Sub-band equalization filter design for improving dynamic range performance of modulated wideband converter

In this work, we propose an iterative method to improve the dynamic range performance of the Modulated Wideband Converter (MWC), which is multi-channel sampling system for digitizing wideband sparse signals below the Nyquist limit without loss of information by using compressive sensing techniques. Our method jointly designs FIR filters for each subband to equalize the frequency response characteristics of the all sub-bands of the MWC. Obtained results from the extensive computer simulations of the MWC system show that the proposed method improves the dynamic range performance of the MWC system significantly. © EURASIP 2017

A 2.4 Ghz Mimo Wireless Transceiver Design [TK5103.2. Q1 2008 f rb].

Kombinasi antara MIMO dan modulasi kesukuan dianggap sebagai salah satu penyelesaian yang paling berkesan bagi memperbaiki kecekapan spektrum dan meningkatkan kadar data untuk sistem komonikasi tanpa wayar bagi generasi akan datang . The combination of multiple input multiple output (MIMO) and quadrature modulation is regarded as one of the most promising solutions for improving spectrum efficiency and enhancing data rate for next-generation wireless communication systems

Communications techniques and equipment: A compilation

This Compilation is devoted to equipment and techniques in the field of communications. It contains three sections. One section is on telemetry, including articles on radar and antennas. The second section describes techniques and equipment for coding and handling data. The third and final section includes descriptions of amplifiers, receivers, and other communications subsystems

Design of a microwave imaging system for rapid wideband imaging

An imaging system composed of two linear arrays of antennas is designed through full-wave simulation and fabricated for use in synthetic aperture radar imaging. The arrays electronically scan along their antenna elements and are mechanically moved along a second orthogonal direction for scanning large two-dimensional areas quickly. Each linear array is printed on a circuit board where the antenna elements are integrated into the edge of the board as tapered slot-line antennas operating at 22 to 27 GHz. A multiplexer circuit is printed onto each linear array to transmit wideband signals to each antenna in the array. Receivers are printed onto the radiating end of the antennas on the edge of the circuit board. These receivers are less complex than traditional microwave receivers, and they require no phase calibration for synthetic aperture radar processing. A controller board is designed and fabricated to facilitate electronic scanning along the arrays and route measurement data to a PC for storage. The linear arrays and controller board are mounted on a small mechanical scanning table for moving the arrays along one direction. All receivers are calibrated for variations in voltage outputs among the elements by scanning a known target and applying an equalization matrix. Several targets are scanned by the final imaging system, and the resulting images show the ability of the system to detect dielectric contrast under the surface of dielectric materials. The tapered slot-line antenna is redesigned and improved for -10 dB reflection coefficient across the operating frequency band and higher voltage output of the receivers with respect to the original antenna design. Imaging results of the redesigned antenna show how refabricating the imaging system with the improved antenna will improve overall image quality of the system--Abstract, page iii

ワイヤレス通信のための先進的な信号処理技術を用いた非線形補償法の研究

The inherit nonlinearity in analogue front-ends of transmitters and receivers have had primary impact on the overall performance of the wireless communication systems, as it gives arise of substantial distortion when transmitting and processing signals with such circuits. Therefore, the nonlinear compensation (linearization) techniques become essential to suppress the distortion to an acceptable extent in order to ensure sufficient low bit error rate. Furthermore, the increasing demands on higher data rate and ubiquitous interoperability between various multi-coverage protocols are two of the most important features of the contemporary communication system. The former demand pushes the communication system to use wider bandwidth and the latter one brings up severe coexistence problems. Having fully considered the problems raised above, the work in this Ph.D. thesis carries out extensive researches on the nonlinear compensations utilizing advanced digital signal processing techniques. The motivation behind this is to push more processing tasks to the digital domain, as it can potentially cut down the bill of materials (BOM) costs paid for the off-chip devices and reduce practical implementation difficulties. The work here is carried out using three approaches: numerical analysis & computer simulations; experimental tests using commercial instruments; actual implementation with FPGA. The primary contributions for this thesis are summarized as the following three points: 1) An adaptive digital predistortion (DPD) with fast convergence rate and low complexity for multi-carrier GSM system is presented. Albeit a legacy system, the GSM, however, has a very strict requirement on the out-of-band emission, thus it represents a much more difficult hurdle for DPD application. It is successfully implemented in an FPGA without using any other auxiliary processor. A simplified multiplier-free NLMS algorithm, especially suitable for FPGA implementation, for fast adapting the LUT is proposed. Many design methodologies and practical implementation issues are discussed in details. Experimental results have shown that the DPD performed robustly when it is involved in the multichannel transmitter. 2) The next generation system (5G) will unquestionably use wider bandwidth to support higher throughput, which poses stringent needs for using high-speed data converters. Herein the analog-to-digital converter (ADC) tends to be the most expensive single device in the whole transmitter/receiver systems. Therefore, conventional DPD utilizing high-speed ADC becomes unaffordable, especially for small base stations (micro, pico and femto). A digital predistortion technique utilizing spectral extrapolation is proposed in this thesis, wherein with band-limited feedback signal, the requirement on ADC speed can be significantly released. Experimental results have validated the feasibility of the proposed technique for coping with band-limited feedback signal. It has been shown that adequate linearization performance can be achieved even if the acquisition bandwidth is less than the original signal bandwidth. The experimental results obtained by using LTE-Advanced signal of 320 MHz bandwidth are quite satisfactory, and to the authors’ knowledge, this is the first high-performance wideband DPD ever been reported. 3) To address the predicament that mobile operators do not have enough contiguous usable bandwidth, carrier aggregation (CA) technique is developed and imported into 4G LTE-Advanced. This pushes the utilization of concurrent dual-band transmitter/receiver, which reduces the hardware expense by using a single front-end. Compensation techniques for the respective concurrent dual-band transmitter and receiver front-ends are proposed to combat the inter-band modulation distortion, and simultaneously reduce the distortion for the both lower-side band and upper-side band signals.電気通信大学201

Methods for Model Complexity Reduction for the Nonlinear Calibration of Amplifiers Using Volterra Kernels

Volterra models allow modeling nonlinear dynamical systems, even though they require the estimation of a large number of parameters and have, consequently, potentially large computational costs. The pruning of Volterra models is thus of fundamental importance to reduce the computational costs of nonlinear calibration, and improve stability and speed, while preserving accuracy. Several techniques (LASSO, DOMP and OBS) and their variants (WLASSO and OBD) are compared in this paper for the experimental calibration of an IF amplifier. The results show that Volterra models can be simplified, yielding models that are 4–5 times sparser, with a limited impact on accuracy. About 6 dB of improved Error Vector Magnitude (EVM) is obtained, improving the dynamic range of the amplifiers. The Symbol Error Rate (SER) is greatly reduced by calibration at a large input power, and pruning reduces the model complexity without hindering SER. Hence, pruning allows improving the dynamic range of the amplifier, with almost an order of magnitude reduction in model complexity. We propose the OBS technique, used in the neural network field, in conjunction with the better known DOMP technique, to prune the model with the best accuracy. The simulations show, in fact, that the OBS and DOMP techniques outperform the others, and OBD, LASSO and WLASSO are, in turn, less efficient. A methodology for pruning in the complex domain is described, based on the Frisch–Waugh–Lovell (FWL) theorem, to separate the linear and nonlinear sections of the model. This is essential because linear models are used for equalization and cannot be pruned to preserve model generality vis-a-vis channel variations, whereas nonlinear models must be pruned as much as possible to minimize the computational overhead. This methodology can be extended to models other than the Volterra one, as the only conditions we impose on the nonlinear model are that it is feedforward and linear in the parameters