Studies on Core-Based Testing of System-on-Chips Using Functional Bus and Network-on-Chip Interconnects

The tests of a complex system such as a microprocessor-based system-onchip (SoC) or a network-on-chip (NoC) are difficult and expensive. In this thesis, we propose three core-based test methods that reuse the existing functional interconnects-a flat bus, hierarchical buses of multiprocessor SoC's (MPSoC), and a N oC-in order to avoid the silicon area cost of a dedicated test access mechanism (TAM). However, the use of functional interconnects as functional TAM's introduces several new problems. During tests, the interconnects-including the bus arbitrator, the bus bridges, and the NoC routers-operate in the functional mode to transport the test stimuli and responses, while the core under tests (CUT) operate in the test mode. Second, the test data is transported to the CUT through the functional bus, and not directly to the test port. Therefore, special core test wrappers that can provide the necessary control signals required by the different functional interconnect are proposed. We developed two types of wrappers, one buffer-based wrapper for the bus-based systems and another pair of complementary wrappers for the NoCbased systems. Using the core test wrappers, we propose test scheduling schemes for the three functionally different types of interconnects. The test scheduling scheme for a flat bus is developed based on an efficient packet scheduling scheme that minimizes both the buffer sizes and the test time under a power constraint. The schedulingscheme is then extended to take advantage of the hierarchical bus architecture of the MPSoC systems. The third test scheduling scheme based on the bandwidth sharing is developed specifically for the NoC-based systems. The test scheduling is performed under the objective of co-optimizing the wrapper area cost and the resulting test application time using the two complementary NoC wrappers. For each of the proposed methodology for the three types of SoC architec .. ture, we conducted a thorough experimental evaluation in order to verify their effectiveness compared to other methods

Optimizing Scrubbing by Netlist Analysis for FPGA Configuration Bit Classification and Floorplanning

Existing scrubbing techniques for SEU mitigation on FPGAs do not guarantee an error-free operation after SEU recovering if the affected configuration bits do belong to feedback loops of the implemented circuits. In this paper, we a) provide a netlist-based circuit analysis technique to distinguish so-called critical configuration bits from essential bits in order to identify configuration bits which will need also state-restoring actions after a recovered SEU and which not. Furthermore, b) an alternative classification approach using fault injection is developed in order to compare both classification techniques. Moreover, c) we will propose a floorplanning approach for reducing the effective number of scrubbed frames and d), experimental results will give evidence that our optimization methodology not only allows to detect errors earlier but also to minimize the Mean-Time-To-Repair (MTTR) of a circuit considerably. In particular, we show that by using our approach, the MTTR for datapath-intensive circuits can be reduced by up to 48.5% in comparison to standard approaches

Case Study: First-Time Success ASIC Design Methodology Applied to a Multi-Processor System-on-Chip

Achieving first-time success is crucial in the ASIC design league considering the soaring cost, tight time-to-market window, and competitive business environment. One key factor in ensuring first-time success is a well-defined ASIC design methodology. Here we propose a novel ASIC design methodology that has been proven for the RUMPS401 (Rahman University Multi-Processor System 401) Multiprocessor System-on-Chip (MPSoC) project. The MPSoC project is initiated by Universiti Tunku Abdul Rahman (UTAR) VLSI design center. The proposed methodology includes the use of Universal Verification Methodology (UVM). The use of electronic design automation (EDA) software during each step of the design methodology is also presented. The first-time success RUMPS401 demonstrates the use of the proposed ASIC design methodology and the good of using one. Especially this project is carried on in educational environment that is even more limited in budget, resources and know-how, compared to the business and industrial counterparts. Here a novel ASIC design methodology that is tailored to first-time success MPSoC is presented

Testability considerations for implementing an embedded memory subsystem

textThere are a number of testability considerations for VLSI design, but test coverage, test time, accuracy of test patterns and correctness of design information for DFD (Design for debug) are the most important ones in design with embedded memories. The goal of DFT (Design-for-Test) is to achieve zero defects. When it comes to the memory subsystem in SOCs (system on chips), many flavors of memory BIST (built-in self test) are able to get high test coverage in a memory, but often, no proper attention is given to the memory interface logic (shadow logic). Functional testing and BIST are the most prevalent tests for this logic, but functional testing is impractical for complicated SOC designs. As a result, industry has widely used at-speed scan testing to detect delay induced defects. Compared with functional testing, scan-based testing for delay faults reduces overall pattern generation complexity and cost by enhancing both controllability and observability of flip-flops. However, without proper modeling of memory, Xs are generated from memories. Also, when the design has chip compression logic, the number of ATPG patterns is increased significantly due to Xs from memories. In this dissertation, a register based testing method and X prevention logic are presented to tackle these problems. An important design stage for scan based testing with memory subsystems is the step to create a gate level model and verify with this model. The flow needs to provide a robust ATPG netlist model. Most industry standard CAD tools used to analyze fault coverage and generate test vectors require gate level models. However, custom embedded memories are typically designed using a transistor-level flow, there is a need for an abstraction step to generate the gate models, which must be equivalent to the actual design (transistor level). The contribution of the research is a framework to verify that the gate level representation of custom designs is equivalent to the transistor-level design. Compared to basic stuck-at fault testing, the number of patterns for at-speed testing is much larger than for basic stuck-at fault testing. So reducing test and data volume are important. In this desertion, a new scan reordering method is introduced to reduce test data with an optimal routing solution. With in depth understanding of embedded memories and flows developed during the study of custom memory DFT, a custom embedded memory Bit Mapping method using a symbolic simulator is presented in the last chapter to achieve high yield for memories.Electrical and Computer Engineerin

Using Physical Compilation to Implement a System on Chip Platform

The goal of this thesis was to setup a complete design flow involving physical synthesis. The design chosen for this purpose was a system-on-chip (SoC) platform developed at the University of Tennessee. It involves a Leon Processor with a minimal cache configuration, an AMBA on-chip bus and an Advanced Encryption Standard module which performs decryption. As transistor size has entered the deep submicron level, iterations involved in the design cycle have increased due to the domination of interconnect delays over cell delays. Traditionally, interconnect delay has been estimated through the use of wire-load models. However, since there is no physical placement information, the delay estimation may be ineffective and result in increased iterations. Hence, placement-based synthesis has recently been introduced to provide better interconnect delay estimation. The tool used in this thesis to implement the system-on-chip design using physical synthesis is Synopsys Physical Compiler. The flow has been setup through the use of the Galaxy Reference Flow scripts obtained from Synopsys. As part of the thesis, an analysis of the differences between a physically synthesized design and a logically synthesized one in terms of area and delay is presented

Programmable flexible cores for SoC applications

Tese de mestrado. Engenharia Electrotécnica e de Computadores. Faculdade de Engenharia. Universidade do Porto. 200

System-on-Chip Design and Test with Embedded Debug Capabilities

In this project, I started with a System-on-Chip platform with embedded test structures. The baseline platform consisted of a Leon2 CPU, AMBA on-chip bus, and an Advanced Encryption Standard decryption module. The basic objective of this thesis was to use the embedded reconfigurable logic blocks for post-silicon debug and verification. The System-on-Chip platform was designed at the register transistor level and implemented in a 180-nm IBM process. Test logic instrumentation was done with DAFCA (Design Automation for Flexible Chip Architecture) Inc. pre-silicon tools. The design was then synthesized using the Synopsys Design Compiler and placed and routed using Cadence SOC Encounter. Total transistor count is about 3 million, including 1400K transistors for the debug module serving as on chip logic analyzer. Core size of the design is about 4.8mm x 4.8mm and the system is working at 151MHz. Design verification was done with Cadence NCSim. The controllability and observability of internal signals of the design is greatly increased with the help of pre-silicon tools which helps locate bugs and later fix them with the help of post-silicon tools. This helps prevent re-spins on several occasions thus saving millions of dollars. Post-silicon tools have been used to program assertions and triggers and inject numerous personalities into the reconfigurable fabric which has greatly increased the versatility of the circuit

Network-on-Chip

Addresses the Challenges Associated with System-on-Chip Integration Network-on-Chip: The Next Generation of System-on-Chip Integration examines the current issues restricting chip-on-chip communication efficiency, and explores Network-on-chip (NoC), a promising alternative that equips designers with the capability to produce a scalable, reusable, and high-performance communication backbone by allowing for the integration of a large number of cores on a single system-on-chip (SoC). This book provides a basic overview of topics associated with NoC-based design: communication infrastructure design, communication methodology, evaluation framework, and mapping of applications onto NoC. It details the design and evaluation of different proposed NoC structures, low-power techniques, signal integrity and reliability issues, application mapping, testing, and future trends. Utilizing examples of chips that have been implemented in industry and academia, this text presents the full architectural design of components verified through implementation in industrial CAD tools. It describes NoC research and developments, incorporates theoretical proofs strengthening the analysis procedures, and includes algorithms used in NoC design and synthesis. In addition, it considers other upcoming NoC issues, such as low-power NoC design, signal integrity issues, NoC testing, reconfiguration, synthesis, and 3-D NoC design. This text comprises 12 chapters and covers: The evolution of NoC from SoC—its research and developmental challenges NoC protocols, elaborating flow control, available network topologies, routing mechanisms, fault tolerance, quality-of-service support, and the design of network interfaces The router design strategies followed in NoCs The evaluation mechanism of NoC architectures The application mapping strategies followed in NoCs Low-power design techniques specifically followed in NoCs The signal integrity and reliability issues of NoC The details of NoC testing strategies reported so far The problem of synthesizing application-specific NoCs Reconfigurable NoC design issues Direction of future research and development in the field of NoC Network-on-Chip: The Next Generation of System-on-Chip Integration covers the basic topics, technology, and future trends relevant to NoC-based design, and can be used by engineers, students, and researchers and other industry professionals interested in computer architecture, embedded systems, and parallel/distributed systems

Energy aware and privacy preserving protocols for ad hoc networks with applications to disaster management

Disasters can have a serious impact on the functioning of communities and societies. Disaster management aims at providing efficient utilization of resources during pre-disaster (e.g. preparedness and prevention) and post-disaster (e.g. recovery and relief) scenarios to reduce the impact of disasters. Wireless sensors have been extensively used for early detection and prevention of disasters. However, the sensor\u27s operating environment may not always be congenial to these applications. Attackers can observe the traffic flow in the network to determine the location of the sensors and exploit it. For example, in intrusion detection systems, the information can be used to identify coverage gaps and avoid detection. Data source location privacy preservation protocols were designed in this work to address this problem. Using wireless sensors for disaster preparedness, recovery and relief operations can have high deployment costs. Making use of wireless devices (e.g. smartphones and tablets) widely available among people in the affected region is a more practical approach. Disaster preparedness involves dissemination of information among the people to make them aware of the risks they will face in the event of a disaster and how to actively prepare for them. The content is downloaded by the people on their smartphones and tablets for ubiquitous access. As these devices are primarily constrained by their available energy, this work introduces an energy-aware peer-to-peer file sharing protocol for efficient distribution of the content and maximizing the lifetime of the devices. Finally, the ability of the wireless devices to build an ad hoc network for capturing and collecting data for disaster relief and recovery operations was investigated. Specifically, novel energy-adaptive mechanisms were designed for autonomous creation of the ad hoc network, distribution of data capturing task among the devices, and collection of data with minimum delay --Abstract, page iii