Refractory metals as structural materials for fusion high heat flux components

Tungsten is the favoured armour material for plasma facing components for future fusion reactors, but studies examining the use of tungsten or other refractory metals in the underlying cooled structures have historically excluded them, leaving current concepts heavily dependent on copper alloys such as copper chrome zirconium. This paper first outlines the challenge of selecting an appropriate alternative material for this application, with reference to historical selection methodology and design solutions, and then re-examines the use of refractory metals in the light of current design priorities and manufacturing techniques. The rationale for considering refractory alloys as structural materials is discussed, showing how this is the result of relatively small changes to the logic previously applied, with a greater emphasis on high temperature operation, a re-evaluation of current costs, a relaxation of absolute activation limits, and the availability of advanced manufacturing techniques such as additive manufacturing. A set of qualitative and quantitative assessment criteria are proposed, drawing on the requirements detailed in the first section; including thermal and mechanical performance, radiation damage tolerance, manufacturability, and cost and availability. Considering these criteria in parallel rather than sequence gives a less binary approach to material selection and instead provides a strengths and weaknesses based summary from which more nuanced conclusions can be drawn. Data on relevant material properties for a range of candidate materials, including elemental refractory metals and a selection of related alloys are gathered from a range of sources and collated using a newly developed set of tools written in the python language. These tools are then used to apply the aforementioned assessment criteria and display the results. The lack of relevant data for a number of promising materials is highlighted, and although a conclusive best material cannot be identified, refractory alloys in general are proposed as worthy of further investigation

On the mechanisms governing gas penetration into a tokamak plasma during a massive gas injection

A new 1D radial fluid code, IMAGINE, is used to simulate the penetration of gas into a tokamak plasma during a massive gas injection (MGI). The main result is that the gas is in general strongly braked as it reaches the plasma, due to mechanisms related to charge exchange and (to a smaller extent) recombination. As a result, only a fraction of the gas penetrates into the plasma. Also, a shock wave is created in the gas which propagates away from the plasma, braking and compressing the incoming gas. Simulation results are quantitatively consistent, at least in terms of orders of magnitude, with experimental data for a D 2 MGI into a JET Ohmic plasma. Simulations of MGI into the background plasma surrounding a runaway electron beam show that if the background electron density is too high, the gas may not penetrate, suggesting a possible explanation for the recent results of Reux et al in JET (2015 Nucl. Fusion 55 093013)

Modelling of the effect of ELMs on fuel retention at the bulk W divertor of JET

Effect of ELMs on fuel retention at the bulk W target of JET ITER-Like Wall was studied with multi-scale calculations. Plasma input parameters were taken from ELMy H-mode plasma experiment. The energetic intra-ELM fuel particles get implanted and create near-surface defects up to depths of few tens of nm, which act as the main fuel trapping sites during ELMs. Clustering of implantation-induced vacancies were found to take place. The incoming flux of inter-ELM plasma particles increases the different filling levels of trapped fuel in defects. The temperature increase of the W target during the pulse increases the fuel detrapping rate. The inter-ELM fuel particle flux refills the partially emptied trapping sites and fills new sites. This leads to a competing effect on the retention and release rates of the implanted particles. At high temperatures the main retention appeared in larger vacancy clusters due to increased clustering rate

The effect of beryllium oxide on retention in JET ITER-like wall tiles

Preliminary results investigating the microstructure, bonding and effect of beryllium oxide formation on retention in the JET ITER-like wall beryllium tiles, are presented. The tiles have been investigated by several techniques: Scanning Electron Microscopy (SEM) equipped with Energy Dispersive X-ray (EDX), Transmission Electron microscopy (TEM) equipped with EDX and Electron Energy Loss Spectroscopy (EELS), Raman Spectroscopy and Thermal Desorption Spectroscopy (TDS). This paper focuses on results from melted materials of the dump plate tiles in JET. From our results and the literature, it is concluded, beryllium can form micron deep oxide islands contrary to the nanometric oxides predicted under vacuum conditions. The deepest oxides analyzed were up to 2-micron thicknesses. The beryllium Deuteroxide (BeOxDy) bond was found with Raman Spectroscopy. Application of EELS confirmed the oxide presence and stoichiometry. Literature suggests these oxides form at temperatures greater than 700 °C where self-diffusion of beryllium ions through the surface oxide layer can occur. Further oxidation is made possible between oxygen plasma impurities and the beryllium ions now present at the wall surface. Under Ultra High Vacuum (UHV) nanometric Beryllium oxide layers are formed and passivate at room temperature. After continual cyclic heating (to the point of melt formation) in the presence of oxygen impurities from the plasma, oxide growth to the levels seen experimentally (approximately two microns) is proposed. This retention mechanism is not considered to contribute dramatically to overall retention in JET, due to low levels of melt formation. However, this mechanism, thought the result of operation environment and melt formation, could be of wider concern to ITER, dependent on wall temperatures

Interpretative and predictive modelling of Joint European Torus collisionality scans

Transport modelling of Joint European Torus (JET) dimensionless collisionality scaling experiments in various operational scenarios is presented. Interpretative simulations at a fixed radial position are combined with predictive JETTO simulations of temperatures and densities, using the TGLF transport model. The model includes electromagnetic effects and collisions as well as □(→┬E ) X □(→┬B ) shear in Miller geometry. Focus is on particle transport and the role of the neutral beam injection (NBI) particle source for the density peaking. The experimental 3-point collisionality scans include L-mode, and H-mode (D and H and higher beta D plasma) plasmas in a total of 12 discharges. Experimental results presented in (Tala et al 2017 44th EPS Conf.) indicate that for the H-mode scans, the NBI particle source plays an important role for the density peaking, whereas for the L-mode scan, the influence of the particle source is small. In general, both the interpretative and predictive transport simulations support the experimental conclusions on the role of the NBI particle source for the 12 JET discharges