Modification of polyethylene by RF plasma in different/mixture gases

Herein, low-density polyethylene (LDPE) films were treated using radio-frequency plasma discharge in the presence of air, nitrogen, oxygen, argon, and their mixtures to introduce new chemical functionalities. The surface properties of treated LDPE were qualitatively and quantitatively characterized using various analytical and microscopic techniques. It was found that the optimum plasma treatment for LDPE occurs in the presence of air plasma at an exposure time of 120 s and 80 W of nominal power. The plasma formed layer had tendency to increasing thickness with increasing treatment time up to 60 s using air and oxygen and even more with inert gases. An aging study of plasma-treated LDPE samples stored in ambient air or water medium revealed the partial hydrophobic recovery.Funding: This publication was made possible by an Award JSREP07-022-3-010 from the Qatar National Research Fund (a member of The Qatar Foundation).Scopu

Novel Slippery Liquid-Infused Porous Surfaces (SLIPS) based on electrospun polydimethylsiloxane/polystyrene fibrous structures infused with natural blackseed oil

Hydrophobic fibrous slippery liquid-infused porous surfaces (SLIPS) were fabricated by electrospinning polydimethylsiloxane (PDMS) and polystyrene (PS) as a carrier polymer on plasma-treated polyethylene (PE) and polyurethane (PU) substrates. Subsequent infusion of blackseed oil (BSO) into the porous structures was applied for the preparation of the SLIPS. SLIPS with infused lubricants can act as a repellency layer and play an important role in the prevention of biofilm formation. The effect of polymer solutions used in the electrospinning process was investigated to obtain well-defined hydrophobic fibrous structures. The surface properties were analyzed through various optical, macroscopic and spectroscopic techniques. A comprehensive investigation of the surface chemistry, surface morphology/topography, and mechanical properties was carried out on selected samples at optimized conditions. The electrospun fibers prepared using a mixture of PDMS/PS in the ratio of 1:1:10 (g/g/mL) using tetrahydrofuran (THF) solvent showed the best results in terms of fiber uniformity. The subsequent infusion of BSO into the fabricated PDMS/PS fiber mats exhibited slippery behavior regarding water droplets. Moreover, prepared SLIPS exhibited antibacterial activity against Staphylococcus aureus and Escherichia coli bacterium strains.RP/CPS/2022/001, RP/CPS/2022/002; Qatar National Research Fund, QNRFQatar National Research Fund (a member of The Qatar Foundation) [NPRP13S-0123-200153, JSREP 07-022-3-010]; Ministry of Education, Youth and Sports of the Czech Republic DKRVO [RP/CPS/2022/001, RP/CPS/2022/002

Slippery liquid-infused porous polymeric surfaces based on natural oil with antimicrobial effect

Many polymer materials have found a wide variety of applications in biomedical indus-tries due to their excellent mechanical properties. However, the infections associated with the bio-film formation represent serious problems resulting from the initial bacterial attachment on the polymeric surface. The development of novel slippery liquid-infused porous surfaces (SLIPSs) repre-sents promising method for the biofilm formation prevention. These surfaces are characterized by specific microstructural roughness able to hold lubricants inside. The lubricants create a slippery layer for the repellence of various liquids, such as water and blood. In this study, effective antimi-crobial modifications of polyethylene (PE) and polyurethane (PU), as commonly used medical pol-ymers, were investigated. For this purpose, low-temperature plasma treatment was used initially for activation of the polymeric surface, thereby enhancing surface and adhesion properties. Subse-quently, preparation of porous microstructures was achieved by electrospinning technique using polydimethylsiloxane (PDMS) in combination with polyamide (PA). Finally, natural black seed oil (BSO) infiltrated the produced fiber mats acting as a lubricating layer. The optimized fiber mats’ production was achieved using PDMS/PA mixture at ratio 1:1:20 (g/g/mL) using isopropyl alcohol as solvent. The surface properties of produced slippery surfaces were analyzed by various microscopic and optics techniques to obtain information about wettability, sliding behavior and surface morphology/topography. The modified PE and PU substrates demonstrated slippery behavior of an impinged water droplet at a small tilting angle. Moreover, the antimicrobial effects of the produced SLIPs using black seed oil were proven against Gram-positive Staphylococcus aureus (S. au-reus) and Gram-negative Escherichia coli (E. coli). © 2021 by the authors. Licensee MDPI, Basel, Switzerland.Qatar National Research Fund ( Qatar Foundation) [JSREP07-022-3-010]; Qatar University [QUCG-CAM-20/21-3]; Ministry of Education, Youth and Sports of the Czech Republic DKRVO [RP/CPS/2020/001]Qatar National Research Fund, QNRF; Ministerstvo Školství, Mládeže a Tělovýchovy, MŠMT: RP/CPS/2020/001; Qatar University, QU: QUCG-CAM-20/21-

Surface Functionalization of a Polyurethane Surface via Radio-Frequency Cold Plasma Treatment Using Different Gases

Herein, the surface treatment of polyurethane (PU) films via air, O2, N2, Ar, and their mixtures were tested. The treatment was performed to incorporate new polar functionalities on the polymer surface and achieve improved hydrophilic characteristics. The PU films were subjected to RF low-temperature plasma treatment. It was found that plasma treatment immensely enhanced the hydrophilic surface properties of the PU films in comparison with those of the pristine samples; the maximum plasma effect occurred for the PU sample in the presence of air plasma with treatment time of 180 s at nominal power of 80 W. The surface topography was also found to vary with plasma exposure time and the type of gas being used due to the reactivity of the gaseous media. Roughness analysis revealed that at higher treatment times, the etching/degradation of the surface became more pronounced. Surface chemistry studies revealed increased O2 and N2 elemental groups on the surface upon exposure to O2, N2, air, and Ar. Additionally, the aging study revealed that samples treated in the presence of air and Ar were more stable in comparison to those of the other gases for both the contact angle and peel test measurements

Oxygen-deficient perovskites for oxygen evolution reaction in alkaline media: a review

Oxygen vacancies in complex metal oxides and specifically in perovskites are demonstrated to significantly enhance their electrocatalytic activities due to facilitating a degree of control in the material’s intrinsic properties. The reported enhancement in intrinsic OER activity of oxygen-deficient perovskites surfaces has inspired their fabrication via a myriad of schemes. Oxygen vacancies in perovskites are amongst the most favorable anionic or Schottky defects to be induced due to their low formation energies. This review discusses recent efforts for inducing oxygen vacancies in a multitude of perovskites, including facile and environmentally benign synthesis strategies, characterization techniques, and detailed insight into the intrinsic mechanistic modulation of perovskite electrocatalysts. Experimental, analytical, and computational techniques dedicated to the understanding of the improvement of OER activities upon oxygen vacancy induction are summarized in this work. The identification and utilization of intrinsic activity descriptors for the modulation of configurational structure, improvement in bulk charge transport, and favorable inflection of the electronic structure are also discussed. It is our foresight that the approaches, challenges, and prospects discussed herein will aid researchers in rationally designing highly active and stable perovskites that can outperform noble metal-based OER electrocatalysts.Other Information Published in: Emergent Materials License: https://creativecommons.org/licenses/by/4.0See article on publisher's website: http://dx.doi.org/10.1007/s42247-020-00123-z</p

Slippery Liquid-Infused Porous Polymeric Surfaces Based on Natural Oil with Antimicrobial Effect

Many polymer materials have found a wide variety of applications in biomedical industries due to their excellent mechanical properties. However, the infections associated with the biofilm formation represent serious problems resulting from the initial bacterial attachment on the polymeric surface. The development of novel slippery liquid-infused porous surfaces (SLIPSs) represents promising method for the biofilm formation prevention. These surfaces are characterized by specific microstructural roughness able to hold lubricants inside. The lubricants create a slippery layer for the repellence of various liquids, such as water and blood. In this study, effective antimicrobial modifications of polyethylene (PE) and polyurethane (PU), as commonly used medical polymers, were investigated. For this purpose, low-temperature plasma treatment was used initially for activation of the polymeric surface, thereby enhancing surface and adhesion properties. Subsequently, preparation of porous microstructures was achieved by electrospinning technique using polydimethylsiloxane (PDMS) in combination with polyamide (PA). Finally, natural black seed oil (BSO) infiltrated the produced fiber mats acting as a lubricating layer. The optimized fiber mats&rsquo; production was achieved using PDMS/PA mixture at ratio 1:1:20 (g/g/mL) using isopropyl alcohol as solvent. The surface properties of produced slippery surfaces were analyzed by various microscopic and optics techniques to obtain information about wettability, sliding behavior and surface morphology/topography. The modified PE and PU substrates demonstrated slippery behavior of an impinged water droplet at a small tilting angle. Moreover, the antimicrobial effects of the produced SLIPs using black seed oil were proven against Gram-positive Staphylococcus aureus (S. aureus) and Gram-negative Escherichia coli (E. coli)

Thermodynamic investigation of hydrogen enrichment and carbon suppression using chemical additives in ethanol dry reforming

In this study, a thermodynamic equilibrium analysis has been performed on ethanol dry reforming in presence of commonly used reducing agents such as glycine, hydrazine, urea and ammonia. The effect of these agents on hydrogen enrichment and carbon suppression has been investigated at one atmospheric pressure and 300 K 1200 K temperature. Among the investigated additives, hydrazine was found to be the most suitable for maximizing hydrogen production and removing elemental carbon formation. This study was further extended to ethanol steam reforming and similar conclusions were obtained. Industrial significance of this study is associated with reforming reactions where catalyst deactivation due to coking is a major problem. Based on the results obtained, addition of suitable chemical additives in the feed could alleviate this problem to a significant level and help in improving catalyst life cycle. 2016 Hydrogen Energy Publications LLCThis publication was made possible by UREP grant ( UREP17-047-2-015 ) from the Qatar National Research Fund (a member of Qatar foundation). The statements made herein are solely the responsibility of the author(s).Scopu