Design for testability of a latch-based design

Abstract. The purpose of this thesis was to decrease the area of digital logic in a power management integrated circuit (PMIC), by replacing selected flip-flops with latches. The thesis consists of a theory part, that provides background theory for the thesis, and a practical part, that presents a latch register design and design for testability (DFT) method for achieving an acceptable level of manufacturing fault coverage for it. The total area was decreased by replacing flip-flops of read-write and one-time programmable registers with latches. One set of negative level active primary latches were shared with all the positive level active latch registers in the same register bank. Clock gating was used to select which latch register the write data was loaded to from the primary latches. The latches were made transparent during the shift operation of partial scan testing. The observability of the latch register clock gating logic was improved by leaving the first bit of each latch register as a flip-flop. The controllability was improved by inserting control points. The latch register design, developed in this thesis, resulted in a total area decrease of 5% and a register bank area decrease of 15% compared to a flip-flop-based reference design. The latch register design manages to maintain the same stuck-at fault coverage as the reference design.Salpaperäisen piirin testattavuuden suunnittelu. Tiivistelmä. Tämän opinnäytetyön tarkoituksena oli pienentää digitaalisen logiikan pinta-alaa integroidussa tehonhallintapiirissä, korvaamalla valitut kiikut salpapiireillä. Opinnäytetyö koostuu teoriaosasta, joka antaa taustatietoa opinnäytetyölle, ja käytännön osuudesta, jossa esitellään salparekisteripiiri ja testattavuussuunnittelun menetelmä, jolla saavutettiin riittävän hyvä virhekattavuus salparekisteripiirille. Kokonaispinta-alaa pienennettiin korvaamalla luku-kirjoitusrekistereiden ja kerran ohjelmoitavien rekistereiden kiikut salpapiireillä. Yhdet negatiivisella tasolla aktiiviset isäntä-salpapiirit jaettiin kaikkien samassa rekisteripankissa olevien positiivisella tasolla aktiivisten salparekistereiden kanssa. Kellon portittamisella valittiin mihin salparekisteriin kirjoitusdata ladattiin yhteisistä isäntä-salpapireistä. Osittaisessa testipolkuihin perustuvassa testauksessa salpapiirit tehtiin läpinäkyviksi siirtooperaation aikana. Salparekisterin kellon portituslogiikan havaittavuutta parannettiin jättämällä jokaisen salparekisterin ensimmäinen bitti kiikuksi. Ohjattavuutta parannettiin lisäämällä ohjauspisteitä. Salparekisteripiiri, joka suunniteltiin tässä diplomityössä, pienensi kokonaispinta-alaa 5 % ja rekisteripankin pinta-alaa 15 % verrattuna kiikkuperäiseen vertailupiiriin. Salparekisteripiiri onnistuu pitämään saman juuttumisvikamallin virhekattavuuden kuin vertailupiiri

Bascules à impulsion robustes en technologie 28nm FDSOI pour circuits numériques basse consommation à très large gamme de tension d'alimentation

The explosion market of the mobile application and the paradigm of the Internet of Things lead to a huge demand for energy-efficient systems. To overcome the limit of Moore's law due to bulk technology, a new transistor technology has appeared recently in industrial process: the fully-depleted silicon on insulator, or FDSOI.In modern ASIC designs, a large portion of the total power consumption is due to the leaves of the clock tree: the flip-flops. Therefore, the appropriate flip-flop architecture is a major choice to reach the speed and energy constraints of mobile and ultra-low power applications. After a thorough overview of the literature, the explicit pulse-triggered flip-flop topology is pointed out as a very interesting flip-flop architecture for high-speed and low-power systems. However, it is today only used in high-performances circuits mainly because of its poor robustness at ultra-low voltage.In this work, explicit pulse-triggered flip-flops architecture design is developed and studied in order to improve their robustness and their energy-efficiency. A large comparison of resettable and scannable latch architecture is performed in the energy-delay domain by modifying the sizing of the transistors, both at nominal and ultra-low voltage. Then, it is shown that the back biasing technique allowed by the FDSOI technology provides better energy and delay performances than the sizing methodology. As the pulse generator is the main cause of functional failure, we proposed a new architecture which provides both a good robustness at ultra-low voltage and an energy efficiency. A selected topology of explicit pulse-triggered flip-flop was implemented in a 16x32b register file which exhibits better speed, energy consumption and area performances than a version with master-slave flip-flops, mainly thanks to the sharing of the pulse generator over several latches.Avec l'explosion du marché des applications portables et le paradigme de l'Internet des objets, la demande pour les circuits à très haute efficacité énergétique ne cesse de croître. Afin de repousser les limites de la loi de Moore, une nouvelle technologie est apparue très récemment dans les procédés industriels afin de remplacer la technologie en substrat massif ; elle est nommée fully-depleted silicon on insulator ou FDSOI. Dans les circuits numériques synchrones modernes, une grande portion de la consommation totale du circuit provient de l'arbre d'horloge, et en particulier son extrémité : les bascules. Dès lors, l'architecture adéquate de bascules est un choix crucial pour atteindre les contraintes de vitesse et d'énergie des applications basse-consommation. Après un large aperçu de l'état de l'art, les bascules à impulsion explicite sont reconnues les plus prometteuses pour les systèmes demandant une haute performance et une basse consommation. Cependant, cette architecture est pour l'instant fortement utilisée dans les circuits à haute performance et pratiquement absente des circuits à basse tension d'alimentation, principalement à cause de sa faible robustesse face aux variations.Dans ce travail, la conception d'architecture de bascule à impulsion explicite est étudiée dans le but d'améliorer la robustesse et l'efficacité énergétique. Un large panel d'architectures de bascule, avec les fonctions reset et scan, a été comparé dans le domaine énergie-délais, à haute et basse tension d'alimentation, grâce à une méthodologie de dimensionnement des transistors. Il a été montré que la technique dite de « back bias », l'un des principaux avantages de la technologie FDSOI, permettait des meilleures performances en énergie et délais que la méthodologie de dimensionnement. Ensuite, comme le générateur d'impulsion est la principale raison de dysfonctionnement, nous avons proposé une nouvelle architecture qui permet un très bon compromis entre robustesse à faible tension et consommation énergétique. Une topologie de bascule à impulsion explicite a été choisie pour être implémentée dans un banc de registres et, comparé aux bascules maître-esclave, elle présente une plus grande vitesse, une plus faible consommation énergétique et une plus petite surface

Development of A 16:1 serializer for data transmission at 5 Gbps

Radiation tolerant, high speed and low power serializer ASIC is critical for optical link systems in particle physics experiments. Based on a commercial 0.25 μm silicon-onsapphire CMOS technology, we design a 16:1 serializer with 5 Gbps serial data rate. This ASIC has been submitted for fabrication. The post-layout simulation indicates the deterministic jitter is 54 ps (pk-pk) and random jitter is 3 ps (rms). The power consumption of the serializer is 500 mW. The design details and post layout simulation results are presented in this paper

Fully Automated Radiation Hardened by Design Circuit Construction

abstract: A fully automated logic design methodology for radiation hardened by design (RHBD) high speed logic using fine grained triple modular redundancy (TMR) is presented. The hardening techniques used in the cell library are described and evaluated, with a focus on both layout techniques that mitigate total ionizing dose (TID) and latchup issues and flip-flop designs that mitigate single event transient (SET) and single event upset (SEU) issues. The base TMR self-correcting master-slave flip-flop is described and compared to more traditional hardening techniques. Additional refinements are presented, including testability features that disable the self-correction to allow detection of manufacturing defects. The circuit approach is validated for hardness using both heavy ion and proton broad beam testing. For synthesis and auto place and route, the methodology and circuits leverage commercial logic design automation tools. These tools are glued together with custom CAD tools designed to enable easy conversion of standard single redundant hardware description language (HDL) files into hardened TMR circuitry. The flow allows hardening of any synthesizable logic at clock frequencies comparable to unhardened designs and supports standard low-power techniques, e.g. clock gating and supply voltage scaling.Dissertation/ThesisPh.D. Electrical Engineering 201

Low power VLSI design of a fir filter using dual edge triggered clocking strategy

Digital signal processing is an area of science and engineering that has developed rapidly over the past 30 years. This rapid development is a result of the significant advances in digital computer technology and integrated–circuit fabrication. DSP processors are a diverse group, most share some common features designed to support fast execution of the repetitive, numerically intensive computations characteristic of digital signal processing algorithms. The most often cited of these features is the ability to perform a multiply-accumulate operation (often called a "MAC") in a single instruction cycle. Hence in this project a DSP Processor is designed which can perform the basic DSP Operations like convolution, fourier transform and filtering. The processor designed is a simple 4-bit processor which has single data line of 8-bits and a single address bus of 16-bits. With a set of branch instructions the project DSP will operate as a CISC processor with strong math capabilities and can perform the above mentioned DSP operations. The application I have taken is the low power FIR filter using dual edge clocking strategy. It combines two novel techniques for the power reduction which is : multi stage clock gating and a symmetric two-phase level-sensitive clocking with glitch aware re-distribution of data-path registers. Simulation results confirm a 42% reduction in power over single edge triggered clocking with clock gating.Also to further reduce the power consumption the a low power latch circuit is used. Thanks to a partial pass-transistor logic, it trades time for energy, being particularly suitable for low power low-frequency applications. Simulation results confirm the power reduction. This technique discussed can be implemented to portable devices which needs longer battery life and to ASIC’

Technology Mapping, Design for Testability, and Circuit Optimizations for NULL Convention Logic Based Architectures

Delay-insensitive asynchronous circuits have been the target of a renewed research effort because of the advantages they offer over traditional synchronous circuits. Minimal timing analysis, inherent robustness against power-supply, temperature, and process variations, reduced energy consumption, less noise and EMI emission, and easy design reuse are some of the benefits of these circuits. NULL Convention Logic (NCL) is one of the mainstream asynchronous logic design paradigms that has been shown to be a promising method for designing delay-insensitive asynchronous circuits. This dissertation investigates new areas in NCL design and test and is made of three sections. The first section discusses different CMOS implementations of NCL gates and proposes new circuit techniques to enhance their operation. The second section focuses on mapping multi-rail logic expressions to a standard NCL gate library, which is a form of technology mapping for a category of NCL design automation flows. Finally, the last section proposes design for testability techniques for a recently developed low-power variant of NCL called Sleep Convention Logic (SCL)

Energy-Efficient Digital Circuit Design using Threshold Logic Gates

abstract: Improving energy efficiency has always been the prime objective of the custom and automated digital circuit design techniques. As a result, a multitude of methods to reduce power without sacrificing performance have been proposed. However, as the field of design automation has matured over the last few decades, there have been no new automated design techniques, that can provide considerable improvements in circuit power, leakage and area. Although emerging nano-devices are expected to replace the existing MOSFET devices, they are far from being as mature as semiconductor devices and their full potential and promises are many years away from being practical. The research described in this dissertation consists of four main parts. First is a new circuit architecture of a differential threshold logic flipflop called PNAND. The PNAND gate is an edge-triggered multi-input sequential cell whose next state function is a threshold function of its inputs. Second a new approach, called hybridization, that replaces flipflops and parts of their logic cones with PNAND cells is described. The resulting \hybrid circuit, which consists of conventional logic cells and PNANDs, is shown to have significantly less power consumption, smaller area, less standby power and less power variation. Third, a new architecture of a field programmable array, called field programmable threshold logic array (FPTLA), in which the standard lookup table (LUT) is replaced by a PNAND is described. The FPTLA is shown to have as much as 50% lower energy-delay product compared to conventional FPGA using well known FPGA modeling tool called VPR. Fourth, a novel clock skewing technique that makes use of the completion detection feature of the differential mode flipflops is described. This clock skewing method improves the area and power of the ASIC circuits by increasing slack on timing paths. An additional advantage of this method is the elimination of hold time violation on given short paths. Several circuit design methodologies such as retiming and asynchronous circuit design can use the proposed threshold logic gate effectively. Therefore, the use of threshold logic flipflops in conventional design methodologies opens new avenues of research towards more energy-efficient circuits.Dissertation/ThesisDoctoral Dissertation Computer Science 201

Cross-Layer Optimization for Power-Efficient and Robust Digital Circuits and Systems

With the increasing digital services demand, performance and power-efficiency become vital requirements for digital circuits and systems. However, the enabling CMOS technology scaling has been facing significant challenges of device uncertainties, such as process, voltage, and temperature variations. To ensure system reliability, worst-case corner assumptions are usually made in each design level. However, the over-pessimistic worst-case margin leads to unnecessary power waste and performance loss as high as 2.2x. Since optimizations are traditionally confined to each specific level, those safe margins can hardly be properly exploited. To tackle the challenge, it is therefore advised in this Ph.D. thesis to perform a cross-layer optimization for digital signal processing circuits and systems, to achieve a global balance of power consumption and output quality. To conclude, the traditional over-pessimistic worst-case approach leads to huge power waste. In contrast, the adaptive voltage scaling approach saves power (25% for the CORDIC application) by providing a just-needed supply voltage. The power saving is maximized (46% for CORDIC) when a more aggressive voltage over-scaling scheme is applied. These sparsely occurred circuit errors produced by aggressive voltage over-scaling are mitigated by higher level error resilient designs. For functions like FFT and CORDIC, smart error mitigation schemes were proposed to enhance reliability (soft-errors and timing-errors, respectively). Applications like Massive MIMO systems are robust against lower level errors, thanks to the intrinsically redundant antennas. This property makes it applicable to embrace digital hardware that trades quality for power savings.Comment: 190 page

Low Power Digital Filter Implementation in FPGA

Digital filters suitable for hearing aid application on low power perspective have been developed and implemented in FPGA in this dissertation. Hearing aids are primarily meant for improving hearing and speech comprehensions. Digital hearing aids score over their analog counterparts. This happens as digital hearing aids provide flexible gain besides facilitating feedback reduction and noise elimination. Recent advances in DSP and Microelectronics have led to the development of superior digital hearing aids. Many researchers have investigated several algorithms suitable for hearing aid application that demands low noise, feedback cancellation, echo cancellation, etc., however the toughest challenge is the implementation. Furthermore, the additional constraints are power and area. The device must consume as minimum power as possible to support extended battery life and should be as small as possible for increased portability. In this thesis we have made an attempt to investigate possible digital filter algorithms those are hardware configurable on low power view point. Suitability of decimation filter for hearing aid application is investigated. In this dissertation decimation filter is implemented using ‘Distributed Arithmetic’ approach.While designing this filter, it is observed that, comb-half band FIR-FIR filter design uses less hardware compared to the comb-FIR-FIR filter design. The power consumption is also less in case of comb-half band FIR-FIR filter design compared to the comb-FIR-FIR filter. This filter is implemented in Virtex-II pro board from Xilinx and the resource estimator from the system generator is used to estimate the resources. However ‘Distributed Arithmetic’ is highly serial in nature and its latency is high; power consumption found is not very low in this type of filter implementation. So we have proceeded for ‘Adaptive Hearing Aid’ using Booth-Wallace tree multiplier. This algorithm is also implemented in FPGA and power calculation of the whole system is done using Xilinx Xpower analyser. It is observed that power consumed by the hearing aid with Booth-Wallace tree multiplier is less than the hearing aid using Booth multiplier (about 25%). So we can conclude that the hearing aid using Booth-Wallace tree multiplier consumes less power comparatively. The above two approached are purely algorithmic approach. Next we proceed to combine circuit level VLSI design and with algorithmic approach for further possible reduction in power. A MAC based FDF-FIR filter (algorithm) that uses dual edge triggered latch (DET) (circuit) is used for hearing aid device. It is observed that DET based MAC FIR filter consumes less power than the traditional (single edge triggered, SET) one (about 41%). The proposed low power latch provides a power saving upto 65% in the FIR filter. This technique consumes less power compared to previous approaches that uses low power technique only at algorithmic abstraction level. The DET based MAC FIR filter is tested for real-time validation and it is observed that it works perfectly for various signals (speech, music, voice with music). The gain of the filter is tested and is found to be 27 dB (maximum) that matches with most of the hearing aid (manufacturer’s) specifications. Hence it can be concluded that FDF FIR digital filter in conjunction with low power latch is a strong candidate for hearing aid application