140 research outputs found
Recommended from our members
FE Investigation of Perforated Sections with Standard and Non-Standard Web Opening Configurations and Sizes
The objective of this work is to investigate and compare, through an analytical study, the behaviour of perforated steel beams with different shape configurations and sizes of web openings. In this investigation the āVierendeelā failure mechanisms of steel beams with web openings are examined through a Finite Element study. The shear and flexural failures of standard perforated sections are controlled mainly by the size (i.e. depth) of the web openings, whilst the āVierendeelā mechanism is primarily controlled by the critical length of the web openings. Three main categories of web opening shape configurations and sizes are considered in this work. Standard, non-standard and elongated web opening configurations are examined, each with three different opening sizes. Four Advanced UB beams are used in the investigation in order to cover a range of sections and demonstrate the main differences in behaviour. The results of this comprehensive FE study are presented and include the position of plastic hinges, the critical opening length of perforated steel sections and the āVierendeelā parameters. The yield patterns and the failure modes do not differ dramatically. The results of this study are considered as relevant for practical applications as: (i) the reduction of the moment capacities of the tee-sections due to combination of axial and shear forces is smaller compared to the previous conservative linear interaction formula, and (ii) the formation of the initial plastic hinges at the low moment side (LMS) of the top tee-sections of the web openings does not usually cause failure, meaning that the beams can continue to carry additional load until all four plastic hinges are formed in the vicinity of the web openings and a āVierendeelā mechanism is fully established
Recommended from our members
Web buckling study of the behaviour and strength of perforated steel beams with different novel web opening shapes
This paper presents an experimental and analytical study on the behaviour of perforated steel beams with closely spaced web openings. Seven specimens including two typical cellular beams (i.e. circular web openings) and five perforated beams with novel web opening shapes were tested to investigate the failure mode and load strength of the web-post between two adjacent web openings. Fourteen numerical test specimens were developed and analysed by the finite element method and the results were compared with the full scale experiments. The effect of web opening spacing/web opening depth of web-posts was studied to investigate the effective āstrutā action of the web-post buckling. The effect of the web opening depth/web thickness was also studied to investigate the stability (slenderness) of the web-post subjected to vertical shear load. Two hundred and twenty-fine elastic-plastic finite element analyses were then employed in a comprehensive parametric study to propose an empirical formula which predicts the ultimate vertical shear load strength of web-posts formed from the particular web opening shapes. Perforated beams with standard circular, hexagonal and elongated web openings are mostly used nowadays. Various non-standard web opening shapes are introduced through this paper. These new pioneering web opening shapes improve the structural performance of the perforated beams when examined under the web-post buckling failure mode. In addition, the manufacturing procedure of these non-standard web openings show great advantage in comparison with the manufacturing way of the more popular perforated beams with circular web openings (i.e. cellular beams)
Recommended from our members
Finite Element Investigation on Web-Post Buckling of Perforated Steel Beams with Various Web Opening Shapes subjected under different shear-moment interaction
The current method of assessment is based on FE models which still lack computational efficiency and are restricted by a number of limitations. Therefore, this work aims at the feasibility of developing FE models which are applicable to deformation and strength prediction of full scale perforated steel beams. The main area of interest is the stability of the web-post under the combined effect of shear and compression, especially at the edge of the web openings, where the stabilizing effect of tension field action is less than that at the centre of the web-post
Recommended from our members
Experimental Study of Ultra Shallow Floor Beams (USFB) with Perforated Steel Sections
ABSTRACT: In modern building construction design, floor spans are becoming longer. Hence, steel framed structures have become more competitive when compared with traditional reinforced concrete framed buildings. In order to minimise the structural section of the composite sections, and for economic reasons, steel perforated beams are designed to act compositely with the floor slab. When the concrete slab lies within the steel flanges, as in the Ultra Shallow Floor Beam (USFB), there is an additional benefit when considering fire resistance. The aim of this study is to investigate the contribution of the concrete in composite cellular beams in the case where the concrete slab lies between the beam flanges of a steel section, when resisting vertical shear forces. The concrete between the flanges enhances the load-carrying capacity by providing a load path to transfer the shear force. Four specimens of steel-concrete composite beams with web openings in the steel section were tested in this study. One bare steel section with web openings was also tested as a comparison. This is the first such investigation of the failure mode under shear resistance (Vierendeel action) of the Ultra Shallow Floor Beam. In the test specimens, the web opening diameter is 76% of the beam depth, which is the largest currently available. This represents the worst case in terms of Vierendeel bending forces generated in the vicinity of the web openings. The smaller the hole is, the easier it is for the trapped concrete between the flanges to transfer shear across the opening. The results from the composite beam tests show a significant increase in shear resistance. The percentage of the shear capacity improvement of the particular case is presented herein as well as the failure mode of the composite beams. The shear enhancement demonstrated in this study has been utilised software that is used in design practice
Recommended from our members
Derivation of dynamic properties of steel perforated Ultra Shallow Floor Beams (USFBTD) via Finite Element modal analysis and experimental verification
In recent years, the incorporation of asymmetric perforated ultra shallow floor beams (USFBs) constructed from advanced UB and UC profile beams in various composite floor systems has been extensively considered in practice. To date, limited research effort has been devoted to the detailed investigation of the dynamic properties of USFBs. In this paper, modal analyses of detailed FE models of various USFBs commonly used in composite floor systems developed in ANSYS are conducted to extract their dynamical properties (i.e. natural frequencies and mode shapes). Furthermore, experimental data pertaining to the standard impact test is also considered to validate the accuracy of the aforementioned FE results. In particular, a six meter long USFB beam is subject to impulsive excitation by means of an appropriately instrumented hammer. The dynamic properties obtained by processing the recorded response signals compare well vis-a-vis the corresponding results from the FE modal analysis. Finally, effective properties of USFBs which can be readily used in the definition of beam elements of constant cross-section along their longitudinal direction are derived. This constitutes an important step to facilitate the analysis and design of USFBs against dynamic loads at the serviceability limit state using standard commercial structural analysis software
Recommended from our members
Shear Capacity of Perforated Concrete-Steel Ultra Shallow Floor Beams (USFB)
ABSTRACT : In modern building construction floor spans are becoming longer and one way of achieving this is to use composite beams. In order to minimize the structural depth of the composite sections, and to produce lighter members for economy reasons, steel perforated beams are designed to act compositely with the floor slab in an Ultra Shallow Floor Beam (USFB). In the USFB the concrete slab lies within the steel flanges and is connected through the web opening, providing enhanced longitudinal and vertical shear resistance. There is an additional benefit in increased fire resistance. The aim of this project is to investigate, through finite element simulations and suitable tests, the contribution of concrete in composite cellular beams in resisting vertical shear when the concrete slab lies between the flanges of the steel section. The concrete between the flanges provides the load path to transfer the shear force. For the computational approach to the problem, a three-dimensional Finite Element (FE) model was created, in which contact elements were implemented at the interface of the concrete and steel. In an earlier experimental study, four specimens of composite beams of similar concrete strength were tested under monotonic loading in order to produce reliable results. One specimen was from a lower grade of concrete and was tested in order to calibrate the shear resistance and the failure mode. One bare steel perforated section with web openings was also tested as a comparison. The comparison between the experimental and the computational results leads to useful conclusions. The results for the composite beams show a significant increase in shear resistance. The shear enhancement demonstrated in this study can now be used in design practice
Recommended from our members
Experimental study and analytical study of push-out shear tests in Ultra Shallow Floor Beams
The Ultra Shallow Floor Beam is a new type of composite floor beam fabricated by welding two highly asymmetric cellular tees together along the web and incorporating a concrete slab between the top and bottom flanges. The unique features of this system are circular and elongated web openings that allow tie-bars, building services and ducts passing through the structural depth of the beam. For the composite beam in bending, the longitudinal shear force is transferred by a unique shear mechanism which results from the special configuration of the beam, and shear connectors, if they are present. The work reported in this paper includes a total of 16 full-scale push-out tests aimed at investigating the longitudinal shear behaviour of these beams and the effects of additional shear connectors. A theoretical analysis was also performed to investigate the failure mechanism of the system
Recommended from our members
Applications of topology optimization in structural engineering: High-rise buildings and steel components
This study introduces applications of structural topology optimization to buildings and civil engineering structures. Topology optimization problems utilize the firmest mathematical basis, to account for improved weight-to-stiffness ratio and perceived aesthetic appeal of specific structural forms, enabling the solid isotropic material with penalization (SIMP) technique. Structural topology optimization is a technique for finding the optimum number, location and shape of āopeningsā within a given continuum subject to a series of loads and boundary conditions. Aerospace and automotive engineers routinely employ topology optimization and have reported significant structural performance gains as a result. Recently, designers of buildings and structures have also started investigating the use of topology optimization, for the design of efficient and aesthetically pleasing developments. This paper examines two examples of where topology optimization may be a useful design tool in civil/structural engineering in order to overcome the frontiers between civil engineers and engineers from other disciplines. The first example presents the optimized structural design of a geometrically complex high-rise structure and the optimal design of its architectural building shape. The second one focuses on the optimization and design of a perforated steel I-section beam, since such structural members are widely used nowadays in the vast majority of steel buildings and structures while they provide numerous advances. Conclusions are drawn regarding the potential benefits to the more widespread implementation of topology optimization within the civil/structural engineering industry
Recommended from our members
A Novel Optimised Inter-Locking Connection for Steel Modular Building Systems to Enable Re-Use
A new inter-module connection was developed, adopting structural topology optimisation (STO) and the inter-locking method of joining. The structural performance of the connection was assessed through a series of monotonic and cyclic FE analyses. Results revealed that the structural behaviour of the new connection was comparable to that of other inter-module joints in the literature, while managing to tackle their limitations by introducing both an easy-to-install and easy-to-disassemble configuration with promising opportunities for reuse, demonstrating that inter-locking joints can be worthy competitors for traditional means of attachment in the future of modular construction
- ā¦