Metallography of Al-Si Alloys with Alloying By Fe up to 1%

Metallographic analysis of aluminum-silicon alloys with different silicon content from 0 to 12% carried out. All alloys were differed in 2% by silicon amount from each other and all of them were additionally alloyed with iron in an amount of up to 1% in order to improve the technological properties in a die casting process. The paper shows the distribution of structural components of alloys made by electronic microscopy.     Keywords: aluminum-silicon alloys, metallography analysis, eutectic, structure, cast alloy, alloying, electron microscop

Lanthanum-Gallium Tantalate Crystals and their Electrophysical Characterization

Lanthanum-gallium tantalate single crystal (La3Ta0.5Ga5.5O14, langatate, LGT) is a perspective piezoe-lectric material as an active component of pressure sensors. An investigation of the growth conditions in-fluence (the growth atmosphere) on the electrophysical сharacterization of LGT, obtained in different at-mospheres (Ar, Ar + O2) was carried out. The frequency dependences of the relative dielectric constant (ε11/ε0) and of the admittance depend on the growth atmosphere. The langatate electrophysical сharacteri-zation in alternating electric fields were analyzed by means of the impedance spectr oscopy method. The behavior of short circuit currents in specimens of polar cuts of LGT single crystals with the same material electrodes without preliminary polarization is described. When you are citing the document, use the following link http://essuir.sumdu.edu.ua/handle/123456789/3628

Piezoelectric Characteristics of LiNbO3 Thin-film Heterostructures via Piezoresponse Force Microscopy

Electro-optic LiNbO3 thin films were deposited on Si(100) and Si(111) substrates using a radio-frequency magnetron sputtering process. The piezoelectric properties of the LiNbO3 films were investigated using the scanning probe microscopy in the piezoresponse mode. The obtained results show the high degree of grains orientation in polycrystalline structure. The piezoelectric modulus (dzz) was estimated to be 16 pm/V (for LiNbO3 / Si(100)) and 22 pm/V (for LiNbO3 / Si(111)) and the polarization about of 0.37 C·m – 2. These values are larger than those reported previously for LiNbO3 films. When you are citing the document, use the following link http://essuir.sumdu.edu.ua/handle/123456789/3366

Formation of the Electric Field Distribution in Thin Electro-Optic Layers for Precision Correction their Optical Characteristics

A method of making given field distribution within thin electro-optical layers by using narrow band electrodes placed at the same electric potential. A formula for electric field intensity produced by a single band electrode is obtained. Electric field modeling for different band electrode configurations is undertaken. It was shown, by applying piezoresponse force microscopy, that in case of highly inhomogeneous field the polarization of lithium niobate electro-optical film persisted only in the area above the band electrode. Lithium niobate, electro-optical structures, piezoresponse force microscopy, Computer simulation

Synthesis and Nanoscale Characterization of LiNbO3 Thin Films Deposited on Al2O3 Substrate by RF Magnetron Sputtering under Electric Field

LiNbO3 thin films were deposited on Al2O3 substrates by RF-magnetron sputtering with in-situ electric field to study the self-polarization effect. The films have been characterized crystallographically by x-ray diffraction, and morphologically by atomic force microscopy. The films contain crystallites of LiNbO3 with preferable orientation [012] along the normal to the Al2O3 substrate surface (012). Piezoresponse force microscopy was used to study vertical and lateral polarization direction in LiNbO3 thin films. The analysis of the histograms of vertical piezoresponse images allowed to reveal self-polarization effect in films. The local piezoelectric hysteresis performed on the nanometer scale indicates switching behavior of polarization for LiNbO3 thin film

Multi-spectral image processing for the measurement of a spatial temperature distribution on the surface of a laser-heated microscopic object

In this paper, we demonstrate that combining a laser heating (LH) system with a tandem acousto-optical tunable filter (TAOTF) allows us to measure the temperature distribution (TD) across a laser-heated microscopic specimen. Spectral image processing is based on one-dimensional (1D) non-linear least squares fitting of the Planck radiation function. It is applied for determining the temperature T at each point (x, y) of the specimen surface. It is shown that spectral image processing using the 1D non-linear least squares fitting allows measurement of the TD of the laser-heated microscopic specimen with higher precision and stability than those of the conventional linear least-squares fitting of the Wien approximation of Planck’s law.The Russian Science Foundation (project #17-12-01535) financially supported the work

Formation of the Electric Field Distribution in Thin Electro-Optic Layers for Precision Correction their Optical Characteristics

A method of making given field distribution within thin electro-optical layers by using narrow band electrodes placed at the same electric potential. A formula for electric field intensity produced by a single band electrode is obtained. Electric field modeling for different band electrode configurations is undertaken. It was shown, by applying piezoresponse force microscopy, that in case of highly inhomogeneous field the polarization of lithium niobate electro-optical film persisted only in the area above the band electrode. Lithium niobate, electro-optical structures, piezoresponse force microscopy, Computer simulation

Ir–Re binary alloys under extreme conditions and their electrocatalytic activity in methanol oxidation

The formation of the hcp-Ir0.70Re0.30 alloy from the single-source precursor (NH4)2[Ir0.70Re0.30Cl6] upon heating in hydrogen atmosphere can be associated with the formation of two intermediates: a crystalline iridium-based intermediate and a fcc-structured alloy. Ir–Re alloys show lower thermal expansion coefficients and smaller compressibility in comparison with individual metals. The high-temperature high-pressure treatment of hcp-Ir0.70Re0.30 alloy enable us to probe the Ir–Re pressure dependent phase diagram. The miscibility gap between hcp and fcc alloys slightly shifts towards the rhenium side below 4 GPa. Above 4 GPa, the miscibility gap does not drift with pressure and narrows with compression. The electrocatalytic activity of Ir–Re alloys has been tested for methanol oxidation in acidic water solution. Ir–Re alloys show higher electrocatalytic activity in comparison with pure Ir and Re, which makes them perspective candidates for fuel cells application. The highest electrocatalytic activity has been obtained for the two-phase Ir0.85Re0.15 composition

Synthesis and Nanoscale Characterization of LiNbO3 Thin Films Deposited on Al2O3 Substrate by RF Magnetron Sputtering under Electric Field

LiNbO3 thin films were deposited on Al2O3 substrates by RF-magnetron sputtering with in-situ electric field to study the self-polarization effect. The films have been characterized crystallographically by x-ray diffraction, and morphologically by atomic force microscopy. The films contain crystallites of LiNbO3 with preferable orientation [012] along the normal to the Al2O3 substrate surface (012). Piezoresponse force microscopy was used to study vertical and lateral polarization direction in LiNbO3 thin films. The analysis of the histograms of vertical piezoresponse images allowed to reveal self-polarization effect in films. The local piezoelectric hysteresis performed on the nanometer scale indicates switching behavior of polarization for LiNbO3 thin film

Magnetic fields in supernova remnants and pulsar-wind nebulae

We review the observations of supernova remnants (SNRs) and pulsar-wind nebulae (PWNe) that give information on the strength and orientation of magnetic fields. Radio polarimetry gives the degree of order of magnetic fields, and the orientation of the ordered component. Many young shell supernova remnants show evidence for synchrotron X-ray emission. The spatial analysis of this emission suggests that magnetic fields are amplified by one to two orders of magnitude in strong shocks. Detection of several remnants in TeV gamma rays implies a lower limit on the magnetic-field strength (or a measurement, if the emission process is inverse-Compton upscattering of cosmic microwave background photons). Upper limits to GeV emission similarly provide lower limits on magnetic-field strengths. In the historical shell remnants, lower limits on B range from 25 to 1000 microGauss. Two remnants show variability of synchrotron X-ray emission with a timescale of years. If this timescale is the electron-acceleration or radiative loss timescale, magnetic fields of order 1 mG are also implied. In pulsar-wind nebulae, equipartition arguments and dynamical modeling can be used to infer magnetic-field strengths anywhere from about 5 microGauss to 1 mG. Polarized fractions are considerably higher than in SNRs, ranging to 50 or 60% in some cases; magnetic-field geometries often suggest a toroidal structure around the pulsar, but this is not universal. Viewing-angle effects undoubtedly play a role. MHD models of radio emission in shell SNRs show that different orientations of upstream magnetic field, and different assumptions about electron acceleration, predict different radio morphology. In the remnant of SN 1006, such comparisons imply a magnetic-field orientation connecting the bright limbs, with a non-negligible gradient of its strength across the remnant.Comment: 20 pages, 24 figures; to be published in SpSciRev. Minor wording change in Abstrac