection of flat-top duration at no additional cost

Differential cartilaginous tissue formation by human synovial membrane, fat pad, meniscus cells and articular chondrocytes

Objective: To identify an appropriate cell source for the generation of meniscus substitutes, among those which would be available by arthroscopy of injured knee joints. Methods: Human inner meniscus cells, fat pad cells (FPC), synovial membrane cells (SMC) and articular chondrocytes (AC) were expanded with or without specific growth factors (Transforming growth factor-betal, Fibroblast growth factor-2 and Plate let-derived growth factor bb, TFP) and then induced to form three-dimensional cartilaginous tissues in pellet cultures, or using a hyaluronan-based scaffold (Hyaff(R)-11), in culture or in nude mice. Human native menisci were assessed as reference. Results: Cell expansion with TFP enhanced glycosaminoglycan (GAG) deposition by all cell types (up to 4.1-fold) and messenger RNA expression of collagen type II by FPC and SMC (up to 472-fold) following pellet culture. In all models, tissues generated by AC contained the highest fractions of GAG (up to 1.9 were positively stained for collagen type II (specific of the inner avascular region of meniscus), type IV (mainly present in the outer vascularized region of meniscus) and types I, III and VI (common to both meniscus regions). Instead, inner meniscus, FPC and SMC developed tissues containing negligible GAG and no detectable collagen type II protein. Tissues generated by AC remained biochemically and phenotypically stable upon ectopic implantation. Conclusions: Under our experimental conditions, only AC generated tissues containing relevant amounts of GAG and with cell phenotypes compatible with those of the inner and outer meniscus regions. Instead, the other investigated cell sources formed tissues resembling only the outer region of meniscus. It remains to be determined whether grafts based on AC will have the ability to reach the complex structural and functional organization typical of meniscus tissue. (C) 2006 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights rese

Quality Control Techniques Applied to the Large Scale Production of Superconducting Dipole Magnets for LHC

The LHC accelerator, under construction at CERN, is characterized by the use on a large scale of high field superconducting dipoles: the 27-km ring requires 1232 15-m long dipole magnets designed for a peak field of 9 T. The coils are wound with Rutherford-type cable based on copper-stabilized Nb-Ti superconductors and will be operated at 1.9 K in pressurized superfluid helium. The challenge that had to be faced has been an efficient, cost-effective and reproducible mass production to very tight tolerances: the field quality must be better than 10-4 and the geometry of the cold bore tube and magnet controlled to 0.1 mm over the whole length, any deviation being liable to induce delays and significant cost increase. This paper presents the main methods and tools chosen to face successfully this challenge: some methods were foreseen in the technical specification, others were implemented based on the experience gained in several years of fabrication

LEP1 operation, 1989-1995

In October 1995, the last run foreseen for dedicated Z production at CERN was performed in LEP, thereby bringing to a close the first phase of operation of the machine. A total luminosity of 200 pb-1 has been delivered to each of the four experiments, which together have recorded the decays of over 20 millions Zs. Machine performance has increased to the extent that a good weekend in 1995 saw as much luminosity delivered as in the whole of 1989. This improvement has been made possible by a combination of several things. Over and above general operational expertise, special care went into the treatment and stabilisation of the closed orbit in order to obtain reproducible high performances with vertical beam-beam tune shifts exceeding values of xy = 0.04. Both Pretzel and Bunch Train schemes have been introduced to double the number of bunches, and high-tune optics have been developed to produce low transverse emittances which allow operation at the beam-beam limit throughout physics runs. Included in the integrated luminosity are data taken off the peak of the Z resonance, to allow precise determination of the mass and width of this particle. Accurate measurements of the beam energy during these runs have brought to the fore some unusual effects

Development and Coil Fabrication Test of the Nb3Sn Dipole Magnet PRESCA2

n/

The SPS as accelerator of Pb82+^{82+} ions

In 1994 the CERN SPS was used for the first time to accelerate fully stripped ions of the Pb208 isotope from the equivalent proton momentum of 13 GeV/c to 400 GeV/c. In the CERN PS, which was used as injector, the lead was accelerated as Pb53+ ions and then fully stripped in the transfer line from PS to SPS. The radio frequency swing which is needed in order to keep the synchronism during acceleration is too big to have the SPS cavities deliver enough voltage for all frequencies. For that reason a new technique of fixed frequency acceleration was used. With this technique up to 70% of the injected beam could be captured and accelerated up to the extraction energy, the equivalent of 2.2 1010 charges. The beam was extracted over a 5 sec. long spill and was then delivered to different experiments at the same time

The SPS as lead-ion accelerator

In 1995 the CERN SPS was used during two months to accelerate fully stripped ions of the Pb208 isotope from the equivalent proton momentum of 13 GeV/c to 400 GeV/c. The radio frequency swing which is needed in order to keep the synchronism during acceleration is too big to have the SPS cavities deliver enough voltage for all frequencies. In a first stage, the beam is accelerated from 13 GeV/c to 26 GeV/c using the fixed frequency mode. During this stage the beam is grouped in four 2msec batches, separated by 3msec holes during which the frequency is changed in order to keep synchronism. At 26 GeV the beams are de-bunched and recaptured in order to fill the 3msec holes. From there on the lead ions are then accelerated up to 400 GeV/c with the normal frequency program. The de-bunching and recapture at 26 GeV improved the effective spill at extraction by a factor of three. Intensities up to 3.9 1010 charges could be obtained at 400 GeV/c. The total efficiency of the two RF captures was 64%