Hot-Carrier Degradation in Power LDMOS: Selective LOCOS-Versus STI-Based Architecture

In this paper, we present an analysis of the degradation induced by hot-carrier stress in new generation power lateral double-diffused MOS (LDMOS) transistors. Two architectures with the same nominal voltage and comparable performance featuring a selective LOCOS and a shallow-trench isolation are investigated by means of constant voltage stress measurements and TCAD simulations. In particular, the on-resistance degradation in linear regime is experimentally extracted and numerically reproduced under different stress conditions. A similar amount of degradation has been reached by the two architectures, although different physical mechanisms contribute to the creation of the interface states. By using a recently developed physics-based degradation model, it has been possible to distinguish the damage due to collisions of single high-energetic electrons (single-particle events) and the contribution of colder electrons impinging on the silicon/oxide interface (multiple-particle events). A clear dominance of the single-electron collisions has been found in the case of LOCOS structure, whereas the multiple-particle effect plays a clear role in STI-based device at larger gate-voltage stress

Full Understanding of Hot Electrons and Hot/Cold Holes in the Degradation of p-channel Power LDMOS Transistors

Degradation induced by hot-carrier stress is a crucial issue for the reliability of power LDMOS transistors. This is even more true for the p-channel LDMOS in which, unlike the n-channel counterpart, both the majority and minority carriers play a fundamental role on the device reliability. An in-depth study of the microscopic mechanisms induced by hot-carrier stress in new generation BCD integrated p-channel LDMOS is presented in this paper. The effect of the competing electron and hole trapping mechanisms on the on-resistance drift has been thoroughly analyzed. To this purpose, TCAD simulations including the deterministic solution of Boltzmann transport equation and the microscopic degradation mechanisms have been used, to the best of our knowledge, for the first time. The insight gained into the degradation sources and dynamics will provide a relevant basis for future device optimization

Chip- and System-Level Reliability on SiC-based Power Modules

The blocking voltage, switching frequency and temperature tolerance of power devices have been greatly improved due to the revolution of wide bandgap (WBG) materials, such as silicon carbide (SiC) and gallium nitride (GaN). Owing to the development of SiC-based power devices, the power rating, operating voltage, and power density of power modules have been significantly improved. However, the reliability of SiC-based power modules has not been fully explored yet. Thus, this dissertation focuses on the chip- and system-level reliability on SiC-based power modules. For chip-level reliability, this work focuses on on-chip SiC ESD protection devices for SiC-based integrated circuits (ICs). In order to develop SiC ESD protection devices, SiC-based Ohmic contact and ion implantation have been studied. Nickel/Titanium/Aluminum (Ni/Ti/Al) metal stacks were deposited on SiC substrates to form Ohmic contact. Circular transfer length method (CTLM) structures were fabricated to characterize contact resistivity. Ion implantation was designed and simulated by Sentraurus technology computer aided design (TCAD) software. Secondary-ion mass spectrometry (SIMS) results show a good match with the simulation results. In addition, SiC ESD protection devices, such as N-type metal-oxide-semiconductor (NMOS), laterally diffused metal-oxide-semiconductor (LDMOS), high-voltage silicon controlled rectifier (HV-SCR) and low-voltage silicon controlled rectifier (LV-SCR), have been designed. Transmission line pulse (TLP) and very fast TLP (VF-TLP) measurements were carried out to characterize their ESD performance. The proposed SiC-based HV-SCR shows the highest failure current on TLP measurement and can be used as an area-efficient ESD protection device. On the other hand, for system-level reliability, this dissertation focuses on the galvanic isolation of high-temperature SiC power modules. Low temperature co-fired ceramics (LTCC) based high-temperature optocouplers were designed and fabricated as galvanic isolators. The LTCC-based high-temperature optocouplers show promising driving capability and steady response speed from 25 ºC to 250 ºC. In order to verify the performance of the high-temperature optocouplers at the system level, LTCC-based gate drivers that utilize the high-temperature optocouplers as galvanic isolators were designed and integrated into a high-temperature SiC-based power module. Finally, the high-temperature power module with integrated LTCC-based gate drivers was characterized by DPTs from 25 ºC to 200 ºC. The power module shows reliable switching performance at elevated temperatures

Chip- and System-Level Reliability on SiC-based Power Modules

The blocking voltage, switching frequency and temperature tolerance of power devices have been greatly improved due to the revolution of wide bandgap (WBG) materials, such as silicon carbide (SiC) and gallium nitride (GaN). Owing to the development of SiC-based power devices, the power rating, operating voltage, and power density of power modules have been significantly improved. However, the reliability of SiC-based power modules has not been fully explored yet. Thus, this dissertation focuses on the chip- and system-level reliability on SiC-based power modules. For chip-level reliability, this work focuses on on-chip SiC ESD protection devices for SiC-based integrated circuits (ICs). In order to develop SiC ESD protection devices, SiC-based Ohmic contact and ion implantation have been studied. Nickel/Titanium/Aluminum (Ni/Ti/Al) metal stacks were deposited on SiC substrates to form Ohmic contact. Circular transfer length method (CTLM) structures were fabricated to characterize contact resistivity. Ion implantation was designed and simulated by Sentraurus technology computer aided design (TCAD) software. Secondary-ion mass spectrometry (SIMS) results show a good match with the simulation results. In addition, SiC ESD protection devices, such as N-type metal-oxide-semiconductor (NMOS), laterally diffused metal-oxide-semiconductor (LDMOS), high-voltage silicon controlled rectifier (HV-SCR) and low-voltage silicon controlled rectifier (LV-SCR), have been designed. Transmission line pulse (TLP) and very fast TLP (VF-TLP) measurements were carried out to characterize their ESD performance. The proposed SiC-based HV-SCR shows the highest failure current on TLP measurement and can be used as an area-efficient ESD protection device. On the other hand, for system-level reliability, this dissertation focuses on the galvanic isolation of high-temperature SiC power modules. Low temperature co-fired ceramics (LTCC) based high-temperature optocouplers were designed and fabricated as galvanic isolators. The LTCC-based high-temperature optocouplers show promising driving capability and steady response speed from 25 ºC to 250 ºC. In order to verify the performance of the high-temperature optocouplers at the system level, LTCC-based gate drivers that utilize the high-temperature optocouplers as galvanic isolators were designed and integrated into a high-temperature SiC-based power module. Finally, the high-temperature power module with integrated LTCC-based gate drivers was characterized by DPTs from 25 ºC to 200 ºC. The power module shows reliable switching performance at elevated temperatures

Electrical characterization and modelling of lateral DMOS transistor:investigation of capacitances and hot-carrier impact

With the work reported in this manuscript we have essentially contributed to the electrical characterization and modelling of high voltage MOSFETs, more particularly DMOS architectures such as X-DMOS and L-DMOS able to sustain voltages ranging from 30V to 100V. The technology information and the investigated devices have been kindly provided by AMIS, Belgium (former Alcatel Microelectronics). In general, all the initial defined targets in term of the orientation of our work, as defined in the introduction chapter, have been maintained along the progress of the work. However, sometimes, based on the obtained results we have decided to pay more attention to some less explored topics such as the hot carrier impact of DMOS capacitances and the combined effect of stress and temperature, which initially were not among the planned activities. However, we believe that we have contributed to some of the planned targets. We experimentally validated the concept of intrinsic drain voltage; a modeling concept dedicated to the modeling of HV MOSFET and demonstrated its usefulness for the DC and AC modelling of HV devices. We proposed an original mathematical yet quasi-empirical formulation for the bias-dependent drift series resistance of DMOS transistor, which is very accurate for modelling all the regimes of operation of the high voltage device. We combined for the first time such a model with EKV low voltage MOSFET model developed at EPFL. We also have reported on models for the capacitances of high voltage devices at two levels: equivalent circuits for small signal operation based on VK-concept and large signal charge-based models. These models capture the main physical charge distribution in the device but they are less adapted for fast circuit simulation. In the field of device reliability, we have originally contributed to the investigation of hot carrier effects on DC and AC characteristics of DMOS transistors, with key emphasis on the degradation of transistor capacitances and the influence of the temperature. At our knowledge, our work reported in this chapter is among the first reports existing in this field. We have essentially shown that the monitoring of capacitance degradation if mandatory for a deep understanding of the degradation mechanisms and, in conjunction with DC parameter degradation, could offer correct insights for reliability issues. Even more, we have shown situations (by comparing two fundamental types of stresses) when the capacitance degradation method by HC is much more sensitive than DC parameter degradation method. Of course, some of the combined stress-temperature investigations were too complex to find very coherent explications for all the observed effects but our work stress out the interest and significance of such an approach for defining the SOA of high voltage devices, in general. Overall, our work can be considered as placed at the interface between electrical characterization and modelling of high voltage devices emerging from conventional low voltage CMOS technology, continuing the research tradition in the field established at the Electronics laboratory (LEG) of EPF Lausanne

Transient Safe Operating Area (tsoa) For Esd Applications

A methodology to obtain design guidelines for gate oxide input pin protection and high voltage output pin protection in Electrostatic Discharge (ESD) time frame is developed through measurements and Technology Computer Aided Design (TCAD). A set of parameters based on transient measurements are used to define Transient Safe Operating Area (TSOA). The parameters are then used to assess effectiveness of protection devices for output and input pins. The methodology for input pins includes establishing ESD design targets under Charged Device Model (CDM) type stress in low voltage MOS inputs. The methodology for output pins includes defining ESD design targets under Human Metal Model (HMM) type stress in high voltage Laterally Diffused MOS (LDMOS) outputs. First, the assessment of standalone LDMOS robustness is performed, followed by establishment of protection design guidelines. Secondly, standalone clamp HMM robustness is evaluated and a prediction methodology for HMM type stress is developed based on standardized testing. Finally, LDMOS and protection clamp parallel protection conditions are identifie

Comparative study of RESURF Si/SiC LDMOSFETs for high-temperature applications using TCAD modeling

This paper analyses the effect of employing an Si on semi-insulating SiC (Si/SiC) device architecture for the implementation of 600-V LDMOSFETs using junction isolation and dielectric isolation reduced surface electric field technologies for high-temperature operations up to 300 °C. Simulations are carried out for two Si/SiC transistors designed with either PN or silicon-on-insulator (SOI) and their equivalent structures employing bulk-Si or SOI substrates. Through comparisons, it is shown that the Si/SiC devices have the potential to operate with an offstate leakage current as low as the SOI device. However, the low-side resistance of the SOI LDMOSFET is smaller in value and less sensitive to temperature, outperforming both Si/SiC devices. Conversely, under high-side configurations, the Si/SiC transistors have resistances lower than that of the SOI at high substrate bias, and invariable with substrate potential up to −200 V, which behaves similar to the bulkSi LDMOS at 300 K. Furthermore, the thermal advantage of the Si/SiC over other structures is demonstrated by using a rectangle power pulse setup in Technology Computer-Aided design simulations

Lateral Power Mosfets Hardened Against Single Event Radiation Effects

The underlying physical mechanisms of destructive single event effects (SEE) from heavy ion radiation have been widely studied in traditional vertical double-diffused power MOSFETs (VDMOS). Recently lateral double-diffused power MOSFETs (LDMOS), which inherently provide lower gate charge than VDMOS, have become an attractive option for MHz-frequency DC-DC converters in terrestrial power electronics applications [1]. There are growing interests in extending the LDMOS concept into radiation-hard space applications. Since the LDMOS has a device structure considerably different from VDMOS, the well studied single event burn-out (SEB) or single event gate rapture (SEGR) response of VDMOS cannot be simply assumed for LDMOS devices without further investigation. A few recent studies have begun to investigate ionizing radiation effects in LDMOS devices, however, these studies were mainly focused on displacement damage and total ionizing dose (TID) effects, with very limited data reported on the heavy ion SEE response of these devices [2]-[5]. Furthermore, the breakdown voltage of the LDMOS devices in these studies was limited to less than 80 volts (mostly in the range of 20-30 volts), considerably below the voltage requirement for some space power applications. In this work, we numerically and experimentally investigate the physical insights of SEE in two different fabricated LDMOS devices designed by the author and intended for use in radiation hard applications. The first device is a 24 V Resurf LDMOS fabricated on P-type epitaxial silicon on a P+ silicon substrate. The second device is a iv much different 150 V SOI Resurf LDMOS fabricated on a 1.0 micron thick N-type silicon-on-insulator substrate with a 1.0 micron thick buried silicon dioxide layer on an N-type silicon handle wafer. Each device contains internal features, layout techniques, and process methods designed to improve single event and total ionizing dose radiation hardness. Technology computer aided design (TCAD) software was used to develop the transistor design and fabrication process of each device and also to simulate the device response to heavy ion radiation. Using these simulations in conjunction with experimentally gathered heavy ion radiation test data, we explain and illustrate the fundamental physical mechanisms by which destructive single event effects occur in these LDMOS devices. We also explore the design tradeoffs for making an LDMOS device resistant to destructive single event effects, both in terms of electrical performance and impact on other radiation hardness metric

Optimisation of lateral super-junction multi-gate MOSFET for high drive current and low specific on-resistance in sub-100 V applications

The design and optimisation of a non-planar super-junction (SJ) Si MOSFET based on SOI technology for low voltage rating applications (below 100 V) is carried out with physically based commercial 3-D TCAD device simulations using Silvaco. We calibrate drift-diffusion simulations to experimental characteristics of the SJ multi-gate MOSFET (SJ-MGFET) aiming at improving drive current, breakdown voltage (BV), and specific on-resistance (Ron,sp). We investigate variations in the device architecture and improve device performance by optimizing doping profile under charge imbalance. The SJ-MGFET, using a folded alternating U-shaped n/p– SJ drift region pillar width of 0.3 μm with a trench depth of 2.7 μm achieves specific on-resistance (Ron,sp) of 0.21 mΩ.cm2 at a BV of 65 V. In comparison with conventional planar gate SJ-LDMOSFETs, the optimised SJ-MGFET gives 68% reduction in Ron,sp and 41% increase in a saturation drain current at a drain voltage of 5 V and a gate voltage of 10 V