A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS

© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΔ fractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe

ANALYSIS AND DESIGN OF AN ULTRA-LOW POWER LOW-NOISE DTMOS BASED INSTRUMENTATION AMPLIFIER APPLIED TO THE PHYSIOLOGICAL SIGNAL ACQUISITION SYSTEM

With the rapid development of Internet of Things (IoT) technology and the popularity of portable devices, portable medical devices will become widely available soon. Physiological signal monitoring sensors are widely used for personal health management and long-term healthcare monitoring, especially for preventing acute illnesses and chronic disease monitoring for pediatric and elderly. Physiological signal monitoring sensors have the ability to monitor people's behavior in real-time for various daily activities, such as physiological signals that exhibit different waveforms and amplitudes when sleeping and awake. The real-time collected signals can be frequently compared to medical databases to detect abnormal health data for preventive healthcare. Therefore, an accurate and error-free system that provides high-quality monitoring of physiological signals is very important. Typically, an instrumentation amplifier (IA) is used for high accurate acquisition and amplification within this system. An IA with excellent performance gives patients safer health conditions and allows patients to have better health protection.This work introduces an ultra-low-power instrumentation amplifier operating at sub-0.4V voltage. Using dynamic threshold voltage MOSFET (DTMOS). The DTMOS reduces threshold voltage further and increases the driven current while the device is operating. Therefore, the DTMOS-based folded-cascode has been chosen, resulting in an increases the common-mode rejection ratio (CMRR) of the circuit while increasing the output signal swing compared over conventional topologies. The IA takes the benefit of the rail-to-rail common-mode feedback circuit and chopping to reduce flicker noise and DC offset. Reducing the chip area and power consumption leads to the output signal's high signal-to-noise ratio (SNR). The post-simulation shows that the circuit archives 45dB gain, DC to 2.07KHz operating bandwidth, and 0.8μW total power consumption. The simulated CMRR is 103dB, with 80dB power supply rejection ratio (PSRR). The simulated input reference noise is 140nV/√Hz (@100Hz) with 7.27 Noise Efficiency Factor (NEF).Keywords: Instrumentation Amplifier, DTMOS, rail-to-rail, chopping, clock boosting switch, physiological acquisition, bio-medical application

A 12-bit, 40 msamples/s, low-power, low-area pipeline analog-to-digital converter in CMOS 0.18 mum technology.

With advancements in digital signal processing in recent years, the need for high-speed, high-resolution analog-to-digital converters (ADCs) which can be used in the analog front-end has been increasing. Some examples of these applications are image and video signal processing, wireless communications and asymmetrical digital subscriber line (ADSL). In CMOS integrated circuit design, it is desirable to integrate the digital circuit and the ADC in one microchip to reduce the cost of fabrication. Consequently the power dissipation and area of the ADCs are important design factors. The original contributions in this thesis are as follows. Since the performance of pipeline ADCs significantly depends on the op-amps and comparators circuits, the performance of various comparators is analyzed and the effect of op-amp topology on the performance of pipeline ADCs is investigated. This thesis also presents a novel architecture for design of low-power and low-area pipelined ADCs which will be more useful for very low voltage applications in the future. At the schematic level, a low-power CMOS implementation of the current-mode MDAC is presented and an improved voltage comparator is designed. With the proposed design and the optimization methodology it is possible to reduce power dissipation and area compared with conventional fully differential schemes.Dept. of Electrical and Computer Engineering. Paper copy at Leddy Library: Theses & Major Papers - Basement, West Bldg. / Call Number: Thesis2004 .M64. Source: Masters Abstracts International, Volume: 43-01, page: 0281. Adviser: C. Chen. Thesis (M.A.Sc.)--University of Windsor (Canada), 2004

A Silicon Carbide Power Management Solution for High Temperature Applications

The increasing demand for discrete power devices capable of operating in high temperature and high voltage applications has spurred on the research of semiconductor materials with the potential of breaking through the limitations of traditional silicon. Gallium nitride (GaN) and silicon carbide (SiC), both of which are wide bandgap materials, have garnered the attention of researchers and gradually gained market share. Although these wide bandgap power devices enable more ambitious commercial applications compared to their silicon-based counterparts, reaching their potential is contingent upon developing integrated circuits (ICs) capable of operating in similar environments. The foundation of any electrical system is the ability to efficiently condition and supply power. The work presented in this thesis explores integrated SiC power management solutions in the form of linear regulators and switched capacitor converters. While switched-mode converters provide high efficiency, the requirement of an inductor hinders the development of a compact, integrated solution that can endure harsh operating environments. Although the primary research motivation for wide bandgap ICs has been to provide control and protection circuitry for power devices, the circuitry designed in this work can be incorporated in stand-alone applications as well. Battery or generator powered data acquisition systems targeted towards monitoring industrial machinery is one potential usage scenario

Energy Efficiency in Communications and Networks

The topic of "Energy Efficiency in Communications and Networks" attracts growing attention due to economical and environmental reasons. The amount of power consumed by information and communication technologies (ICT) is rapidly increasing, as well as the energy bill of service providers. According to a number of studies, ICT alone is responsible for a percentage which varies from 2% to 10% of the world power consumption. Thus, driving rising cost and sustainability concerns about the energy footprint of the IT infrastructure. Energy-efficiency is an aspect that until recently was only considered for battery driven devices. Today we see energy-efficiency becoming a pervasive issue that will need to be considered in all technology areas from device technology to systems management. This book is seeking to provide a compilation of novel research contributions on hardware design, architectures, protocols and algorithms that will improve the energy efficiency of communication devices and networks and lead to a more energy proportional technology infrastructure

Performance enhancement techniques for operational amplifiers

Operational amplifiers (op amps) are one of the most fundamental and widely used building blocks for analog and mixed-signal circuits and systems. As transistors’ feature size scales down in the deep submicron process, the short channel effects, high leakage current and reduced supply voltages make the design of op amps more challenging. In this dissertation, we present several methods to improve op amps’ DC gain, slew rate, power efficiency and current utilization efficiency (CUE). A basic requirement for an op amp is high DC gain especially for high precision applications. We introduce a method to robustly improve op amps’ DC gain with negligible power and area overhead. The new DC gain enhancement method can be implemented based on the source degeneration circuit (SDC) or the flipped voltage attenuator (FVA). Compared to the FVA-based technique, the SDC-based technique is more suitable for those CMOS processes whose transistors’ threshold voltages are too low for the transistors in the FVA to work in weak or strong inversion regions. Otherwise, the FVA-based technique is recommended as this technique is more robust to devices’ random mismatch. A prototype op amp with the FVA-based technique is designed and fabricated in the IBM130nm process. The measurement and simulation results of the prototype verify that the technique largely enhances an op amp’s DC and is very robust over process, voltage and temperature variations. Another important op amp requirement is high slew rate. In this regard, we introduce a method that greatly improves an op amp’s slew rate while still preserving its small signal performance by a well-defined turn-on condition. The performance of the introduced method is discussed in comparison with an existing adaptive biasing method that was widely used to enhance slew rate. The introduced method excels in several aspects. First, unlike the adaptive biasing method which degrades an op amp’ linearity, the introduced method is able to enhance linearity. Second, the proposed method improves an op amp’s slew rate by 2320% (vs. 780% by the adaptive method) with the power and area overhead of 2% and 1.2% (vs. 15% and 35% by the adaptive method). In addition, the proposed method improves the op amp’s total harmonic distortion (THD) by 6dB but the adaptive method degrades the THD by 12dB. The ability to drive large capacitive loads is becoming critical for op amps in emerging applications such as liquid crystal display drivers. In this regard, we introduce a power efficient design of op amps that can drive large capacitive loads. The proposed method decouples the large and small signal performance, eliminates current waste in the preamp stages’ load circuits, and is not sensitive to devices’ random mismatches. Compared to the state-of-the-art methods, our design prototype in a CMOS 180nm process shows largely improved small and large signal figure of merits, equivalent to largely improved power efficiency for given small and large signal performance specifications. Folded cascode amplifier (FCA) is a commonly used architecture for designing op amps, but a significant portion of supply current is wasted in the cascode stage. This not only reduces the current utilization efficiency (CUE), defined as the ratio of an FCA’s tail current to its total supply current, but also degrades the FCA’s gain, noise and offset. In this regard, we introduce a method to dramatically reduce a FCA’s cascode stage current without degrading the FCA’s settling performance. Compared to the existing methods, the proposed method effectively improves not only the CUE but also the settling performance of op amps. Lastly, a prototype FCA, with the proposed performance enhancement techniques of gain, slew rate and CUE, is designed to demonstrate the compatibility of these techniques

Low-power switched capacitor voltage reference

Low-power analog design represents a developing technological trend as it emerges from a rather limited range of applications to a much wider arena affecting mainstream market segments. It especially affects portable electronics with respect to battery life, performance, and physical size. Meanwhile, low-power analog design enables technologies such as sensor networks and RFID. Research opportunities abound to exploit the potential of low power analog design, apply low-power to established fields, and explore new applications. The goal of this effort is to design a low-power reference circuit that delivers an accurate reference with very minimal power consumption. The circuit and device level low-power design techniques are suitable for a wide range of applications. To meet this goal, switched capacitor bandgap architecture was chosen. It is the most suitable for developing a systematic, and groundup, low-power design approach. In addition, the low-power analog cell library developed would facilitate building a more complex low-power system. A low-power switched capacitor bandgap was designed, fabricated, and fully tested. The bandgap generates a stable 0.6-V reference voltage, in both the discrete-time and continuous-time domain. The system was thoroughly tested and individual building blocks were characterized. The reference voltage is temperature stable, with less than a 100 ppm/°C drift, over a --60 dB power supply rejection, and below a 1 [Mu]A total supply current (excluding optional track-and-hold). Besides using it as a voltage reference, potential applications are also described using derivatives of this switched capacitor bandgap, specifically supply supervisory and on-chip thermal regulation

Performance enhancement in the desing of amplifier and amplifier-less circuits in modern CMOS technologies.

In the context of nowadays CMOS technology downscaling and the increasing demand of high performance electronics by industry and consumers, analog design has become a major challenge. On the one hand, beyond others, amplifiers have traditionally been a key cell for many analog systems whose overall performance strongly depends on those of the amplifier. Consequently, still today, achieving high performance amplifiers is essential. On the other hand, due to the increasing difficulty in achieving high performance amplifiers in downscaled modern technologies, a different research line that replaces the amplifier by other more easily achievable cells appears: the so called amplifier-less techniques. This thesis explores and contributes to both philosophies. Specifically, a lowvoltage differential input pair is proposed, with which three multistage amplifiers in the state of art are designed, analysed and tested. Moreover, a structure for the implementation of differential switched capacitor circuits, specially suitable for comparator-based circuits, that features lower distortion and less noise than the classical differential structures is proposed, an, as a proof of concept, implemented in a ΔΣ modulator