Cold storage using phase change material in refrigerated display cabinets: experimental investigation

Refrigerated display cabinets are the main energy consumers in supermarkets. Cold thermal energy storage (CTES) using phase change materials (PCM) can significantly reduce temperature variations in a display cabinet during loading of warm items, defrost cycles or power outages. This contributes to reduced loss in product quality and less food being wasted. With an increasing share of intermittent renewables in the power grid, PCM-enhanced systems benefit from low-cost electricity during periods with low demand. Stored excess cooling can be later used during periods with high demand. A CTES prototype was developed using water as PCM integrated in an evaporator. This system was experimentally compared to a reference case not using the PCM capabilities. The results show the potential for PCM-CTES to consistently keep the cabinet air temperature low, thus prolonging shelf life and product quality. Charged PCM-CTES systems provide cooling for several hours after the main evaporator is deactivated. Keywords: Refrigerated Display Cabinet, Thermal Energy Storage, Cold Storage, Phase Change Material, Supermarket Refrigeration, Defrost Cycle.acceptedVersio

Linking Sediment Gas Storage to the Methane Dynamics in a Shallow Freshwater Reservoir

Freshwater reservoirs are globally relevant sources of the greenhouse gas methane. Organic matter rich sediments are hot spots of methane production and can store large amounts of methane dissolved in porewater and as free gas. Yet, in situ data on the gas storage as free gas (bubbles) in freshwater sediments are scarce. Here, an acoustic approach was tested and used to map the gas content in the sediment of a shallow temperate reservoir. The sediment gas storage was linked to the methane budget obtained from almost 2 years of in situ monitoring. The emission fluxes were dominated by ebullition and degassing at the reservoir outlet, which combined accounted for 93% of the total methane emissions. 66% of the ebullition variability was explained by a combination of environmental parameters. Mappings of sediment gas content using echo sounder surveys revealed the accumulation of free gas in regions of elevated sediment deposition. Temporally, the gas storage in the sediment was related to methane emissions, in which a period of intensified emissions resulted in a reduction of sediment gas storage. The sediment could store an equivalent of 4 to 13 days of accumulated potential methane production, which could supply the mean ebullition flux for more than 2 months. We suggest that sediment gas storage plays an important role in buffering and modulating methane emissions in aquatic systems and need to be accounted for in process-based models

Quantity, composition, and source of sediment collected in sediment traps along the fringing coral reef off Molokai, Hawaii

This paper is not subject to U.S. copyright. The definitive version was published in Marine Pollution Bulletin 52 (2006): 1034-1047, doi:10.1016/j.marpolbul.2006.01.008.Sediment traps were used to evaluate the frequency, cause, and relative intensity of sediment mobility/resuspension along the fringing coral reef off southern Molokai (February 2000–May 2002). Two storms with high rainfall, floods, and exceptionally high waves resulted in sediment collection rates > 1000 times higher than during non-storm periods, primarily because of sediment resuspension by waves. Based on quantity and composition of trapped sediment, floods recharged the reef flat with land-derived sediment, but had a low potential for burying coral on the fore reef when accompanied by high waves. The trapped sediments have low concentrations of anthropogenic metals. The magnetic properties of trapped sediment may provide information about the sources of land-derived sediment reaching the fore reef. The high trapping rate and low sediment cover indicate that coral surfaces on the fore reef are exposed to transient resuspended sediment, and that the traps do not measure net sediment accumulation on the reef surface

Sources of land-derived runoff to a coral reef-fringed embayment identified using geochemical tracers in nearshore sediment traps

This paper is not subject to U.S. copyright. The definitive version was published in Estuarine, Coastal and Shelf Science 85 (2009): 459-471, doi:10.1016/j.ecss.2009.09.014.Geochemical tracers, including Ba, Co, Th, 7Be, 137Cs and 210Pb, and magnetic properties were used to characterize terrestrial runoff collected in nearshore time-series sediment traps in Hanalei Bay, Kauai, during flood and dry conditions in summer 2006, and to fingerprint possible runoff sources in the lower watershed. In combination, the tracers indicate that runoff during a flood in August could have come from cultivated taro fields bordering the lower reach of the river. Land-based runoff associated with summer floods may have a greater impact on coral reef communities in Hanalei Bay than in winter because sediment persists for several months. During dry periods, sediment carried by the Hanalei River appears to have been mobilized primarily by undercutting of low 7Be, low 137Cs riverbanks composed of soil weathered from tholeiitic basalt with low Ba and Co concentrations. Following a moderate rainfall event in September, high 7Be sediment carried by the Hanalei River was probably mobilized by overland flow in the upper watershed. Ba-desorption in low-salinity coastal water limited its use to a qualitative runoff tracer in nearshore sediment. 210Pb had limited usefulness as a terrestrial tracer in the nearshore due to a large dissolved oceanic source and scavenging onto resuspended bottom sediment. 210Pb-scavenging does, however, illustrate the role resuspension could play in the accumulation of particle-reactive contaminants in nearshore sediment. Co and 137Cs were not affected by desorption or geochemical scavenging and showed the greatest potential as quantitative sediment provenance indicators in material collected in nearshore sediment traps

Acceleration of dormant storage effects to address the reliability of silicon surface micromachined Micro-Electro-Mechanical Systems (MEMS).

Qualification of microsystems for weapon applications is critically dependent on our ability to build confidence in their performance, by predicting the evolution of their behavior over time in the stockpile. The objective of this work was to accelerate aging mechanisms operative in surface micromachined silicon microelectromechanical systems (MEMS) with contacting surfaces that are stored for many years prior to use, to determine the effects of aging on reliability, and relate those effects to changes in the behavior of interfaces. Hence the main focus was on 'dormant' storage effects on the reliability of devices having mechanical contacts, the first time they must move. A large number ({approx}1000) of modules containing prototype devices and diagnostic structures were packaged using the best available processes for simple electromechanical devices. The packaging processes evolved during the project to better protect surfaces from exposure to contaminants and water vapor. Packages were subjected to accelerated aging and stress tests to explore dormancy and operational environment effects on reliability and performance. Functional tests and quantitative measurements of adhesion and friction demonstrated that the main failure mechanism during dormant storage is change in adhesion and friction, precipitated by loss of the fluorinated monolayer applied after fabrication. The data indicate that damage to the monolayer can occur at water vapor concentrations as low as 500 ppm inside the package. The most common type of failure was attributed to surfaces that were in direct contact during aging. The application of quantitative methods for monolayer lubricant analysis showed that even though the coverage of vapor-deposited monolayers is generally very uniform, even on hidden surfaces, locations of intimate contact can be significantly depleted in initial concentration of lubricating molecules. These areas represent defects in the film prone to adsorption of water or contaminants that can cause movable structures to adhere. These analysis methods also indicated significant variability in the coverage of lubricating molecules from one coating process to another, even for identical processing conditions. The variability was due to residual molecules left in the deposition chamber after incomplete cleaning. The coating process was modified to result in improved uniformity and total coverage. Still, a direct correlation was found between the resulting static friction behavior of MEMS interfaces, and the absolute monolayer coverage. While experimental results indicated that many devices would fail to start after aging, the modeling approach used here predicted that all the devices should start. Adhesion modeling based upon values of adhesion energy from cantilever beams is therefore inadequate. Material deposition that bridged gaps was observed in some devices, and potentially inhibits start-up more than the adhesion model indicates. Advances were made in our ability to model MEMS devices, but additional combined experimental-modeling studies will be needed to advance the work to a point of providing predictive capability. The methodology developed here should prove useful in future assessments of device aging, however. Namely, it consisted of measuring interface properties, determining how they change with time, developing a model of device behavior incorporating interface behavior, and then using the age-aware interface behavior model to predict device function

Modelica-based modelling of heat pump-assisted apple drying for varied drying temperatures and bypass ratios

publishedVersio

Design of a CO2 heat pump drier with dynamic modelling tools

acceptedVersio