Thermal Modelling for A Pilot Scale Pyrolytic Furnace for Production of Carbon Black

Carbon black (CB) is a very important material useful for various modern applications. There are a lot of attention currently on the extraction of a form of CB obtainable from waste tyres which is usually referred to as pyrolytic Carbon black (CBp). The authors investigated the pyrolysis process of a pyrolytic furnace built for the production of CBp using the thermal numerical principles to standardise the application. SolidWorks@ Flow Simulation software was used to replicate the process by supplying the initial conditions, the boundary conditions and the operating conditions guided by the numerical analysis. The simulated behaviour of the furnace was validated by the real-life experiments performed to produce CBp from the waste tyre

Parameters for Design and Construction of a Pilot Scale Pyrolysis Gas-Furnace

The objective of this study is to analyse the design parameters for a pyrolysis furnace designed and built for experimental purposes using the principle of heat transfer. The furnace was made of a casing of low carbon steel sheets inside which the refractory bricks were moulded, forming the furnace cavity to prevent heat loss. The pyrolysis capsule was made of high carbon steel tube with flanges which can be opened for batch loading of the precursors and evacuation of products. The furnace was designed to be gas-fired due to high efficiency and cleaner nature of gas energy. The pyrolysis capsule is installed along the centre of the furnace cavity where combustion takes place. The heat energy accumulated around the capsule is being absorbed into the pyrolysis chamber where precursors are being loaded, the regulation of the temperature of the combustion chamber via the installed feedback mechanism to monitor and control the system. The capsule has a Nitrogen gas inlet for the inert environment needed for effective pyrolysis process and an outlet duct for pyrolysis oil collection and gas recovery. The experimental initial conditions were inputted in Solidworks Flow Simulation to determine the heat distribution at different regions of the furnace and thus made it easy to determine the furnace combustion chamber temperature at which the pyrolysis temperature will be attained inside the pyrolysis chambe

Power Quality

Electrical power is becoming one of the most dominant factors in our society. Power generation, transmission, distribution and usage are undergoing signifi cant changes that will aff ect the electrical quality and performance needs of our 21st century industry. One major aspect of electrical power is its quality and stability – or so called Power Quality. The view on Power Quality did change over the past few years. It seems that Power Quality is becoming a more important term in the academic world dealing with electrical power, and it is becoming more visible in all areas of commerce and industry, because of the ever increasing industry automation using sensitive electrical equipment on one hand and due to the dramatic change of our global electrical infrastructure on the other. For the past century, grid stability was maintained with a limited amount of major generators that have a large amount of rotational inertia. And the rate of change of phase angle is slow. Unfortunately, this does not work anymore with renewable energy sources adding their share to the grid like wind turbines or PV modules. Although the basic idea to use renewable energies is great and will be our path into the next century, it comes with a curse for the power grid as power fl ow stability will suff er. It is not only the source side that is about to change. We have also seen signifi cant changes on the load side as well. Industry is using machines and electrical products such as AC drives or PLCs that are sensitive to the slightest change of power quality, and we at home use more and more electrical products with switching power supplies or starting to plug in our electric cars to charge batt eries. In addition, many of us have begun installing our own distributed generation systems on our rooft ops using the latest solar panels. So we did look for a way to address this severe impact on our distribution network. To match supply and demand, we are about to create a new, intelligent and self-healing electric power infrastructure. The Smart Grid. The basic idea is to maintain the necessary balance between generators and loads on a grid. In other words, to make sure we have a good grid balance at all times. But the key question that you should ask yourself is: Does it also improve Power Quality? Probably not! Further on, the way how Power Quality is measured is going to be changed. Traditionally, each country had its own Power Quality standards and defi ned its own power quality instrument requirements. But more and more international harmonization efforts can be seen. Such as IEC 61000-4-30, which is an excellent standard that ensures that all compliant power quality instruments, regardless of manufacturer, will produce of measurement instruments so that they can also be used in volume applications and even directly embedded into sensitive loads. But work still has to be done. We still use Power Quality standards that have been writt en decades ago and don’t match today’s technology any more, such as fl icker standards that use parameters that have been defi ned by the behavior of 60-watt incandescent light bulbs, which are becoming extinct. Almost all experts are in agreement - although we will see an improvement in metering and control of the power fl ow, Power Quality will suff er. This book will give an overview of how power quality might impact our lives today and tomorrow, introduce new ways to monitor power quality and inform us about interesting possibilities to mitigate power quality problems. Regardless of any enhancements of the power grid, “Power Quality is just compatibility” like my good old friend and teacher Alex McEachern used to say. Power Quality will always remain an economic compromise between supply and load. The power available on the grid must be suffi ciently clean for the loads to operate correctly, and the loads must be suffi ciently strong to tolerate normal disturbances on the grid

Mathematical Analysis and Thermal Modelling ofa Pilot-Scale Pyrolysis Gas Furnace

Anumerical model for the thermal operations directly related to all significant heat and mass transfer within a designed furnace chamber was developed, taking into consideration the surface area of the internal structures and surrounding furnace walls of the furnace. Some specific sets of theories on the internal and external flow of heat energy in furnaces as well as boilers were adopted and modified to exhibit a steady-state condition model for the designed gas-fired pyrolytic furnace. Existing thermal models were selected and adjusted to arrive at a unique mathematical model that was used to analyse and verify the heat distribution at different regions of the built pyrolytic furnace with the aid of the basic principles of heat and mass transfer and the associated assumptions. The distinctive numerical model formed the basis for the MATLAB Simulink program used to validate the experimental data gotten from runs of heating and cooling of the pyrolytic furnace during operation. The result of the simulated behaviour of the furnaceachieved afit to the estimation of the data of87.16%in correlation with the real experimental data. This established a thermal function that can be used asa model for potential optimisation of the pyrolysis process of the pilot furnace

STATCOM and SVC with Wind Turbines

The large wind parks are the feasible solution in order to generate clean energy compared with conventional power plants. Therefore, the interest in the Wind Energy Conversion System (WECS) is quickly increasing to reduce the fossil fuels dependencies. While the penetration of the WECS increases into the grid, many of the technical challenges have appeared. Low voltage Ride Through (LVRT) is the new requirement which needs to be fulfill when the amount of wind power generation increases, to be able to guarantee the power system reliability and stability. The voltage dips that result from faults in the grid can lead to a loss generation unit. According to the LVRT, WTs are required to be always connect during the fault, and to support the power system by supplying reactive power to ensure grid stability. The main purpose of the thesis was to investigate that how the LVRT of Doubly Fed Induction Generator (DFIG) based Wind Turbine Generator (WTG) can be enhanced using shunt connected Flexible AC Transmission System (FACTS) devices Static Synchronous Compensator (STATCOM) and Static Var Compensator (SVC). The theoretical background related to the LVRT enhancement using STATCOM and SVC is performed, and results are verified by the simulation model. This thesis is constructed in 5 Chapters, Chapter 1 gives an overview about the problems related to wind power. Chapter 2 explains the different grid codes and different topologies of the wind turbine technologies. Chapter 3 explains the working principle, construction and applications of the STATCOM and SVC. A comprehensive comparison between the STATCOM and SVC is also explained in this chapter. The operation of DFIG wind turbine during voltage dip is analyzed by using the simulation model in the next Chapter. In the first case, the effect of a three-phase fault on the power system was analyzed without using any compensation device. The LVRT requirements were not fulfilled without any compensation device. Therefore, in the second case, SVC was added in the model. Some improvement was observed in this case, but it was not enough to fulfill very strict LVRT requirements such as German Grid Codes (GGCs).Therefore, in the third case, SVC is replaced by STATCOM to meet the LVRT requirement of GGCs. In the last case, three different ratings of STATCOM were utilized to see the effect on the grid voltage and reactive power support by STATCOMs. The key findings of this thesis work are reported by Chapter 5

The 2004 NASA Faculty Fellowship Program Research Reports

This is the administrative report for the 2004 NASA Faculty Fellowship Program (NFFP) held at the George C. Marshall Space Flight Center (MSFC) for the 40th consecutive year. The NFFP offers science and engineering faculty at U.S. colleges and universities hands-on exposure to NASA s research challenges through summer research residencies and extended research opportunities at participating NASA research Centers. During this program, fellows work closely with NASA colleagues on research challenges important to NASA's strategic enterprises that are of mutual interest to the fellow and the Center. The nominal starting and .nishing dates for the 10-week program were June 1 through August 6, 2004. The program was sponsored by NASA Headquarters, Washington, DC, and operated under contract by The University of Alabama, The University of Alabama in Huntsville, and Alabama A&M University. In addition, promotion and applications are managed by the American Society for Engineering Education (ASEE) and assessment is completed by Universities Space Research Association (USRA). The primary objectives of the NFFP are to: Increase the quality and quantity of research collaborations between NASA and the academic community that contribute to the Agency s space aeronautics and space science mission. Engage faculty from colleges, universities, and community colleges in current NASA research and development. Foster a greater public awareness of NASA science and technology, and therefore facilitate academic and workforce literacy in these areas. Strengthen faculty capabilities to enhance the STEM workforce, advance competition, and infuse mission-related research and technology content into classroom teaching. Increase participation of underrepresented and underserved faculty and institutions in NASA science and technology

NASA-ASEE Summer Faculty Fellowship Program at NASA Lewis Research Center

During the summer of 1996, a ten-week Summer Faculty Fellowship Program was conducted at the NASA Lewis Research Center (LeRC) in collaboration with Case Western Reserve University (CWRU), and the Ohio Aerospace Institute (OAI). This is the thirty-third summer of this program at Lewis. It was one of nine summer programs sponsored by NASA in 1996, at various field centers under the auspices of the American Society for Engineering Education (ASEE). The objectives of the program are: (1) to further the professional knowledge of qualified engineering and science educators, (2) to stimulate an exchange of ideas between participants and NASA, (3) to enrich and refresh the research activities of participants' institutions. (4) to contribute to the research objectives of LeRC. This report is intended to recapitulate the activities comprising the 1996 Lewis Summer Faculty Fellowship Program, to summarize evaluations by the participants, and to make recommendations regarding future programs

Technology 2003: The Fourth National Technology Transfer Conference and Exposition, volume 2

Proceedings from symposia of the Technology 2003 Conference and Exposition, Dec. 7-9, 1993, Anaheim, CA, are presented. Volume 2 features papers on artificial intelligence, CAD&E, computer hardware, computer software, information management, photonics, robotics, test and measurement, video and imaging, and virtual reality/simulation

ESSE 2017. Proceedings of the International Conference on Environmental Science and Sustainable Energy

Environmental science is an interdisciplinary academic field that integrates physical-, biological-, and information sciences to study and solve environmental problems. ESSE - The International Conference on Environmental Science and Sustainable Energy provides a platform for experts, professionals, and researchers to share updated information and stimulate the communication with each other. In 2017 it was held in Suzhou, China June 23-25, 2017