Design for testability of a latch-based design

Abstract. The purpose of this thesis was to decrease the area of digital logic in a power management integrated circuit (PMIC), by replacing selected flip-flops with latches. The thesis consists of a theory part, that provides background theory for the thesis, and a practical part, that presents a latch register design and design for testability (DFT) method for achieving an acceptable level of manufacturing fault coverage for it. The total area was decreased by replacing flip-flops of read-write and one-time programmable registers with latches. One set of negative level active primary latches were shared with all the positive level active latch registers in the same register bank. Clock gating was used to select which latch register the write data was loaded to from the primary latches. The latches were made transparent during the shift operation of partial scan testing. The observability of the latch register clock gating logic was improved by leaving the first bit of each latch register as a flip-flop. The controllability was improved by inserting control points. The latch register design, developed in this thesis, resulted in a total area decrease of 5% and a register bank area decrease of 15% compared to a flip-flop-based reference design. The latch register design manages to maintain the same stuck-at fault coverage as the reference design.Salpaperäisen piirin testattavuuden suunnittelu. Tiivistelmä. Tämän opinnäytetyön tarkoituksena oli pienentää digitaalisen logiikan pinta-alaa integroidussa tehonhallintapiirissä, korvaamalla valitut kiikut salpapiireillä. Opinnäytetyö koostuu teoriaosasta, joka antaa taustatietoa opinnäytetyölle, ja käytännön osuudesta, jossa esitellään salparekisteripiiri ja testattavuussuunnittelun menetelmä, jolla saavutettiin riittävän hyvä virhekattavuus salparekisteripiirille. Kokonaispinta-alaa pienennettiin korvaamalla luku-kirjoitusrekistereiden ja kerran ohjelmoitavien rekistereiden kiikut salpapiireillä. Yhdet negatiivisella tasolla aktiiviset isäntä-salpapiirit jaettiin kaikkien samassa rekisteripankissa olevien positiivisella tasolla aktiivisten salparekistereiden kanssa. Kellon portittamisella valittiin mihin salparekisteriin kirjoitusdata ladattiin yhteisistä isäntä-salpapireistä. Osittaisessa testipolkuihin perustuvassa testauksessa salpapiirit tehtiin läpinäkyviksi siirtooperaation aikana. Salparekisterin kellon portituslogiikan havaittavuutta parannettiin jättämällä jokaisen salparekisterin ensimmäinen bitti kiikuksi. Ohjattavuutta parannettiin lisäämällä ohjauspisteitä. Salparekisteripiiri, joka suunniteltiin tässä diplomityössä, pienensi kokonaispinta-alaa 5 % ja rekisteripankin pinta-alaa 15 % verrattuna kiikkuperäiseen vertailupiiriin. Salparekisteripiiri onnistuu pitämään saman juuttumisvikamallin virhekattavuuden kuin vertailupiiri

Identifying worst case test vectors for FPGA exposed to total ionization dose using design for testability techniques

Electronic devices often operate in harsh environments which contain a variation of radiation sources. Radiation may cause different kinds of damage to proper operation of the devices. Their sources can be found in terrestrial environments, or in extra-terrestrial environments like in space, or in man-made radiation sources like nuclear reactors, biomedical devices and high energy particles physics experiments equipment. Depending on the operation environment of the device, the radiation resultant effect manifests in several forms like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). TID effect causes an increase in the delay and the leakage current of CMOS circuits which may damage the proper operation of the integrated circuit. To ensure proper operation of these devices under radiation, thorough testing must be made especially in critical applications like space and military applications. Although the standard which describes the procedure for testing electronic devices under radiation emphasizes the use of worst case test vectors (WCTVs), they are never used in radiation testing due to the difficulty of generating these vectors for circuits under test. For decades, design for testability (DFT) has been the best choice for test engineers to test digital circuits in industry. It has become a very mature technology that can be relied on. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Surprisingly, however, radiation testing has not yet made use of this reliable technology. In this thesis, a novel methodology is proposed to extend the usage of DFT to generate WCTVs for delay failure in Flash based field programmable gate arrays (FPGAs) exposed to total ionizing dose (TID). The methodology is validated using MicroSemi ProASIC3 FPGA and cobalt 60 facility

Transition Faults and Transition Path Delay Faults: Test Generation, Path Selection, and Built-In Generation of Functional Broadside Tests

As the clock frequency and complexity of digital integrated circuits increase rapidly, delay testing is indispensable to guarantee the correct timing behavior of the circuits. In this dissertation, we describe methods developed for three aspects of delay testing in scan-based circuits: test generation, path selection and built-in test generation. We first describe a deterministic broadside test generation procedure for a path delay fault model named the transition path delay fault model, which captures both large and small delay defects. Under this fault model, a path delay fault is detected only if all the individual transition faults along the path are detected by the same test. To reduce the complexity of test generation, sub-procedures with low complexity are applied before a complete branch-and-bound procedure. Next, we describe a method based on static timing analysis to select critical paths for test generation. Logic conditions that are necessary for detecting a path delay fault are considered to refine the accuracy of static timing analysis, using input necessary assignments. Input necessary assignments are input values that must be assigned to detect a fault. The method calculates more accurate path delays, selects paths that are critical during test application, and identifies undetectable path delay faults. These two methods are applicable to off-line test generation. For large circuits with high complexity and frequency, built-in test generation is a cost-effective method for delay testing. For a circuit that is embedded in a larger design, we developed a method for built-in generation of functional broadside tests to avoid excessive power dissipation during test application and the overtesting of delay faults, taking the functional constraints on the primary input sequences of the circuit into consideration. Functional broadside tests are scan-based two-pattern tests for delay faults that create functional operation conditions during test application. To avoid the potential fault coverage loss due to the exclusive use of functional broadside tests, we also developed an optional DFT method based on state holding to improve fault coverage. High delay fault coverage can be achieved by the developed method for benchmark circuits using simple hardware

A testability metric for path delay faults and its application

Abstract — In this paper, we propose a new testability metric for path delay faults. The metric is computed efficiently using a non-enumerative algorithm. It has been validated through extensive experiments and the results indicate a strong correlation between the proposed metric and the path delay fault testability of the circuit. We further apply this metric to derive a path delay fault test application scheme for scan-based BIST. The selection of the test scheme is guided by the proposed metric. The experimental results illustrate that the derived test application scheme can achieve a higher path delay fault coverage in scan-based BIST. Because of the effectiveness and efficient computation of this metric, it can be used to derive other design-for-testability techniques for path delay faults. I

A Flexible Scan-in Power Control Method in Logic BIST and Its Evaluation with TEG Chips

High power dissipation in scan-based logic built-in self-test (LBIST) is a crucial issue that can cause over-testing, reliability degradation, chip damage, and so on. While many sophisticated approaches to low-power testing have been proposed in the past, it remains a serious problem to control the test power of LBIST to a predetermined appropriate level that matches the power requirements of the circuit-under-test. This paper proposes a novel power-control method for LBIST that can control the scan-shift power to an arbitrary level. The proposed method modifies pseudo-random patterns generated by an embedded test pattern generator (TPG) so that the modified patterns have the specific toggle rate without sacrificing fault coverage and test time. In order to evaluate the effectiveness of the proposed method, this paper shows not only simulation-based experimental results but also measurement results on test element group (TEG) chips

Infrastructures and Algorithms for Testable and Dependable Systems-on-a-Chip

Every new node of semiconductor technologies provides further miniaturization and higher performances, increasing the number of advanced functions that electronic products can offer. Silicon area is now so cheap that industries can integrate in a single chip usually referred to as System-on-Chip (SoC), all the components and functions that historically were placed on a hardware board. Although adding such advanced functionality can benefit users, the manufacturing process is becoming finer and denser, making chips more susceptible to defects. Today’s very deep-submicron semiconductor technologies (0.13 micron and below) have reached susceptibility levels that put conventional semiconductor manufacturing at an impasse. Being able to rapidly develop, manufacture, test, diagnose and verify such complex new chips and products is crucial for the continued success of our economy at-large. This trend is expected to continue at least for the next ten years making possible the design and production of 100 million transistor chips. To speed up the research, the National Technology Roadmap for Semiconductors identified in 1997 a number of major hurdles to be overcome. Some of these hurdles are related to test and dependability. Test is one of the most critical tasks in the semiconductor production process where Integrated Circuits (ICs) are tested several times starting from the wafer probing to the end of production test. Test is not only necessary to assure fault free devices but it also plays a key role in analyzing defects in the manufacturing process. This last point has high relevance since increasing time-to-market pressure on semiconductor fabrication often forces foundries to start volume production on a given semiconductor technology node before reaching the defect densities, and hence yield levels, traditionally obtained at that stage. The feedback derived from test is the only way to analyze and isolate many of the defects in today’s processes and to increase process’s yield. With the increasing need of high quality electronic products, at each new physical assembly level, such as board and system assembly, test is used for debugging, diagnosing and repairing the sub-assemblies in their new environment. Similarly, the increasing reliability, availability and serviceability requirements, lead the users of high-end products performing periodic tests in the field throughout the full life cycle. To allow advancements in each one of the above scaling trends, fundamental changes are expected to emerge in different Integrated Circuits (ICs) realization disciplines such as IC design, packaging and silicon process. These changes have a direct impact on test methods, tools and equipment. Conventional test equipment and methodologies will be inadequate to assure high quality levels. On chip specialized block dedicated to test, usually referred to as Infrastructure IP (Intellectual Property), need to be developed and included in the new complex designs to assure that new chips will be adequately tested, diagnosed, measured, debugged and even sometimes repaired. In this thesis, some of the scaling trends in designing new complex SoCs will be analyzed one at a time, observing their implications on test and identifying the key hurdles/challenges to be addressed. The goal of the remaining of the thesis is the presentation of possible solutions. It is not sufficient to address just one of the challenges; all must be met at the same time to fulfill the market requirements

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

A novel high-speed trellis-coded modulation encoder/decoder ASIC design

Trellis-coded Modulation (TCM) is used in bandlimited communication systems. TCM efficiency improves coding gain by combining modulation and forward error correction coding in one process. In TCM, the bandwidth expansion is not required because it uses the same symbol rate and power spectrum; the differences are the introduction of a redundancy bit and the use of a constellation with double points. In this thesis, a novel TCM encoder/decoder ASIC chip implementation is presented. This ASIC codec not only increases decoding speed but also reduces hardware complexity. The algorithm and technique are presented for a 16-state convolutional code which is used in standard 256-QAM wireless systems. In the decoder, a Hamming distance is used as a cost function to determine output in the maximum likelihood Viterbi decoder. Using the relationship between the delay states and the path state in the Trellis tree of the code, a pre-calculated Hamming distances are stored in a look-up table. In addition, an output look-up-table is generated to determine the decoder output. This table is established by the two relative delay states in the code. The thesis provides details of the algorithm and the structure of TCM codec chip. Besides using parallel processing, the ASIC implementation also uses pipelining to further increase decoding speed. The codec was implemented in ASIC using standard 0.18ƒÝm CMOS technology; the ASIC core occupied a silicon area of 1.1mm2. All register transfer level code of the codec was simulated and synthesized. The chip layout was generated and the final chip was fabricated by Taiwan Semiconductor Manufacturing Company through the Canadian Microelectronics Corporation. The functional testing of the fabricated codec was performed partially successful; the timing testing has not been fully accomplished because the chip was not always stable