Analysis And Design Optimization Of Resonant Dc-dc Converters

The development in power conversion technology is in constant demand of high power efficiency and high power density. The DC-DC power conversion is an indispensable stage for numerous power supplies and energy related applications. Particularly, in PV micro-inverters and front-end converter of power supplies, great challenges are imposed on the power performances of the DC-DC converter stage, which not only require high efficiency and density but also the capability to regulate a wide variation range of input voltage and load conditions. The resonant DC-DC converters are good candidates to meet these challenges with the advantages of achieving soft switching and low EMI. Among various resonant converter topologies, the LLC converter is very attractive for its wide gain range and providing ZVS for switches from full load to zero load condition. The operation of the LLC converter is complicated due to its multiple resonant stage mechanism. A literature review of different analysis methods are presented, and it shows that the study on the LLC is still incomplete. Therefore, an operation mode analysis method is proposed, which divides the operation into six major modes based on the occurrence of resonant stages. The resonant currents, voltages and the DC gain characteristics for each mode is investigated. To obtain a thorough view of the converter behavior, the boundaries of every mode are studied, and mode distribution regarding the gain, load and frequency is presented and discussed. As this operation mode model is a precise model, an experimental prototype is designed and built to demonstrate its accuracy in operation waveforms and gain prediction. iv Since most of the LLC modes have no closed-form solutions, simplification is necessary in order to utilize this mode model in practical design. Some prior approximation methods for converter’s gain characteristics are discussed. Instead of getting an entire gain-vs.-frequency curve, we focus on peak gains, which is an important design parameters indicating the LLC’s operating limit of input voltage and switching frequency. A numerical peak gain approximation method is developed, which provide a direct way to calculate the peak gain and its corresponding load and frequency condition. The approximated results are compared with experiments and simulations, and are proved to be accurate. In addition, as PO mode is the most favorable operation mode of the LLC, its operation region is investigated and an approximation approach is developed to determine its boundary. The design optimization of the LLC has always been a difficult problem as there are many parameters affecting the design and it lacks clear design guidance in selecting the optimal resonant tank parameters. Based on the operation mode model, three optimization methods are proposed according to the design scenarios. These methods focus on minimize the conduction loss of resonant tank while maintaining the required voltage gain level, and the approximations of peak gains and PO mode boundary can be applied here to facilitate the design. A design example is presented using one of the proposed optimization methods. As a comparison, the L-C component values are reselected and tested for the same design specifications. The experiments show that the optimal design has better efficiency performance. Finally, a generalized approach for resonant converter analysis is developed. It can be implemented by computer programs or numerical analysis tools to derive the operation waveforms and DC characteristics of resonant converter

Verification Of Non-Isolated Lcc Resonant Full Bridge Dc-Dc Converter For Solar Photovoltaic Systems

Awareness about global warming and fasting depleting fossil fuels has intensified researcher’s interest toward exploration of renewable energy resources. Among these renewable resources, photovoltaic (solar energy) is getting more attention because of its potential to be the greatest contributor of electrical energy generation. Generally DC-DC converters are used to interface solar panels with inverter which converters dc power to ac. The function of dc-dc converter is basically to step up the low dc voltage to desired higher output voltage level. Conventional switch mode dc-dc converters have problems of high switching loss and EMI. Resonant converters on the other hand have low switching loss and EMI when they operate under ZVS conditions. The aim of this research work is to explore the feasibility of a non-isolated series-parallel resonant dc-dc converter for application in PV systems. Accordingly, the working action, analysis and design procedure of series-parallel resonant full-bridge dc-dc converter is described in detail. To evaluate the performance of converter both simulation and experimental studies are carried out. First of all, converter is simulated using LT-Spice to evaluate the capability of converter to step-up dc voltage from 30V to 300V. It is shown that converter can provide desired voltage gain both for nominal and light loads with theoretical maximum efficiency up to 94%. Finally a low power laboratory prototype of the converter is built to test and evaluate the performance of the converter. The experimental results show promising performance of the converter up to 88% efficiency at 75 kHz resonance frequency. Therefore, this converter is suitable for application in PV systems where galvanic isolation is not necessary

Emerging Works on Wireless Inductive Power Transfer: AUV Charging from Constant Current Distribution and Analysis of Controls in EV Dynamic Charging

Wireless power transfer through inductive coupling, termed as inductive power transfer (IPT), is one of the important technologies in power electronics that enable transfer of power between entities without physical connections. While it has seen significant growth in the areas such as electric vehicle charging, phone charging and biomedical implants, its emerging applications include charging of autonomous underwater vehicles (AUVs) and dynamic charging of electric vehicles from the roadway. This dissertation addresses a few key challenges in these areas of IPT applications, paving the way for future developments. For the WPT for AUV, the recently developing sea-bed installed marine systems are targeted, which typically gets power from on-shore sources through constant dc low-current distribution. As the present underwater IPT topologies are not suitable for such applications, this dissertation proposes underwater IPT topologies to interface directly with such constant current distribution and provide a constant voltage output supply to the on-board systems inside the AUVs. The considerations for seawater losses and the small-signal models for control purposes are also addressed. Analysis and experimental results are provided for validations of the analytical designs and models. In the area of electric vehicle dynamic wireless power transfer (EV DWPT), the comparison of control performances of different coupler, compensation topologies and control implementations are addressed. The effect of communication latency on control bandwidth are also addressed. The outcomes are presented through analysis and simulations, and based on that future research recommendations are made to pave way for future commercial developments of well regulated and interoperable EV DWPT systems

Multiple-output DC–DC converters: applications and solutions

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required. The interest and importance of this type of multiport configuration is also reflected in that many electronics manufacturers currently develop integrated solutions. Traditionally, the different output voltages required are obtained by means of a transformer with several windings, which are in addition to providing electrical isolation. However, the current trend in the development of multiple-output DC–DC converters follows general aspects, such as low losses, high-power density, and high efficiency, as well as the development of new architectures and control strategies. Certainly, simple structures with a reduced number of components and power switches will be one of the new trends, especially to reduce the size. In this sense, the incorporation of devices with a Wide Band Gap (WBG), particularly Gallium Nitride (GaN) and Silicon Carbide (SiC), will establish future trends, advantages, and disadvantages in the development and applications of multiple-output DC–DC converters. In this paper, we present a review of the most important topics related to multiple-output DC–DC converters based on their main topologies and configurations, applications, solutions, and trends. A wide variety of configurations and topologies of multiple-output DC–DC converters are shown (more than 30), isolated and non-isolated, single and multiple switches, and based on soft and hard switching techniques, which are used in many different applications and solutions.info:eu-repo/semantics/publishedVersio

Optimization And Design Of Photovoltaic Micro-inverter

To relieve energy shortage and environmental pollution issues, renewable energy, especially PV energy has developed rapidly in the last decade. The micro-inverter systems, with advantages in dedicated PV power harvest, flexible system size, simple installation, and enhanced safety characteristics are the future development trend of the PV power generation systems. The double-stage structure which can realize high efficiency with nice regulated sinusoidal waveforms is the mainstream for the micro-inverter. This thesis studied a double stage micro-inverter system. Considering the intermittent nature of PV power, a PFC was analyzed to provide additional electrical power to the system. When the solar power is less than the load required, PFC can drag power from the utility grid. In the double stage micro-inverter, the DC/DC stage was realized by a LLC converter, which could realize soft switching automatically under frequency modulation. However it has a complicated relationship between voltage gain and load. Thus conventional variable step P&O MPPT techniques for PWM converter were no longer suitable for the LLC converter. To solve this problem, a novel MPPT was proposed to track MPP efficiently. Simulation and experimental results verified the effectiveness of the proposed MPPT. The DC/AC stage of the micro-inverter was realized by a BCM inverter. With duty cycle and frequency modulation, ZVS was achieved through controlling the inductor current bi-directional in every switching cycle. This technique required no additional resonant components and could be employed for low power applications on conventional full-bridge and half-bridge inverter topologies. Three different current mode control schemes were derived from the basic theory of the proposed technique. They were referred to as Boundary Current Mode (BCM), Variable Hysteresis Current Mode (VHCM), and Constant Hysteresis Current Mode (CHCM) individually in this paper with their advantages and disadvantages analyzed in detail. Simulation and experimental iv results demonstrated the feasibilities of the proposed soft-switching technique with the digital control schemes. The PFC converter was applied by a single stage Biflyback topology, which combined the advantages of single stage PFC and flyback topology together, with further advantages in low intermediate bus voltage and current stresses. A digital controller without current sampling requirement was proposed based on the specific topology. To reduce the voltage spike caused by the leakage inductor, a novel snubber cell combining soft switching technique with snubber technique together was proposed. Simulation and experimental waveforms illustrated the same as characteristics as the theoretical analysis. In summary, the dissertation analyzed each power stage of photovoltaic micro-inverter system from efficiency and effectiveness optimization perspectives. Moreover their advantages were compared carefully with existed topologies and control techniques. Simulation and experiment results were provided to support the theoretical analysis

Control of wireless power transfer system for dynamic charging of electric vehicles

L'abstract è presente nell'allegato / the abstract is in the attachmen

GaN-Based High Efficiency Transmitter for Multiple-Receiver Wireless Power Transfer

Wireless power transfer (WPT) has attracted great attention from industry and academia due to high charging flexibility. However, the efficiency of WPT is lower and the cost is higher than the wired power transfer approaches. Efforts including converter optimization, power delivery architecture improvement, and coils have been made to increase system efficiency.In this thesis, new power delivery architectures in the WPT of consumer electronics have been proposed to improve the overall system efficiency and increase the power density.First, a two-stage transmitter architecture is designed for a 100 W WPT system. After comparing with other topologies, the front-end ac-dc power factor correction (PFC) rectifier employs a totem-pole rectifier. A full bridge 6.78 MHz resonant inverter is designed for the subsequent stage. An impedance matching network provides constant transmitter coil current. The experimental results verify the high efficiency, high PF, and low total harmonic distortion (THD).Then, a single-stage transmitter is derived based on the verified two-stage structure. By integration of the PFC rectifier and full bridge inverter, two GaN FETs are saved and high efficiency is maintained. The integrated DCM operated PFC rectifier provides high PF and low THD. By adopting a control scheme, the transmitter coil current and power are regulated. A simple auxiliary circuit is employed to improve the light load efficiency. The experimental results verify the achievement of high efficiency.A closed-loop control scheme is implemented in the single-stage transmitter to supply multiple receivers simultaneously. With a controlled constant transmitter current, the system provides a smooth transition during dynamically load change. ZVS detection circuit is proposed to protect the transmitter from continuous hard switching operation. The control scheme is verified in the experiments.The multiple-reciever WPT system with the single-stage transmitter is investigated. The system operating range is discussed. The method of tracking optimum system efficiency is studied. The system control scheme and control procedure, targeting at providing a wide system operating range, robust operation and capability of tracking the optimized system efficiency, are proposed. Experiment results demonstrate the WPT system operation

Highly Efficient SiC Based Onboard Chargers for Plug-in Electric Vehicles

Grid-enabled plug-in electrified vehicles (PEVs) are deemed as one of the most sustainable solutions to profoundly reduce both oil consumption and greenhouse gas emissions. One of the most important realities, which will facilitate the adoption of PEVs is the method by which these vehicles will be charged. This dissertation focuses on the research of highly efficient onboard charging solutions for next generation PEVs. This dissertation designs a two-stage onboard battery charger to charge a 360 V lithium-ion battery pack. An interleaved boost topology is employed in the first stage for power factor correction (PFC) and to reduce total harmonic distortion (THD). In the second stage, a full bridge inductor-inductor-capacitor (LLC) multi-resonant converter is adopted for galvanic isolation and dc/dc conversion. Design considerations focusing on reducing the charger volume, and optimizing the conversion efficiency over the wide battery pack voltage range are investigated. The designed 1 kW Silicon based charger prototype is able to charge the battery with an output voltage range of 320 V to 420 V from 110 V, 60 Hz single-phase grid. Unity power factor, low THD, and high peak conversion efficiency have been demonstrated experimentally. This dissertation proposes a new technique to track the maximum efficiency point of LLC converter over a wide battery state-of-charge range. With the proposed variable dc link control approach, dc link voltage follows the battery pack voltage. The operating point of the LLC converter is always constrained to the proximity of the primary resonant frequency, so that the circulating losses and the turning off losses are minimized. The proposed variable dc link voltage methodology, demonstrates efficiency improvement across the wide state-of-charge range. An efficiency improvement of 2.1% at the heaviest load condition and 9.1% at the lightest load condition for LLC conversion stage are demonstrated experimentally. This dissertation proposes a novel PEV charger based on single-ended primary-inductor converter (SEPIC) and the maximum efficiency point tracking technique of an LLC converter. The proposed charger architecture demonstrates attracting features such as (1) compatible with universal grid inputs; (2) able to charge the fully depleted battery pack; (3) pulse width modulation and simplified control algorithm; and (4) the advantages of Silicon Carbide MOSFETs can be fully manifested. A 3.3 kW all Silicon Carbide based PEV charger prototype is designed to validate the proposed idea