Variability and reliability analysis of carbon nanotube technology in the presence of manufacturing imperfections

In 1925, Lilienfeld patented the basic principle of field effect transistor (FET). Thirty-four years later, Kahng and Atalla invented the MOSFET. Since that time, it has become the most widely used type of transistor in Integrated Circuits (ICs) and then the most important device in the electronics industry. Progress in the field for at least the last 40 years has followed an exponential behavior in accordance with Moore¿s Law. That is, in order to achieve higher densities and performance at lower power consumption, MOS devices have been scaled down. But this aggressive scaling down of the physical dimensions of MOSFETs has required the introduction of a wide variety of innovative factors to ensure that they could still be properly manufactured. Transistors have expe- rienced an amazing journey in the last 10 years starting with strained channel CMOS transistors at 90nm, carrying on the introduction of the high-k/metal-gate silicon CMOS transistors at 45nm until the use of the multiple-gate transistor architectures at 22nm and at recently achieved 14nm technology node. But, what technology will be able to produce sub-10nm transistors? Different novel materials and devices are being investigated. As an extension and enhancement to current MOSFETs some promising devices are n-type III-V and p-type Germanium FETs, Nanowire and Tunnel FETs, Graphene FETs and Carbon Nanotube FETs. Also, non-conventional FETs and other charge-based information carrier devices and alternative information processing devices are being studied. This thesis is focused on carbon nanotube technology as a possible option for sub-10nm transistors. In recent years, carbon nanotubes (CNTs) have been attracting considerable attention in the field of nanotechnology. They are considered to be a promising substitute for silicon channel because of their small size, unusual geometry (1D structure), and extraordinary electronic properties, including excellent carrier mobility and quasi-ballistic transport. In the same way, carbon nanotube field-effect transistors (CNFETs) could be potential substitutes for MOSFETs. Ideal CNFETs (meaning all CNTs in the transistor behave as semiconductors, have the same diameter and doping level, and are aligned and well-positioned) are predicted to be 5x faster than silicon CMOS, while consuming the same power. However, nowadays CNFETs are also affected by manufacturing variability, and several significant challenges must be overcome before these benefits can be achieved. Certain CNFET manufacturing imperfections, such as CNT diameter and doping variations, mispositioned and misaligned CNTs, high metal-CNT contact resistance, the presence of metallic CNTs (m-CNTs), and CNT density variations, can affect CNFET performance and reliability and must be addressed. The main objective of this thesis is to analyze the impact of the current CNFET manufacturing challenges on multi-channel CNFET performance from the point of view of variability and reliability and at different levels, device and circuit level. Assuming that CNFETs are not ideal or non-homogeneous because of today CNFET manufacturing imperfections, we propose a methodology of analysis that based on a CNFET ideal compact model is able to simulate heterogeneous or non-ideal CNFETs; that is, transistors with different number of tubes that have different diameters, are not uniformly spaced, have different source/drain doping levels, and, most importantly, are made up not only of semiconducting CNTs but also metallic ones. This method will allow us to analyze how CNT-specific variations affect CNFET device characteristics and parameters and CNFET digital circuit performance. Furthermore, we also derive a CNFET failure model and propose an alternative technique based on fault-tolerant architectures to deal with the presence of m-CNTs, one of the main causes of failure in CNFET circuits

Low-Power, Low-Voltage SRAM Circuits Design For Nanometric CMOS Technologies

Embedded SRAM memory is a vital component in modern SoCs. More than 80% of the System-on-Chip (SoC) die area is often occupied by SRAM arrays. As such, system reliability and yield is largely governed by the SRAM's performance and robustness. The aggressive scaling trend in CMOS device minimum feature size, coupled with the growing demand in high-capacity memory integration, has imposed the use of minimal size devices to realize a memory bitcell. The smallest 6T SRAM bitcell to date occupies a 0.1um2 in silicon area. SRAM bitcells continue to benefit from an aggressive scaling trend in CMOS technologies. Unfortunately, other system components, such as interconnects, experience a slower scaling trend. This has resulted in dramatic deterioration in a cell's ability to drive a heavily-loaded interconnects. Moreover, the growing fluctuation in device properties due to Process, Voltage, and Temperature (PVT) variations has added more uncertainty to SRAM operation. Thus ensuring the ability of a miniaturized cell to drive heavily-loaded bitlines and to generate adequate voltage swing is becoming challenging. A large percentage of state-of-the-art SoC system failures are attributed to the inability of SRAM cells to generate the targeted bitline voltage swing within a given access time. The use of read-assist mechanisms and current mode sense amplifiers are the two key strategies used to surmount bitline loading effects. On the other hand, new bitcell topologies and cell supply voltage management are used to overcome fluctuations in device properties. In this research we tackled conventional 6T SRAM bitcell limited drivability by introducing new integrated voltage sensing schemes and current-mode sense amplifiers. The proposed schemes feature a read-assist mechanism. The proposed schemes' functionality and superiority over existing schemes are verified using transient and statistical SPICE simulations. Post-layout extracted views of the devices are used for realistic simulation results. Low-voltage operated SRAM reliability and yield enhancement is investigated and a wordline boost technique is proposed as a means to manage the cell's WL operating voltage. The proposed wordline driver design shows a significant improvement in reliability and yield in a 400-mV 6T SRAM cell. The proposed wordline driver design exploit the cell's Dynamic Noise Margin (DNM), therefore boost peak level and boost decay rate programmability features are added. SPICE transient and statistical simulations are used to verify the proposed design's functionality. Finally, at a bitcell-level, we proposed a new five-transistor (5T) SRAM bitcell which shows competitive performance and reliability figures of merit compared to the conventional 6T bitcell. The functionality of the proposed cell is verified by post-layout SPICE simulations. The proposed bitcell topology is designed, implemented and fabricated in a standard ST CMOS 65nm technology process. A 1.2_ 1.2 mm2 multi-design project test chip consisting of four 32-Kbit (256-row x 128-column) SRAM macros with the required peripheral and timing control units is fabricated. Two of the designed SRAM macros are dedicated for this work, namely, a 32-Kbit 5T macro and a 32-Kbit 6T macro which is used as a comparison reference. Other macros belong to other projects and are not discussed in this document

Multi-objective Pareto front and particle swarm optimization algorithms for power dissipation reduction in microprocessors

The progress of microelectronics making possible higher integration densities, and a considerable development of on-board systems are currently undergoing, this growth comes up against a limiting factor of power dissipation. Higher power dissipation will cause an immediate spread of generated heat which causes thermal problems. Consequently, the system's total consumed energy will increase as the system temperature increase. High temperatures in microprocessors and large thermal energy of computer systems produce huge problems of system confidence, performance, and cooling expenses. Power consumed by processors are mainly due to the increase in number of cores and the clock frequency, which is dissipated in the form of heat and causes thermal challenges for chip designers. As the microprocessor’s performance has increased remarkably in Nano-meter technology, power dissipation is becoming non-negligible. To solve this problem, this article addresses power dissipation reduction issues for high performance processors using multi-objective Pareto front (PF), and particle swarm optimization (PSO) algorithms to achieve power dissipation as a prior computation that reduces the real delay of a target microprocessor unit. Simulation is verified the conceptual fundamentals and optimization of joint body and supply voltages (Vth-VDD) which showing satisfactory findings

Product assurance technology for custom LSI/VLSI electronics

The technology for obtaining custom integrated circuits from CMOS-bulk silicon foundries using a universal set of layout rules is presented. The technical efforts were guided by the requirement to develop a 3 micron CMOS test chip for the Combined Release and Radiation Effects Satellite (CRRES). This chip contains both analog and digital circuits. The development employed all the elements required to obtain custom circuits from silicon foundries, including circuit design, foundry interfacing, circuit test, and circuit qualification

Automatic Tuning of Digital Circuits.

Variation in transistors is increasing as process technology transistor dimensions shrink. Compounded with lowering supply voltage, this increased variation presents new challenges for the circuit designer. However, this variation also brings many new opportunities for the circuit designer to leverage as well. We present a time-to-digital converter embedded inside a 64-bit processor core, for direct monitoring of on-chip critical paths. This path monitoring allows the processor to monitor process variation and run-time variations. By adjusting to both static and dynamic operating conditions the impact of variations can be reduced. The time-to-digital converter achieves high-resolution measurement in the picosecond range, due to self-calibration via a self-feedback mode. This system is implemented in 45nm silicon and measured silicon results are shown. We also examine techniques for enhanced variation-tolerance in subthreshold digital circuits, applying these to a high fan-in, self-timed transition detection circuit that, due to its self-timing, is able to fully compensate for the large variation in subthreshold. In addition to mitigating variations we also leverage them for random number generation. We demonstrate that the randomness inherent in the oxide breakdown process can be extracted and applied for the specific applications of on-chip ID generation and on-chip true random number generation. By using dynamic automated self-calibrating algorithms that tune and control the on-chip circuitry, we are able to achieve extremely high-quality results. The two systems are implemented in 65 nm silicon. Measured results for the on-chip ID system, called OxID, show a high-degree of randomness and read-stability in the generated IDs, both primary prerequisites of a high-quality on-chip ID system. Measured results for the true random number generator, called OxiGen, show an exceptionally high degree of randomness, passing all fifteen NIST 800-22 tests for randomness with statistical significance and without the aid of a post-processor.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/86390/1/rachliu_1.pd

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book

Reliable Low-Power High Performance Spintronic Memories

Moores Gesetz folgend, ist es der Chipindustrie in den letzten fünf Jahrzehnten gelungen, ein explosionsartiges Wachstum zu erreichen. Dies hatte ebenso einen exponentiellen Anstieg der Nachfrage von Speicherkomponenten zur Folge, was wiederum zu speicherlastigen Chips in den heutigen Computersystemen führt. Allerdings stellen traditionelle on-Chip Speichertech- nologien wie Static Random Access Memories (SRAMs), Dynamic Random Access Memories (DRAMs) und Flip-Flops eine Herausforderung in Bezug auf Skalierbarkeit, Verlustleistung und Zuverlässigkeit dar. Eben jene Herausforderungen und die überwältigende Nachfrage nach höherer Performanz und Integrationsdichte des on-Chip Speichers motivieren Forscher, nach neuen nichtflüchtigen Speichertechnologien zu suchen. Aufkommende spintronische Spe- ichertechnologien wie Spin Orbit Torque (SOT) und Spin Transfer Torque (STT) erhielten in den letzten Jahren eine hohe Aufmerksamkeit, da sie eine Reihe an Vorteilen bieten. Dazu gehören Nichtflüchtigkeit, Skalierbarkeit, hohe Beständigkeit, CMOS Kompatibilität und Unan- fälligkeit gegenüber Soft-Errors. In der Spintronik repräsentiert der Spin eines Elektrons dessen Information. Das Datum wird durch die Höhe des Widerstandes gespeichert, welche sich durch das Anlegen eines polarisierten Stroms an das Speichermedium verändern lässt. Das Prob- lem der statischen Leistung gehen die Speichergeräte sowohl durch deren verlustleistungsfreie Eigenschaft, als auch durch ihr Standard- Aus/Sofort-Ein Verhalten an. Nichtsdestotrotz sind noch andere Probleme, wie die hohe Zugriffslatenz und die Energieaufnahme zu lösen, bevor sie eine verbreitete Anwendung finden können. Um diesen Problemen gerecht zu werden, sind neue Computerparadigmen, -architekturen und -entwurfsphilosophien notwendig. Die hohe Zugriffslatenz der Spintroniktechnologie ist auf eine vergleichsweise lange Schalt- dauer zurückzuführen, welche die von konventionellem SRAM übersteigt. Des Weiteren ist auf Grund des stochastischen Schaltvorgangs der Speicherzelle und des Einflusses der Prozessvari- ation ein nicht zu vernachlässigender Zeitraum dafür erforderlich. In diesem Zeitraum wird ein konstanter Schreibstrom durch die Bitzelle geleitet, um den Schaltvorgang zu gewährleisten. Dieser Vorgang verursacht eine hohe Energieaufnahme. Für die Leseoperation wird gleicher- maßen ein beachtliches Zeitfenster benötigt, ebenfalls bedingt durch den Einfluss der Prozess- variation. Dem gegenüber stehen diverse Zuverlässigkeitsprobleme. Dazu gehören unter An- derem die Leseintereferenz und andere Degenerationspobleme, wie das des Time Dependent Di- electric Breakdowns (TDDB). Diese Zuverlässigkeitsprobleme sind wiederum auf die benötigten längeren Schaltzeiten zurückzuführen, welche in der Folge auch einen über längere Zeit an- liegenden Lese- bzw. Schreibstrom implizieren. Es ist daher notwendig, sowohl die Energie, als auch die Latenz zur Steigerung der Zuverlässigkeit zu reduzieren, um daraus einen potenziellen Kandidaten für ein on-Chip Speichersystem zu machen. In dieser Dissertation werden wir Entwurfsstrategien vorstellen, welche das Ziel verfolgen, die Herausforderungen des Cache-, Register- und Flip-Flop-Entwurfs anzugehen. Dies erre- ichen wir unter Zuhilfenahme eines Cross-Layer Ansatzes. Für Caches entwickelten wir ver- schiedene Ansätze auf Schaltkreisebene, welche sowohl auf der Speicherarchitekturebene, als auch auf der Systemebene in Bezug auf Energieaufnahme, Performanzsteigerung und Zuver- lässigkeitverbesserung evaluiert werden. Wir entwickeln eine Selbstabschalttechnik, sowohl für die Lese-, als auch die Schreiboperation von Caches. Diese ist in der Lage, den Abschluss der entsprechenden Operation dynamisch zu ermitteln. Nachdem der Abschluss erkannt wurde, wird die Lese- bzw. Schreiboperation sofort gestoppt, um Energie zu sparen. Zusätzlich limitiert die Selbstabschalttechnik die Dauer des Stromflusses durch die Speicherzelle, was wiederum das Auftreten von TDDB und Leseinterferenz bei Schreib- bzw. Leseoperationen re- duziert. Zur Verbesserung der Schreiblatenz heben wir den Schreibstrom an der Bitzelle an, um den magnetischen Schaltprozess zu beschleunigen. Um registerbankspezifische Anforderungen zu berücksichtigen, haben wir zusätzlich eine Multiport-Speicherarchitektur entworfen, welche eine einzigartige Eigenschaft der SOT-Zelle ausnutzt, um simultan Lese- und Schreiboperatio- nen auszuführen. Es ist daher möglich Lese/Schreib- Konfilkte auf Bitzellen-Ebene zu lösen, was sich wiederum in einer sehr viel einfacheren Multiport- Registerbankarchitektur nieder- schlägt. Zusätzlich zu den Speicheransätzen haben wir ebenfalls zwei Flip-Flop-Architekturen vorgestellt. Die erste ist eine nichtflüchtige non-Shadow Flip-Flop-Architektur, welche die Speicherzelle als aktive Komponente nutzt. Dies ermöglicht das sofortige An- und Ausschalten der Versorgungss- pannung und ist daher besonders gut für aggressives Powergating geeignet. Alles in Allem zeigt der vorgestellte Flip-Flop-Entwurf eine ähnliche Timing-Charakteristik wie die konventioneller CMOS Flip-Flops auf. Jedoch erlaubt er zur selben Zeit eine signifikante Reduktion der statis- chen Leistungsaufnahme im Vergleich zu nichtflüchtigen Shadow- Flip-Flops. Die zweite ist eine fehlertolerante Flip-Flop-Architektur, welche sich unanfällig gegenüber diversen Defekten und Fehlern verhält. Die Leistungsfähigkeit aller vorgestellten Techniken wird durch ausführliche Simulationen auf Schaltkreisebene verdeutlicht, welche weiter durch detaillierte Evaluationen auf Systemebene untermauert werden. Im Allgemeinen konnten wir verschiedene Techniken en- twickeln, die erhebliche Verbesserungen in Bezug auf Performanz, Energie und Zuverlässigkeit von spintronischen on-Chip Speichern, wie Caches, Register und Flip-Flops erreichen