Measurement of Creep Deformation across Welds in 316H Stainless Steel Using Digital Image Correlation

Spatially resolved measurement of creep deformation across weldments at high temperature cannot be achieved using standard extensometry approaches. In this investigation, a Digital Image Correlation (DIC) based system has been developed for long-term high-temperature creep strain measurement in order to characterise the material deformation behaviour of separate regions of a multi-pass weld. The optical system was sufficiently stable to allow a sequence of photographs to be taken suitable for DIC analysis of creep specimens tested at a temperature of 545 °C for over 2000 h. The images were analysed to produce local creep deformation curves from two cross-weld samples cut from contrasting regions of a multi-pass V-groove weld joining thick-section AISI Type 316H austenitic stainless steel. It is shown that for this weld, the root pass is the weakest region of the structure in creep, most likely due to the large number of thermal cycles it has experienced during the fabrication process. The DIC based measurement method offers improved spatial resolution over conventional methods and greatly reduces the amount of material required for creep characterisation of weldments

Dielectric relaxation dynamics of high-temperature piezoelectric polyimide copolymers

Polyimide co-polymers have been prepared based on different diamines as co-monomers: a diamine without CN groups and a novel synthesized diamine with two CN groups prepared by polycondensation reaction followed by thermal cyclodehydration. Dielectric spectroscopy measurements were performed and the dielectric complex function, ac conductivity and electric modulus of the co-polymers were investigated as a function of CN group content in the frequency range from 0.1 Hz to 107 Hz at temperatures from 25 to 260 °C. For all samples and temperatures above 150ºC, the dielectric constant increases with increasing temperature due to increaseing conductivity. The α-relaxation is just detected for the sample without CN groups, being this relaxation overlapped by the electrical conductivity contributions in the remaining samples. For the copolymer samples and the polymer with CN groups an important Maxwell-Wagner-Sillars contribution is detected. The mechanisms responsible for the dielectric relaxation, conduction process and electric modulus response have been discussed as a function of the CN groups content present in the samples.This work was supported by FEDER through the COMPETE Program and by the Portuguese Foundation for Science and Technology (FCT) in the framework of the Strategic Project PESTC/FIS/UI607/2011 and grants SFRH/BD/ 62507/2009 (A.C.L.) SFRH/BD/68499/2010 (C.M.C.). The authors also thank funding from “Matepro – Optimizing Materials and Processes”, ref. NORTE-07-0124-FEDER-000037”, co-funded by the “Programa Operacional Regional do Norte” (ON.2 – O Novo Norte), under the “Quadro de Referência Estratégico Nacional” (QREN), through the “Fundo Europeu de Desenvolvimento Regional” (FEDER). RSS acknowledge the support of the Spanish Ministry of Economy and Competitiveness through the project MAT2012-38359-C03-01 (including the FEDER financial support). Authors also thank the Basque Country Government for financial support (ACTIMAT project, ETORTEK Program, IE13-380, and Ayudas para Grupos de Investigación del Sistema Universitario Vasco Program, IT718-13)

Effect of spark plasma sintering and high-pressure torsion on the microstructural and mechanical properties of a Cu–SiC composite

This investigation examines the problem of homogenization in metal matrix composites (MMCs) and the methods of increasing their strength using severe plastic deformation (SPD). In this research MMCs of pure copper and silicon carbide were synthesized by spark plasma sintering (SPS) and then further processed via highpressure torsion (HPT). The microstructures in the sintered and in the deformed materials were investigated using Scanning Electron Microscopy (SEM) and Scanning Transmission Electron Microscopy (STEM). The mechanical properties were evaluated in microhardness tests and in tensile testing. The thermal conductivity of the composites was measured with the use of a laser pulse technique. Microstructural analysis revealed that HPT processing leads to an improved densification of the SPS-produced composites with significant grain refinement in the copper matrix and with fragmentation of the SiC particles and their homogeneous distribution in the copper matrix. The HPT processing of Cu and the Cu-SiC samples enhanced their mechanical properties at the expense of limiting their plasticity. Processing by HPT also had a major influence on the thermal conductivity of materials. It is demonstrated that the deformed samples exhibit higher thermal conductivity than the initial coarse-grained samples

Analysis of technical condition of steam turbine rotors based on miniature samples obtained semi-destructively

Precyzyjna ocena stopnia degradacji materiału wirnika turbiny parowej wymaga przeprowadzenia specjalistycznych badań materiałowych, uwzględniających mikroskopię świetlną i skaningową oraz badania wytrzymałościowe. Ponieważ pozyskiwanie próbek o standardowych rozmiarach osłabiłoby pod względem wytrzymałościowym konstrukcję wirnika, w artykule zaprezentowano metodykę pobierania próbek materiału w sposób mało inwazyjny w stosunku do badanego obiektu, pozostawiający powierzchnię wirnika bez karbów i znacznych pocienień. Zastosowanie odpowiednich parametrów cięcia, chłodzenia i mocowania urządzenia umożliwiło pobranie niewielkich próbek o niezmienionej, nieodkształconej i nieprzegrzanej mikrostrukturze. W pracy omówiono metodykę badań wytrzymałościowych pobranego w ten sposób materiału przy wykorzystaniu małych próbek tj. statycznej próby rozciągania oraz metody zginania miniaturowych dysków (Small Punch Test).Accurate evaluation of the turbine rotor material degradation requires specialized material testing, including light microscopy, SE M and tensile test. Since obtaining standard size samples would significantly weaken the rotor construction, the paper presents a methodology for semi-destructive sampling the material, leaving the surface of the rotor without notches and with a relatively small wall loss. The application of suitable cutting parameters, cooling and equipment fixing enabled the sampling of small samples without interfering in their microstructure. The paper discusses the methodology of mechanical testing of the obtained material with the use of miniaturized specimens such as Miniature Specimen Tensile Test (MSTT ) and Small Punch Test (SPT) method