Electronic and photonic switching in the atm era

Broadband networks require high-capacity switches in order to properly manage large amounts of traffic fluxes. Electronic and photonic technologies are being used to achieve this objective both allowing different multiplexing and switching techniques. Focusing on the asynchronous transfer mode (ATM), the inherent different characteristics of electronics and photonics makes different architectures feasible. In this paper, different switching structures are described, several ATM switching architectures which have been recently implemented are presented and the implementation characteristics discussed. Three diverse points of view are given from the electronic research, the photonic research and the commercial switches. Although all the architectures where successfully tested, they should also follow different market requirements in order to be commercialised. The characteristics are presented and the architectures projected over them to evaluate their commercial capabilities.Peer ReviewedPostprint (published version

Multilevel Parallel Communications

The research reported in this thesis investigates the use of parallelism at multiple levels to realize high-speed networks that offer advantages in throughput, cost, reliability, and flexibility over alternative approaches. This research specifically considers use of parallelism at two levels: the upper level and the lower level. At the upper level, N protocol processors perform functions included in the transport and network layers. At the lower level, M channels provide data and physical layer functions. The resulting system provides very high bandwidth to an application. A key concept of this research is the use of replicated channels to provide a single, high bandwidth channel to a single application. The parallelism provided by the network is transparent to communicating applications, thus differentiating this strategy from schemes that provide a collection of disjoint channels between applications on different nodes. Another innovative aspect of this research is that parallelism is exploited at multiple layers of the network to provide high throughput not only at the physical layer, but also at upper protocol layers. Schedulers are used to distribute data from a single stream to multiple channels and to merge data from multiple channels to reconstruct a single coherent stream. High throughput is possible by providing the combined bandwidth of multiple channels to a single source and destination through use of parallelism at multiple protocol layers. This strategy is cost effective since systems can be built using standard technologies that benefit from the economies of a broad applications base. The exotic and revolutionary components needed in non-parallel approaches to build high speed networks are not required. The replicated channels can be used to achieve high reliability as well. Multilevel parallelism is flexible since the degree of parallelism provided at any level can be matched to protocol processing demands and application requirements

Advanced manned space flight simulation and training: An investigation of simulation host computer system concepts

The findings of a preliminary investigation by Southwest Research Institute (SwRI) in simulation host computer concepts is presented. It is designed to aid NASA in evaluating simulation technologies for use in spaceflight training. The focus of the investigation is on the next generation of space simulation systems that will be utilized in training personnel for Space Station Freedom operations. SwRI concludes that NASA should pursue a distributed simulation host computer system architecture for the Space Station Training Facility (SSTF) rather than a centralized mainframe based arrangement. A distributed system offers many advantages and is seen by SwRI as the only architecture that will allow NASA to achieve established functional goals and operational objectives over the life of the Space Station Freedom program. Several distributed, parallel computing systems are available today that offer real-time capabilities for time critical, man-in-the-loop simulation. These systems are flexible in terms of connectivity and configurability, and are easily scaled to meet increasing demands for more computing power

Parallel simulation techniques for telecommunication network modelling

In this thesis, we consider the application of parallel simulation to the performance modelling of telecommunication networks. A largely automated approach was first explored using a parallelizing compiler to speed up the simulation of simple models of circuit-switched networks. This yielded reasonable results for relatively little effort compared with other approaches. However, more complex simulation models of packet- and cell-based telecommunication networks, requiring the use of discrete event techniques, need an alternative approach. A critical review of parallel discrete event simulation indicated that a distributed model components approach using conservative or optimistic synchronization would be worth exploring. Experiments were therefore conducted using simulation models of queuing networks and Asynchronous Transfer Mode (ATM) networks to explore the potential speed-up possible using this approach. Specifically, it is shown that these techniques can be used successfully to speed-up the execution of useful telecommunication network simulations. A detailed investigation has demonstrated that conservative synchronization performs very well for applications with good look ahead properties and sufficient message traffic density and, given such properties, will significantly outperform optimistic synchronization. Optimistic synchronization, however, gives reasonable speed-up for models with a wider range of such properties and can be optimized for speed-up and memory usage at run time. Thus, it is confirmed as being more generally applicable particularly as model development is somewhat easier than for conservative synchronization. This has to be balanced against the more difficult task of developing and debugging an optimistic synchronization kernel and the application models

Telemetry downlink interfaces and level-zero processing

The technical areas being investigated are as follows: (1) processing of space to ground data frames; (2) parallel architecture performance studies; and (3) parallel programming techniques. Additionally, the University administrative details and the technical liaison between New Mexico State University and Goddard Space Flight Center are addressed

Computing infrastructure issues in distributed communications systems : a survey of operating system transport system architectures

The performance of distributed applications (such as file transfer, remote login, tele-conferencing, full-motion video, and scientific visualization) is influenced by several factors that interact in complex ways. In particular, application performance is significantly affected both by communication infrastructure factors and computing infrastructure factors. Several communication infrastructure factors include channel speed, bit-error rate, and congestion at intermediate switching nodes. Computing infrastructure factors include (among other things) both protocol processing activities (such as connection management, flow control, error detection, and retransmission) and general operating system factors (such as memory latency, CPU speed, interrupt and context switching overhead, process architecture, and message buffering). Due to a several orders of magnitude increase in network channel speed and an increase in application diversity, performance bottlenecks are shifting from the network factors to the transport system factors.This paper defines an abstraction called an "Operating System Transport System Architecture" (OSTSA) that is used to classify the major components and services in the computing infrastructure. End-to-end network protocols such as TCP, TP4, VMTP, XTP, and Delta-t typically run on general-purpose computers, where they utilize various operating system resources such as processors, virtual memory, and network controllers. The OSTSA provides services that integrate these resources to support distributed applications running on local and wide area networks.A taxonomy is presented to evaluate OSTSAs in terms of their support for protocol processing activities. We use this taxonomy to compare and contrast five general-purpose commercial and experimental operating systems including System V UNIX, BSD UNIX, the x-kernel, Choices, and Xinu

Design of testbed and emulation tools

The research summarized was concerned with the design of testbed and emulation tools suitable to assist in projecting, with reasonable accuracy, the expected performance of highly concurrent computing systems on large, complete applications. Such testbed and emulation tools are intended for the eventual use of those exploring new concurrent system architectures and organizations, either as users or as designers of such systems. While a range of alternatives was considered, a software based set of hierarchical tools was chosen to provide maximum flexibility, to ease in moving to new computers as technology improves and to take advantage of the inherent reliability and availability of commercially available computing systems

Requirements for implementing real-time control functional modules on a hierarchical parallel pipelined system

Analysis of a robot control system leads to a broad range of processing requirements. One fundamental requirement of a robot control system is the necessity of a microcomputer system in order to provide sufficient processing capability.The use of multiple processors in a parallel architecture is beneficial for a number of reasons, including better cost performance, modular growth, increased reliability through replication, and flexibility for testing alternate control strategies via different partitioning. A survey of the progression from low level control synchronizing primitives to higher level communication tools is presented. The system communication and control mechanisms of existing robot control systems are compared to the hierarchical control model. The impact of this design methodology on the current robot control systems is explored