Power quality and electromagnetic compatibility: special report, session 2

The scope of Session 2 (S2) has been defined as follows by the Session Advisory Group and the Technical Committee: Power Quality (PQ), with the more general concept of electromagnetic compatibility (EMC) and with some related safety problems in electricity distribution systems. Special focus is put on voltage continuity (supply reliability, problem of outages) and voltage quality (voltage level, flicker, unbalance, harmonics). This session will also look at electromagnetic compatibility (mains frequency to 150 kHz), electromagnetic interferences and electric and magnetic fields issues. Also addressed in this session are electrical safety and immunity concerns (lightning issues, step, touch and transferred voltages). The aim of this special report is to present a synthesis of the present concerns in PQ&EMC, based on all selected papers of session 2 and related papers from other sessions, (152 papers in total). The report is divided in the following 4 blocks: Block 1: Electric and Magnetic Fields, EMC, Earthing systems Block 2: Harmonics Block 3: Voltage Variation Block 4: Power Quality Monitoring Two Round Tables will be organised: - Power quality and EMC in the Future Grid (CIGRE/CIRED WG C4.24, RT 13) - Reliability Benchmarking - why we should do it? What should be done in future? (RT 15

Diagnostic Applications for Micro-Synchrophasor Measurements

This report articulates and justifies the preliminary selection of diagnostic applications for data from micro-synchrophasors (µPMUs) in electric power distribution systems that will be further studied and developed within the scope of the three-year ARPA-e award titled Micro-synchrophasors for Distribution Systems

Time domain analysis of switching transient fields in high voltage substations

Switching operations of circuit breakers and disconnect switches generate transient currents propagating along the substation busbars. At the moment of switching, the busbars temporarily acts as antennae radiating transient electromagnetic fields within the substations. The radiated fields may interfere and disrupt normal operations of electronic equipment used within the substation for measurement, control and communication purposes. Hence there is the need to fully characterise the substation electromagnetic environment as early as the design stage of substation planning and operation to ensure safe operations of the electronic equipment. This paper deals with the computation of transient electromagnetic fields due to switching within a high voltage air-insulated substation (AIS) using the finite difference time domain (FDTD) metho

An Assessment of PIER Electric Grid Research 2003-2014 White Paper

This white paper describes the circumstances in California around the turn of the 21st century that led the California Energy Commission (CEC) to direct additional Public Interest Energy Research funds to address critical electric grid issues, especially those arising from integrating high penetrations of variable renewable generation with the electric grid. It contains an assessment of the beneficial science and technology advances of the resultant portfolio of electric grid research projects administered under the direction of the CEC by a competitively selected contractor, the University of California’s California Institute for Energy and the Environment, from 2003-2014

Design of master and slave modules on battery management system for electric vehicles

Nowadays, electric vehicle usage and the use of LiFePO4 batteries in electric vehicles gradually increase. However, there are important features to be considered to use these batteries safely and efficiently. Incorrect use of these batteries can lead to burning, explosion or shortening of the life of batteries. In this paper, a Battery Management System (BMS) for lithium based batteries is designed that operates more efficiently and communicates with UART between master and slave modules and can communicate via CAN protocol with external devices. Micro controller based control and protection equipment is designed that help to measure and monitor the voltage, temperature and current values of the batteries. They protect the battery cells from the conditions such as over charge, over discharge, high current, high temperature. BMS balances battery cell voltages during charging process with passive cell voltage balancing. In addition to the main controller module in the BMS, slave controller modules have been added to provide high resolution voltage and temperature tracking. A modular BMS has been devised which can be used in groups of batteries of different voltage values thanks to electrically isolated slave control modules

Distribution automation applications of fiber optics

Motivations for interest and research in distribution automation are discussed. The communication requirements of distribution automation are examined and shown to exceed the capabilities of power line carrier, radio, and telephone systems. A fiber optic based communication system is described that is co-located with the distribution system and that could satisfy the data rate and reliability requirements. A cost comparison shows that it could be constructed at a cost that is similar to that of a power line carrier system. The requirements for fiber optic sensors for distribution automation are discussed. The design of a data link suitable for optically-powered electronic sensing is presented. Empirical results are given. A modeling technique that was used to understand the reflections of guided light from a variety of surfaces is described. An optical position-indicator design is discussed. Systems aspects of distribution automation are discussed, in particular, the lack of interface, communications, and data standards. The economics of distribution automation are examined

A novel fault location method for a cross-bonded hv cable system based on sheath current monitoring

In order to improve the practice in the operation and maintenance of high voltage (HV) cables, this paper proposes a fault location method based on the monitoring of cable sheath currents for use in cross-bonded HV cable systems. This method first analyzes the power–frequency component of the sheath current, which can be acquired at cable terminals and cable link boxes, using a Fast Fourier Transform (FFT). The cable segment where a fault occurs can be localized by the phase difference between the sheath currents at the two ends of the cable segment, because current would flow in the opposite direction towards the two ends of the cable segment with fault. Conversely, in other healthy cable segments of the same circuit, sheath currents would flow in the same direction. The exact fault position can then be located via electromagnetic time reversal (EMTR) analysis of the fault transients of the sheath current. The sheath currents have been simulated and analyzed by assuming a single-phase short-circuit fault to occur in every cable segment of a selected cross-bonded high voltage cable circuit. The sheath current monitoring system has been implemented in a 110 kV cable circuit in China. Results indicate that the proposed method is feasible and effective in location of HV cable short circuit faults

Partial Discharge in Electronic Equipments

Tato disertační práce se věnuje studiu částečných výbojů (PD) způsobených poklesem spolehlivosti a životnosti elektronických zařízení a systémů. Diagnostika PD je dnes známá metoda pro vysoké napětí u vysoko-výkonných zařízení. V případě elektronických zařízení PD testování není ale běžně používáná metoda, přestože je zde také potenciál pro vysoké elektrické zatížení vzhledem k velmi krátké vzdálenosti. Tato práce je zaměřena na vyšetřování PD činnosti u elektronických zařízení. Bylo navrženo a provedeno pracoviště pro diagnostiku PD v elektronických zařízeních. Pracovní frekvence se pohybuje od několika stovek Hz až 100 kHz. Maximální amplituda PD testovaného napětí je vyšší než 10 kV. Navzdory jednoduché konstrukci toto zařízení přináší vysokou spolehlivost měření. Více než 300 PD testů bylo provedeno na různých elektronických zařízeních a elektronických součástí,např. na planárních transformátorech a elektronických komponentách používaných při vysoko-napěťových měničíchThis dissertation thesis is devoted to study of partial discharge (PD) caused decrease of reliability and lifetime of electronic equipments and systems. PD diagnostic is nowadays well known method for high voltage high power equipments but in case of electronic devices PD testing it is not used routinely despite that there is also a potential for high electric load due to extremely short distances. The risk of PD caused failure is here extremely high because of high working frequency and consequently high repetition rate of PD events. Therefore, this work is focused on investigation of PD activity in electronic equipments. The workplace for PD diagnostic in electronic devices based on switched power supply was designed and made. Working frequency ranges from several hundreds of Hertz up to 100 kHz. The maximal amplitude of PD testing voltage is higher than 10 kV. Despite the simple design this equipment brings high repeatability and reliability of measurement. More than 300 PD tests were made on different electronic devices and electronic components, on planar transformers, and on components for voltage gate drivers for use in high voltage power converters. Possibilities of PD tools in investigation and engineering ofd insulation systems were demonstrated.

NILM techniques for intelligent home energy management and ambient assisted living: a review

The ongoing deployment of smart meters and different commercial devices has made electricity disaggregation feasible in buildings and households, based on a single measure of the current and, sometimes, of the voltage. Energy disaggregation is intended to separate the total power consumption into specific appliance loads, which can be achieved by applying Non-Intrusive Load Monitoring (NILM) techniques with a minimum invasion of privacy. NILM techniques are becoming more and more widespread in recent years, as a consequence of the interest companies and consumers have in efficient energy consumption and management. This work presents a detailed review of NILM methods, focusing particularly on recent proposals and their applications, particularly in the areas of Home Energy Management Systems (HEMS) and Ambient Assisted Living (AAL), where the ability to determine the on/off status of certain devices can provide key information for making further decisions. As well as complementing previous reviews on the NILM field and providing a discussion of the applications of NILM in HEMS and AAL, this paper provides guidelines for future research in these topics.Agência financiadora: Programa Operacional Portugal 2020 and Programa Operacional Regional do Algarve 01/SAICT/2018/39578 Fundação para a Ciência e Tecnologia through IDMEC, under LAETA: SFRH/BSAB/142998/2018 SFRH/BSAB/142997/2018 UID/EMS/50022/2019 Junta de Comunidades de Castilla-La-Mancha, Spain: SBPLY/17/180501/000392 Spanish Ministry of Economy, Industry and Competitiveness (SOC-PLC project): TEC2015-64835-C3-2-R MINECO/FEDERinfo:eu-repo/semantics/publishedVersio

Concepts for design of an energy management system incorporating dispersed storage and generation

New forms of generation based on renewable resources must be managed as part of existing power systems in order to be utilized with maximum effectiveness. Many of these generators are by their very nature dispersed or small, so that they will be connected to the distribution part of the power system. This situation poses new questions of control and protection, and the intermittent nature of some of the energy sources poses problems of scheduling and dispatch. Under the assumption that the general objectives of energy management will remain unchanged, the impact of dispersed storage and generation on some of the specific functions of power system control and its hardware are discussed