Développement des techniques de test et de diagnostic pour les FPGA hiérarchique de type mesh

The evolution trend of shrinking feature size and increasing complexity in modern electronics is being slowed down due to physical limits that generate numerous imperfections and defects during fabrication steps or projected life time of the chip. Field Programmable Gate Arrays (FPGAs) are used in complex digital systems mainly due to their reconfigurability and shorter time-to-market. To maintain a high reliability of such systems, FPGAs should be tested thoroughly for defects. FPGA architecture optimization for area saving and better signal routability is an ongoing process which directly impacts the overall FPGA testability, hence the reliability. This thesis presents a complete strategy for test and diagnosis of manufacturing defects in mesh-based FPGAs containing a novel multilevel interconnects topology which promises to provide better area and routability. Efficiency of the proposed test schemes is analyzed in terms of test cost, respective fault coverage and diagnostic resolution.L’évolution tendant à réduire la taille et augmenter la complexité des circuits électroniques modernes, est en train de ralentir du fait des limitations technologiques, qui génèrent beaucoup de d’imperfections et de defaults durant la fabrication ou la durée de vie de la puce. Les FPGAs sont utilisés dans les systèmes numériques complexes, essentiellement parce qu’ils sont reconfigurables et rapide à commercialiser. Pour garder une grande fiabilité de tels systèmes, les FPGAs doivent être testés minutieusement pour les defaults. L’optimisation de l’architecture des FPGAs pour l’économie de surface et une meilleure routabilité est un processus continue qui impacte directement la testabilité globale et de ce fait, la fiabilité. Cette thèse présente une stratégie complète pour le test et le diagnostique des defaults de fabrication des “mesh-based FPGA” contenant une nouvelle topologie d’interconnections à plusieurs niveaux, ce qui promet d’apporter une meilleure routabilité. Efficacité des schémas proposes est analysée en termes de temps de test, couverture de faute et résolution de diagnostique

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

Performance Comparison of Static CMOS and Domino Logic Style in VLSI Design: A Review

Of late, there is a steep rise in the usage of handheld gadgets and high speed applications. VLSI designers often choose static CMOS logic style for low power applications. This logic style provides low power dissipation and is free from signal noise integrity issues. However, designs based on this logic style often are slow and cannot be used in high performance circuits. On the other hand designs based on Domino logic style yield high performance and occupy less area. Yet, they have more power dissipation compared to their static CMOS counterparts. As a practice, designers during circuit synthesis, mix more than one logic style judiciously to obtain the advantages of each logic style. Carefully designing a mixed static Domino CMOS circuit can tap the advantages of both static and Domino logic styles overcoming their own short comings

Testability and redundancy techniques for improved yield and reliability of CMOS VLSI circuits

The research presented in this thesis is concerned with the design of fault-tolerant integrated circuits as a contribution to the design of fault-tolerant systems. The economical manufacture of very large area ICs will necessitate the incorporation of fault-tolerance features which are routinely employed in current high density dynamic random access memories. Furthermore, the growing use of ICs in safety-critical applications and/or hostile environments in addition to the prospect of single-chip systems will mandate the use of fault-tolerance for improved reliability. A fault-tolerant IC must be able to detect and correct all possible faults that may affect its operation. The ability of a chip to detect its own faults is not only necessary for fault-tolerance, but it is also regarded as the ultimate solution to the problem of testing. Off-line periodic testing is selected for this research because it achieves better coverage of physical faults and it requires less extra hardware than on-line error detection techniques. Tests for CMOS stuck-open faults are shown to detect all other faults. Simple test sequence generation procedures for the detection of all faults are derived. The test sequences generated by these procedures produce a trivial output, thereby, greatly simplifying the task of test response analysis. A further advantage of the proposed test generation procedures is that they do not require the enumeration of faults. The implementation of built-in self-test is considered and it is shown that the hardware overhead is comparable to that associated with pseudo-random and pseudo-exhaustive techniques while achieving a much higher fault coverage through-the use of the proposed test generation procedures. The consideration of the problem of testing the test circuitry led to the conclusion that complete test coverage may be achieved if separate chips cooperate in testing each other's untested parts. An alternative approach towards complete test coverage would be to design the test circuitry so that it is as distributed as possible and so that it is tested as it performs its function. Fault correction relies on the provision of spare units and a means of reconfiguring the circuit so that the faulty units are discarded. This raises the question of what is the optimum size of a unit? A mathematical model, linking yield and reliability is therefore developed to answer such a question and also to study the effects of such parameters as the amount of redundancy, the size of the additional circuitry required for testing and reconfiguration, and the effect of periodic testing on reliability. The stringent requirement on the size of the reconfiguration logic is illustrated by the application of the model to a typical example. Another important result concerns the effect of periodic testing on reliability. It is shown that periodic off-line testing can achieve approximately the same level of reliability as on-line testing, even when the time between tests is many hundreds of hours

The 1991 3rd NASA Symposium on VLSI Design

Papers from the symposium are presented from the following sessions: (1) featured presentations 1; (2) very large scale integration (VLSI) circuit design; (3) VLSI architecture 1; (4) featured presentations 2; (5) neural networks; (6) VLSI architectures 2; (7) featured presentations 3; (8) verification 1; (9) analog design; (10) verification 2; (11) design innovations 1; (12) asynchronous design; and (13) design innovations 2

Fault Detection Methodology for Caches in Reliable Modern VLSI Microprocessors based on Instruction Set Architectures

Η παρούσα διδακτορική διατριβή εισάγει μία χαμηλού κόστους μεθοδολογία για την ανίχνευση ελαττωμάτων σε μικρές ενσωματωμένες κρυφές μνήμες που βασίζεται σε σύγχρονες Αρχιτεκτονικές Συνόλου Εντολών και εφαρμόζεται με λογισμικό αυτοδοκιμής. Η προτεινόμενη μεθοδολογία εφαρμόζει αλγορίθμους March μέσω λογισμικού για την ανίχνευση τόσο ελαττωμάτων αποθήκευσης όταν εφαρμόζεται σε κρυφές μνήμες που περιέχουν μόνο στατικές μνήμες τυχαίας προσπέλασης όπως για παράδειγμα κρυφές μνήμες επιπέδου 1, όσο και ελαττωμάτων σύγκρισης όταν εφαρμόζεται σε κρυφές μνήμες που περιέχουν εκτός από SRAM μνήμες και μνήμες διευθυνσιοδοτούμενες μέσω περιεχομένου, όπως για παράδειγμα πλήρως συσχετιστικές κρυφές μνήμες αναζήτησης μετάφρασης. Η προτεινόμενη μεθοδολογία εφαρμόζεται και στις τρεις οργανώσεις συσχετιστικότητας κρυφής μνήμης και είναι ανεξάρτητη της πολιτικής εγγραφής στο επόμενο επίπεδο της ιεραρχίας. Η μεθοδολογία αξιοποιεί υπάρχοντες ισχυρούς μηχανισμούς των μοντέρνων ISAs χρησιμοποιώντας ειδικές εντολές, που ονομάζονται στην παρούσα διατριβή Εντολές Άμεσης Προσπέλασης Κρυφής Μνήμης (Direct Cache Access Instructions - DCAs). Επιπλέον, η προτεινόμενη μεθοδολογία εκμεταλλεύεται τους έμφυτους μηχανισμούς καταγραφής απόδοσης και τους μηχανισμούς χειρισμού παγίδων που είναι διαθέσιμοι στους σύγχρονους επεξεργαστές. Επιπρόσθετα, η προτεινόμενη μεθοδολογία εφαρμόζει την λειτουργία σύγκρισης των αλγορίθμων March όταν αυτή απαιτείται (για μνήμες CAM) και επαληθεύει το αποτέλεσμα του ελέγχου μέσω σύντομης απόκρισης, ώστε να είναι συμβατή με τις απαιτήσεις του ελέγχου εντός λειτουργίας. Τέλος, στη διατριβή προτείνεται μία βελτιστοποίηση της μεθοδολογίας για πολυνηματικές, πολυπύρηνες αρχιτεκτονικές.The present PhD thesis introduces a low cost fault detection methodology for small embedded cache memories that is based on modern Instruction Set Architectures and is applied with Software-Based Self-Test (SBST) routines. The proposed methodology applies March tests through software to detect both storage faults when applied to caches that comprise Static Random Access Memories (SRAM) only, e.g. L1 caches, and comparison faults when applied to caches that apart from SRAM memories comprise Content Addressable Memories (CAM) too, e.g. Translation Lookaside Buffers (TLBs). The proposed methodology can be applied to all three cache associativity organizations: direct mapped, set-associative and full-associative and it does not depend on the cache write policy. The methodology leverages existing powerful mechanisms of modern ISAs by utilizing instructions that we call in this PhD thesis Direct Cache Access (DCA) instructions. Moreover, our methodology exploits the native performance monitoring hardware and the trap handling mechanisms which are available in modern microprocessors. Moreover, the proposed Methodology applies March compare operations when needed (for CAM arrays) and verifies the test result with a compact response to comply with periodic on-line testing needs. Finally, a multithreaded optimization of the proposed methodology that targets multithreaded, multicore architectures is also presented in this thesi