System-on-chip Computing and Interconnection Architectures for Telecommunications and Signal Processing

This dissertation proposes novel architectures and design techniques targeting SoC building blocks for telecommunications and signal processing applications. Hardware implementation of Low-Density Parity-Check decoders is approached at both the algorithmic and the architecture level. Low-Density Parity-Check codes are a promising coding scheme for future communication standards due to their outstanding error correction performance. This work proposes a methodology for analyzing effects of finite precision arithmetic on error correction performance and hardware complexity. The methodology is throughout employed for co-designing the decoder. First, a low-complexity check node based on the P-output decoding principle is designed and characterized on a CMOS standard-cells library. Results demonstrate implementation loss below 0.2 dB down to BER of 10^{-8} and a saving in complexity up to 59% with respect to other works in recent literature. High-throughput and low-latency issues are addressed with modified single-phase decoding schedules. A new "memory-aware" schedule is proposed requiring down to 20% of memory with respect to the traditional two-phase flooding decoding. Additionally, throughput is doubled and logic complexity reduced of 12%. These advantages are traded-off with error correction performance, thus making the solution attractive only for long codes, as those adopted in the DVB-S2 standard. The "layered decoding" principle is extended to those codes not specifically conceived for this technique. Proposed architectures exhibit complexity savings in the order of 40% for both area and power consumption figures, while implementation loss is smaller than 0.05 dB. Most modern communication standards employ Orthogonal Frequency Division Multiplexing as part of their physical layer. The core of OFDM is the Fast Fourier Transform and its inverse in charge of symbols (de)modulation. Requirements on throughput and energy efficiency call for FFT hardware implementation, while ubiquity of FFT suggests the design of parametric, re-configurable and re-usable IP hardware macrocells. In this context, this thesis describes an FFT/IFFT core compiler particularly suited for implementation of OFDM communication systems. The tool employs an accuracy-driven configuration engine which automatically profiles the internal arithmetic and generates a core with minimum operands bit-width and thus minimum circuit complexity. The engine performs a closed-loop optimization over three different internal arithmetic models (fixed-point, block floating-point and convergent block floating-point) using the numerical accuracy budget given by the user as a reference point. The flexibility and re-usability of the proposed macrocell are illustrated through several case studies which encompass all current state-of-the-art OFDM communications standards (WLAN, WMAN, xDSL, DVB-T/H, DAB and UWB). Implementations results are presented for two deep sub-micron standard-cells libraries (65 and 90 nm) and commercially available FPGA devices. Compared with other FFT core compilers, the proposed environment produces macrocells with lower circuit complexity and same system level performance (throughput, transform size and numerical accuracy). The final part of this dissertation focuses on the Network-on-Chip design paradigm whose goal is building scalable communication infrastructures connecting hundreds of core. A low-complexity link architecture for mesochronous on-chip communication is discussed. The link enables skew constraint looseness in the clock tree synthesis, frequency speed-up, power consumption reduction and faster back-end turnarounds. The proposed architecture reaches a maximum clock frequency of 1 GHz on 65 nm low-leakage CMOS standard-cells library. In a complex test case with a full-blown NoC infrastructure, the link overhead is only 3% of chip area and 0.5% of leakage power consumption. Finally, a new methodology, named metacoding, is proposed. Metacoding generates correct-by-construction technology independent RTL codebases for NoC building blocks. The RTL coding phase is abstracted and modeled with an Object Oriented framework, integrated within a commercial tool for IP packaging (Synopsys CoreTools suite). Compared with traditional coding styles based on pre-processor directives, metacoding produces 65% smaller codebases and reduces the configurations to verify up to three orders of magnitude

Dynamic reconfiguration technologies based on FPGA in software defined radio system

Partial Reconfiguration (PR) is a method for Field Programmable Gate Array (FPGA) designs which allows multiple applications to time-share a portion of an FPGA while the rest of the device continues to operate unaffected. Using this strategy, the physical layer processing architecture in Software Defined Radio (SDR) systems can benefit from reduced complexity and increased design flexibility, as different waveform applications can be grouped into one part of a single FPGA. Waveform switching often means not only changing functionality, but also changing the FPGA clock frequency. However, that is beyond the current functionality of PR processes as the clock components (such as Digital Clock Managers (DCMs)) are excluded from the process of partial reconfiguration. In this paper, we present a novel architecture that combines another reconfigurable technology, Dynamic Reconfigurable Port (DRP), with PR based on a single FPGA in order to dynamically change both functionality and also the clock frequency. The architecture is demonstrated to reduce hardware utilization significantly compared with standard, static FPGA design

An AER handshake-less modular infrastructure PCB with x8 2.5Gbps LVDS serial links

Nowadays spike-based brain processing emulation is taking off. Several EU and others worldwide projects are demonstrating this, like SpiNNaker, BrainScaleS, FACETS, or NeuroGrid. The larger the brain process emulation on silicon is, the higher the communication performance of the hosting platforms has to be. Many times the bottleneck of these system implementations is not on the performance inside a chip or a board, but in the communication between boards. This paper describes a novel modular Address-Event-Representation (AER) FPGA-based (Spartan6) infrastructure PCB (the AER-Node board) with 2.5Gbps LVDS high speed serial links over SATA cables that offers a peak performance of 32-bit 62.5Meps (Mega events per second) on board-to-board communications. The board allows back compatibility with parallel AER devices supporting up to x2 28-bit parallel data with asynchronous handshake. These boards also allow modular expansion functionality through several daughter boards. The paper is focused on describing in detail the LVDS serial interface and presenting its performance.Ministerio de Ciencia e Innovación TEC2009-10639-C04-02/01Ministerio de Economía y Competitividad TEC2012-37868-C04-02/01Junta de Andalucía TIC-6091Ministerio de Economía y Competitividad PRI-PIMCHI-2011-076

Low Latency Rendering with Dataflow Architectures

The research presented in this thesis concerns latency in VR and synthetic environments. Latency is the end-to-end delay experienced by the user of an interactive computer system, between their physical actions and the perceived response to these actions. Latency is a product of the various processing, transport and buffering delays present in any current computer system. For many computer mediated applications, latency can be distracting, but it is not critical to the utility of the application. Synthetic environments on the other hand attempt to facilitate direct interaction with a digitised world. Direct interaction here implies the formation of a sensorimotor loop between the user and the digitised world - that is, the user makes predictions about how their actions affect the world, and see these predictions realised. By facilitating the formation of the this loop, the synthetic environment allows users to directly sense the digitised world, rather than the interface, and induce perceptions, such as that of the digital world existing as a distinct physical place. This has many applications for knowledge transfer and efficient interaction through the use of enhanced communication cues. The complication is, the formation of the sensorimotor loop that underpins this is highly dependent on the fidelity of the virtual stimuli, including latency. The main research questions we ask are how can the characteristics of dataflow computing be leveraged to improve the temporal fidelity of the visual stimuli, and what implications does this have on other aspects of the fidelity. Secondarily, we ask what effects latency itself has on user interaction. We test the effects of latency on physical interaction at levels previously hypothesized but unexplored. We also test for a previously unconsidered effect of latency on higher level cognitive functions. To do this, we create prototype image generators for interactive systems and virtual reality, using dataflow computing platforms. We integrate these into real interactive systems to gain practical experience of how the real perceptible benefits of alternative rendering approaches, but also what implications are when they are subject to the constraints of real systems. We quantify the differences of our systems compared with traditional systems using latency and objective image fidelity measures. We use our novel systems to perform user studies into the effects of latency. Our high performance apparatuses allow experimentation at latencies lower than previously tested in comparable studies. The low latency apparatuses are designed to minimise what is currently the largest delay in traditional rendering pipelines and we find that the approach is successful in this respect. Our 3D low latency apparatus achieves lower latencies and higher fidelities than traditional systems. The conditions under which it can do this are highly constrained however. We do not foresee dataflow computing shouldering the bulk of the rendering workload in the future but rather facilitating the augmentation of the traditional pipeline with a very high speed local loop. This may be an image distortion stage or otherwise. Our latency experiments revealed that many predictions about the effects of low latency should be re-evaluated and experimenting in this range requires great care

Circuit design and analysis for on-FPGA communication systems

On-chip communication system has emerged as a prominently important subject in Very-Large- Scale-Integration (VLSI) design, as the trend of technology scaling favours logics more than interconnects. Interconnects often dictates the system performance, and, therefore, research for new methodologies and system architectures that deliver high-performance communication services across the chip is mandatory. The interconnect challenge is exacerbated in Field-Programmable Gate Array (FPGA), as a type of ASIC where the hardware can be programmed post-fabrication. Communication across an FPGA will be deteriorating as a result of interconnect scaling. The programmable fabrics, switches and the specific routing architecture also introduce additional latency and bandwidth degradation further hindering intra-chip communication performance. Past research efforts mainly focused on optimizing logic elements and functional units in FPGAs. Communication with programmable interconnect received little attention and is inadequately understood. This thesis is among the first to research on-chip communication systems that are built on top of programmable fabrics and proposes methodologies to maximize the interconnect throughput performance. There are three major contributions in this thesis: (i) an analysis of on-chip interconnect fringing, which degrades the bandwidth of communication channels due to routing congestions in reconfigurable architectures; (ii) a new analogue wave signalling scheme that significantly improves the interconnect throughput by exploiting the fundamental electrical characteristics of the reconfigurable interconnect structures. This new scheme can potentially mitigate the interconnect scaling challenges. (iii) a novel Dynamic Programming (DP)-network to provide adaptive routing in network-on-chip (NoC) systems. The DP-network architecture performs runtime optimization for route planning and dynamic routing which, effectively utilizes the in-silicon bandwidth. This thesis explores a new horizon in reconfigurable system design, in which new methodologies and concepts are proposed to enhance the on-FPGA communication throughput performance that is of vital importance in new technology processes

Interconnect technologies for very large spiking neural networks

In the scope of this thesis, a neural event communication architecture has been developed for use in an accelerated neuromorphic computing system and with a packet-based high performance interconnection network. Existing neuromorphic computing systems mostly use highly customised interconnection networks, directly routing single spike events to their destination. In contrast, the approach of this thesis uses a general purpose packet-based interconnection network and accumulates multiple spike events at the source node into larger network packets destined to common destinations. This is required to optimise the payload efficiency, given relatively large packet headers as compared to the size of neural spike events. Theoretical considerations are made about the efficiency of different event aggregation strategies. Thereby, important factors are the number of occurring event network-destinations and their relative frequency, as well as the number of available accumulation buffers. Based on the concept of Markov Chains, an analytical method is developed and used to evaluate these aggregation strategies. Additionally, some of these strategies are stochastically simulated in order to verify the analytical method and evaluate them beyond its applicability. Based on the results of this analysis, an optimisation strategy is proposed for the mapping of neural populations onto interconnected neuromorphic chips, as well as the joint assignment of event network-destinations to a set of accumulation buffers. During this thesis, such an event communication architecture has been implemented on the communication FPGAs in the BrainScaleS-2 accelerated neuromorphic computing system. Thereby, its usability can be scaled beyond single chip setups. For this, the EXTOLL network technology is used to transport and route the aggregated neural event packets with high bandwidth and low latency. At the FPGA, a network bandwidth of up to 12 Gbit/s is usable at a maximum payload efficiency of 94 %. The latency has been measured in the scope of this thesis to a range between 1.6 μs and 2.3 μs across the network between two neuron circuits on separate chips. This latency is thereby mostly dominated by the path from the neuromorphic chip across the communication FPGA into the network and back on the receiving side. As the EXTOLL network hardware itself is clocked at a much higher frequency than the FPGAs, the latency is expected to scale in the order of only approximately 75 ns for each additional hop through the network. For being able to globally interpret the arrival timestamps that are transmitted with every spike event, the system time counters on the FPGAs are synchronised across the network. For this, the global interrupt mechanism implemented in the EXTOLL hardware is characterised and used within this thesis. With this, a synchronisation accuracy of ±40ns could be measured. At the end of this thesis, the successful emulation of a neural signal propagation model, distributed across two BrainScaleS-2 chips and FPGAs is demonstrated using the implemented event communication architecture and the described synchronisation mechanism

Adaptive clock with useful jitter

Report - Departament Ciències de la ComputacióThe growing variability in nanoelectronic devices due to uncertainties from the manufacturing process and environmental conditions (power supply, temperature, aging) requires increasing design guardbands, forcing circuits to work with conservative clock frequencies. Various schemes for clock generation based on ring oscillators have been proposed with the goal to mitigate the power and performance losses attributable to variability. However, there has been no systematic analysis to quantify the benefits of such schemes.This paper presents and analyzes an Adaptive Clocking scheme with Useful Jitter (ACUJ) that uses variability as an opportunity to reduce power by adapting the clock frequency to the varying environmental conditions and, thus, reducing guardband margins significantly. Power can be reduced between 20% and 40% at iso-performance and performance can be boosted by similar amounts at iso-power. Additionally, energy savings can be translated to substantial advantages in terms of reliability and thermal management. More importantly, the technology can be adopted with minimal modifications to conventional EDA flows.Postprint (published version

CROSS-LAYER DESIGN, OPTIMIZATION AND PROTOTYPING OF NoCs FOR THE NEXT GENERATION OF HOMOGENEOUS MANY-CORE SYSTEMS

This thesis provides a whole set of design methods to enable and manage the runtime heterogeneity of features-rich industry-ready Tile-Based Networkon- Chips at different abstraction layers (Architecture Design, Network Assembling, Testing of NoC, Runtime Operation). The key idea is to maintain the functionalities of the original layers, and to improve the performance of architectures by allowing, joint optimization and layer coordinations. In general purpose systems, we address the microarchitectural challenges by codesigning and co-optimizing feature-rich architectures. In application-specific NoCs, we emphasize the event notification, so that the platform is continuously under control. At the network assembly level, this thesis proposes a Hold Time Robustness technique, to tackle the hold time issue in synchronous NoCs. At the network architectural level, the choice of a suitable synchronization paradigm requires a boost of synthesis flow as well as the coexistence with the DVFS. On one hand this implies the coexistence of mesochronous synchronizers in the network with dual-clock FIFOs at network boundaries. On the other hand, dual-clock FIFOs may be placed across inter-switch links hence removing the need for mesochronous synchronizers. This thesis will study the implications of the above approaches both on the design flow and on the performance and power quality metrics of the network. Once the manycore system is composed together, the issue of testing it arises. This thesis takes on this challenge and engineers various testing infrastructures. At the upper abstraction layer, the thesis addresses the issue of managing the fully operational system and proposes a congestion management technique named HACS. Moreover, some of the ideas of this thesis will undergo an FPGA prototyping. Finally, we provide some features for emerging technology by characterizing the power consumption of Optical NoC Interfaces

Asynchronous techniques for new generation variation-tolerant FPGA

PhD ThesisThis thesis presents a practical scenario for asynchronous logic implementation that would benefit the modern Field-Programmable Gate Arrays (FPGAs) technology in improving reliability. A method based on Asynchronously-Assisted Logic (AAL) blocks is proposed here in order to provide the right degree of variation tolerance, preserve as much of the traditional FPGAs structure as possible, and make use of asynchrony only when necessary or beneficial for functionality. The newly proposed AAL introduces extra underlying hard-blocks that support asynchronous interaction only when needed and at minimum overhead. This has the potential to avoid the obstacles to the progress of asynchronous designs, particularly in terms of area and power overheads. The proposed approach provides a solution that is complementary to existing variation tolerance techniques such as the late-binding technique, but improves the reliability of the system as well as reducing the design’s margin headroom when implemented on programmable logic devices (PLDs) or FPGAs. The proposed method suggests the deployment of configurable AAL blocks to reinforce only the variation-critical paths (VCPs) with the help of variation maps, rather than re-mapping and re-routing. The layout level results for this method's worst case increase in the CLB’s overall size only of 6.3%. The proposed strategy retains the structure of the global interconnect resources that occupy the lion’s share of the modern FPGA’s soft fabric, and yet permits the dual-rail iv completion-detection (DR-CD) protocol without the need to globally double the interconnect resources. Simulation results of global and interconnect voltage variations demonstrate the robustness of the method