63 research outputs found

    Testability enhancement of a basic set of CMOS cells

    Get PDF
    Testing should be evaluated as the ability of the test patterns to cover realistic faults, and high quality IC products demand high quality testing. We use a test strategy based on physical design for testability (to discover both open and short faults, which are difficult or even impossible to detect). Consequentially, layout level design for testability (LLDFT) rules have been developed, which prevent the faults, or at least reduce the chance of their appearing. The main purpose of this work is to apply a practical set of LLDFT rules to the library cells designed by the Centre Nacional de Microelectrònica (CNM) and obtain a highly testable cell library. The main results of the application of the LLDFT rules (area overheads and performance degradation) are summarized and the results are significant since IC design is highly repetitive; a small effort to improve cell layout can bring about great improvement in design

    Layout level design for testability strategy applied to a CMOS cell library

    Get PDF
    The layout level design for testability (LLDFT) rules used here allow to avoid some hard to detect faults or even undetectable faults on a cell library by modifying the cell layout without changing their behavior and achieving a good level of reliability. These rules avoid some open faults or reduce their appearance probability. The main purpose has been to apply that set of LLDFT rules on the cells of the library designed at the Centre Nacional de Microelectronica (CNM) in order to obtain a highly testable cell library. The authors summarize the main results (area overhead and performance degradation) of the application of the LLDFT rules on the cell

    IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling ADC

    Get PDF
    This work presents IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling analog-to-digital converter using a built-in current sensor [BICS]. Gate-drain, source-drain, gate-source and gate-substrate bridging faults are injected using fault injection transistors. All the four faults cause varying fault currents and are successfully detected by the BICS at a good operation speed. The BICS have a negligible impact on the performance of the modulator and an external pin is provided to completely cut-off the BICS from the modulator. The modulator was designed and fabricated in 1.5 μm n-well CMOS process. The decimator was designed on Altera\u27s FLEXE20K board using Verilog. The modulator and decimator were assembled together to form a sigma-delta ADC

    Iddq testing of a CMOS 10-bit charge scaling digital-to-analog converter

    Get PDF
    This work presents an effective built-in current sensor (BICS), which has a very small impact on the performance of the circuit under test (CUT). The proposed BICS works in two-modes the normal mode and the test mode. In the normal mode the BICS is isolated from the CUT due to which there is no performance degradation of the CUT. In the testing mode, our BICS detects the abnormal current caused by permanent manufacturing defects. Further more our BICS can also distinguish the type of defect induced (Gate-source short, source-drain short and drain-gate short). Our BICS requires neither an external voltage source nor current source. Hence the BICS requires less area and is more efficient than the conventional current sensors. The circuit under test is a 10-bit digital to analog converter using charge-scaling architecture

    [Delta] IDDQ testing of a CMOS 12-bit charge scaling digital-to-analog converter

    Get PDF
    This work presents design, implementation and test of a built-in current sensor (BICS) for ∆IDDQ testing of a CMOS 12-bit charge scaling digital-to-analog converter (DAC). The sensor uses power discharge method for the fault detection. The sensor operates in two modes, the test mode and the normal mode. In the test mode, the BICS is connected to the circuit under test (CUT) which is DAC and detects abnormal currents caused by manufacturing defects. In the normal mode, BICS is isolated from the CUT. The BICS is integrated with the DAC and is implemented in a 0.5 μm n-well CMOS technology. The DAC uses charge scaling method for the design and a low voltage (0 to 2.5 V) folded cascode op-amp. The built-in current sensor (BICS) has a resolution of 0.5 μA. Faults have been introduced into DAC using fault injection transistors (FITs). The method of ∆IDDQ testing has been verified both from simulation and experimental measurements

    Binning for IC Quality: Experimental Studies on the SEMATECH Data

    Get PDF
    The earlier smaller bipolar study did not provide a high enough bin 0 population to directly observe test escapes and thereby estimate defect levels for the best bin. Results presented here indicate that the best bin can be reasonably expected to show a 2 - 5 factor improvement in defect levels over the average for the lot for moderate to high yields (the overall yield for these experiments was approximately 65%). The experiments also confirm the dependence of the best bin quality on test transparency. The defect level improvement is poorer for the case Of IDDQ escapes where the tests applied had a much higher escape rate. Overall experimental results are consistent with analytical projections for typical values of the clustering parameter in [9]. The final version of this paper will include extensive analysis to validate the analytical models based on this data
    • …
    corecore