Geometrically-constrained, parasitic-aware synthesis of analog ICs

In order to speed up the design process of analog ICs, iterations between different design stages should be avoided as much as possible. More specifically, spins between electrical and physical synthesis should be reduced for this is a very time-consuming task: if circuit performance including layout-induced degradations proves unacceptable, a re-design cycle must be entered, and electrical, physical, or both synthesis processes, would have to be repeated. It is also worth noting that if geometric optimization (e.g., area minimization) is undertaken after electrical synthesis, it may add up as another source of unexpected degradation of the circuit performance due to the impact of the geometric variables (e.g., transistor folds) on the device and the routing parasitic values. This awkward scenario is caused by the complete separation of said electrical and physical synthesis, a design practice commonly followed so far. Parasitic-aware synthesis, consisting in including parasitic estimates to the circuit netlist directly during electrical synthesis, has been proposed as solution. While most of the reported contributions either tackle parasitic-aware synthesis without paying special attention to geometric optimization or approach both issues only partially, this paper addresses the problem in a unified way. In what has been called layout-aware electrical synthesis, a simulation-based optimization algorithm explores the design space with geometric variables constrained to meet certain user-defined goals, which provides reliable estimates of layout-induced parasitics at each iteration, and, thereby, accurate evaluation of the circuit ultimate performance. This technique, demonstrated here through several design examples, requires knowing layout details beforehand; to facilitate this, procedural layout generation is used as physical synthesis approach due to its rapidness and ability to capture analog layout know-how.Ministerio de Educación y Ciencia TEC2004-0175

A framework for fine-grain synthesis optimization of operational amplifiers

This thesis presents a cell-level framework for Operational Amplifiers Synthesis (OASYN) coupling both circuit design and layout. For circuit design, the tool applies a corner-driven optimization, accounting for on-chip performance variations. By exploring the process, voltage, and temperature variations space, the tool extracts design worst case solution. The tool undergoes sensitivity analysis along with Pareto-optimality to achieve required specifications. For layout phase, OASYN generates a DRC proved automated layout based on a sized circuit-level description. Morata et al. (1996) introduced an elegant representation of block placement called sequence pair for general floorplans (SP). Like TCG and BSG, but unlike O-tree, B*tree, and CBL, SP is P-admissible. Unlike SP, TCG supports incremental update during operation and keeps the information of the boundary modules as well as their relative positions in the representation. Block placement algorithms that are based on SP use heuristic optimization algorithms, e.g., simulated annealing where generation of large number of sequence pairs are required. Therefore a fast algorithm is needed to generate sequence pairs after each solution perturbation. The thesis presents a new simple and efficient O(n) runtime algorithm for fast realization of incremental update for cost evaluation. The algorithm integrates sequence pair and transitive closure graph advantages into TCG-S* a superior topology update scheme which facilitates the search for optimum desired floorplan. Experiments show that TCG-S* is better than existing works in terms of area utilization and convergence speed. Routing-aware placement is implemented in OASYN, handling symmetry constraints, e.g., interdigitization, common centroid, along with congestion elimination and the enhancement of placement routability

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi.Postprint (published version

Layoutautomatisierung im analogen IC-Entwurf mit formalisiertem und nicht-formalisiertem Expertenwissen

After more than three decades of electronic design automation, most layouts for analog integrated circuits are still handcrafted in a laborious manual fashion today. Obverse to the highly automated synthesis tools in the digital domain (coping with the quantitative difficulty of packing more and more components onto a single chip – a desire well known as More Moore), analog layout automation struggles with the many diverse and heavily correlated functional requirements that turn the analog design problem into a More than Moore challenge. Facing this qualitative complexity, seasoned layout engineers rely on their comprehensive expert knowledge to consider all design constraints that uncompromisingly need to be satisfied. This usually involves both formally specified and nonformally communicated pieces of expert knowledge, which entails an explicit and implicit consideration of design constraints, respectively. Existing automation approaches can be basically divided into optimization algorithms (where constraint consideration occurs explicitly) and procedural generators (where constraints can only be taken into account implicitly). As investigated in this thesis, these two automation strategies follow two fundamentally different paradigms denoted as top-down automation and bottom-up automation. The major trait of top-down automation is that it requires a thorough formalization of the problem to enable a self-intelligent solution finding, whereas a bottom-up automatism –controlled by parameters– merely reproduces solutions that have been preconceived by a layout expert in advance. Since the strengths of one paradigm may compensate the weaknesses of the other, it is assumed that a combination of both paradigms –called bottom-up meets top-down– has much more potential to tackle the analog design problem in its entirety than either optimization-based or generator-based approaches alone. Against this background, the thesis at hand presents Self-organized Wiring and Arrangement of Responsive Modules (SWARM), an interdisciplinary methodology addressing the design problem with a decentralized multi-agent system. Its basic principle, similar to the roundup of a sheep herd, is to let responsive mobile layout modules (implemented as context-aware procedural generators) interact with each other inside a user-defined layout zone. Each module is allowed to autonomously move, rotate and deform itself, while a supervising control organ successively tightens the layout zone to steer the interaction towards increasingly compact (and constraint compliant) layout arrangements. Considering various principles of self-organization and incorporating ideas from existing decentralized systems, SWARM is able to evoke the phenomenon of emergence: although each module only has a limited viewpoint and selfishly pursues its personal objectives, remarkable overall solutions can emerge on the global scale. Several examples exhibit this emergent behavior in SWARM, and it is particularly interesting that even optimal solutions can arise from the module interaction. Further examples demonstrate SWARM’s suitability for floorplanning purposes and its application to practical place-and-route problems. The latter illustrates how the interacting modules take care of their respective design requirements implicitly (i.e., bottom-up) while simultaneously paying respect to high level constraints (such as the layout outline imposed top-down by the supervising control organ). Experimental results show that SWARM can outperform optimization algorithms and procedural generators both in terms of layout quality and design productivity. From an academic point of view, SWARM’s grand achievement is to tap fertile virgin soil for future works on novel bottom-up meets top-down automatisms. These may one day be the key to close the automation gap in analog layout design.Nach mehr als drei Jahrzehnten Entwurfsautomatisierung werden die meisten Layouts für analoge integrierte Schaltkreise heute immer noch in aufwändiger Handarbeit entworfen. Gegenüber den hochautomatisierten Synthesewerkzeugen im Digitalbereich (die sich mit dem quantitativen Problem auseinandersetzen, mehr und mehr Komponenten auf einem einzelnen Chip unterzubringen – bestens bekannt als More Moore) kämpft die analoge Layoutautomatisierung mit den vielen verschiedenen und stark korrelierten funktionalen Anforderungen, die das analoge Entwurfsproblem zu einer More than Moore Herausforderung machen. Angesichts dieser qualitativen Komplexität bedarf es des umfassenden Expertenwissens erfahrener Layouter um sämtliche Entwurfsconstraints, die zwingend eingehalten werden müssen, zu berücksichtigen. Meist beinhaltet dies formal spezifiziertes als auch nicht-formal übermitteltes Expertenwissen, was eine explizite bzw. implizite Constraint Berücksichtigung nach sich zieht. Existierende Automatisierungsansätze können grundsätzlich unterteilt werden in Optimierungsalgorithmen (wo die Constraint Berücksichtigung explizit erfolgt) und prozedurale Generatoren (die Constraints nur implizit berücksichtigen können). Wie in dieser Arbeit eruiert wird, folgen diese beiden Automatisierungsstrategien zwei grundlegend unterschiedlichen Paradigmen, bezeichnet als top-down Automatisierung und bottom-up Automatisierung. Wesentliches Merkmal der top-down Automatisierung ist die Notwendigkeit einer umfassenden Problemformalisierung um eine eigenintelligente Lösungsfindung zu ermöglichen, während ein bottom-up Automatismus –parametergesteuert– lediglich Lösungen reproduziert, die vorab von einem Layoutexperten vorgedacht wurden. Da die Stärken des einen Paradigmas die Schwächen des anderen ausgleichen können, ist anzunehmen, dass eine Kombination beider Paradigmen –genannt bottom-up meets top down– weitaus mehr Potenzial hat, das analoge Entwurfsproblem in seiner Gesamtheit zu lösen als optimierungsbasierte oder generatorbasierte Ansätze für sich allein. Vor diesem Hintergrund stellt die vorliegende Arbeit Self-organized Wiring and Arrangement of Responsive Modules (SWARM) vor, eine interdisziplinäre Methodik, die das Entwurfsproblem mit einem dezentralisierten Multi-Agenten-System angeht. Das Grundprinzip besteht darin, ähnlich dem Zusammentreiben einer Schafherde, reaktionsfähige mobile Layoutmodule (realisiert als kontextbewusste prozedurale Generatoren) in einer benutzerdefinierten Layoutzone interagieren zu lassen. Jedes Modul darf sich selbständig bewegen, drehen und verformen, wobei ein übergeordnetes Kontrollorgan die Zone schrittweise verkleinert, um die Interaktion auf zunehmend kompakte (und constraintkonforme) Layoutanordnungen hinzulenken. Durch die Berücksichtigung diverser Selbstorganisationsgrundsätze und die Einarbeitung von Ideen bestehender dezentralisierter Systeme ist SWARM in der Lage, das Phänomen der Emergenz hervorzurufen: obwohl jedes Modul nur eine begrenzte Sichtweise hat und egoistisch seine eigenen Ziele verfolgt, können sich auf globaler Ebene bemerkenswerte Gesamtlösungen herausbilden. Mehrere Beispiele veranschaulichen dieses emergente Verhalten in SWARM, wobei besonders interessant ist, dass sogar optimale Lösungen aus der Modulinteraktion entstehen können. Weitere Beispiele demonstrieren SWARMs Eignung zwecks Floorplanning sowie die Anwendung auf praktische Place-and-Route Probleme. Letzteres verdeutlicht, wie die interagierenden Module ihre jeweiligen Entwurfsanforderungen implizit (also: bottom-up) beachten, während sie gleichzeitig High-Level-Constraints berücksichtigen (z.B. die Layoutkontur, die top-down vom übergeordneten Kontrollorgan auferlegt wird). Experimentelle Ergebnisse zeigen, dass Optimierungsalgorithmen und prozedurale Generatoren von SWARM sowohl bezüglich Layoutqualität als auch Entwurfsproduktivität übertroffen werden können. Aus akademischer Sicht besteht SWARMs große Errungenschaft in der Erschließung fruchtbaren Neulands für zukünftige Arbeiten an neuartigen bottom-up meets top-down Automatismen. Diese könnten eines Tages der Schlüssel sein, um die Automatisierungslücke im analogen Layoutentwurf zu schließen

Cross-Layer Pathfinding for Off-Chip Interconnects

Off-chip interconnects for integrated circuits (ICs) today induce a diverse design space, spanning many different applications that require transmission of data at various bandwidths, latencies and link lengths. Off-chip interconnect design solutions are also variously sensitive to system performance, power and cost metrics, while also having a strong impact on these metrics. The costs associated with off-chip interconnects include die area, package (PKG) and printed circuit board (PCB) area, technology and bill of materials (BOM). Choices made regarding off-chip interconnects are fundamental to product definition, architecture, design implementation and technology enablement. Given their cross-layer impact, it is imperative that a cross-layer approach be employed to architect and analyze off-chip interconnects up front, so that a top-down design flow can comprehend the cross-layer impacts and correctly assess the system performance, power and cost tradeoffs for off-chip interconnects. Chip architects are not exposed to all the tradeoffs at the physical and circuit implementation or technology layers, and often lack the tools to accurately assess off-chip interconnects. Furthermore, the collaterals needed for a detailed analysis are often lacking when the chip is architected; these include circuit design and layout, PKG and PCB layout, and physical floorplan and implementation. To address the need for a framework that enables architects to assess the system-level impact of off-chip interconnects, this thesis presents power-area-timing (PAT) models for off-chip interconnects, optimization and planning tools with the appropriate abstraction using these PAT models, and die/PKG/PCB co-design methods that help expose the off-chip interconnect cross-layer metrics to the die/PKG/PCB design flows. Together, these models, tools and methods enable cross-layer optimization that allows for a top-down definition and exploration of the design space and helps converge on the correct off-chip interconnect implementation and technology choice. The tools presented cover off-chip memory interfaces for mobile and server products, silicon photonic interfaces, 2.5D silicon interposers and 3D through-silicon vias (TSVs). The goal of the cross-layer framework is to assess the key metrics of the interconnect (such as timing, latency, active/idle/sleep power, and area/cost) at an appropriate level of abstraction by being able to do this across layers of the design flow. In additional to signal interconnect, this thesis also explores the need for such cross-layer pathfinding for power distribution networks (PDN), where the system-on-chip (SoC) floorplan and pinmap must be optimized before the collateral layouts for PDN analysis are ready. Altogether, the developed cross-layer pathfinding methodology for off-chip interconnects enables more rapid and thorough exploration of a vast design space of off-chip parallel and serial links, inter-die and inter-chiplet links and silicon photonics. Such exploration will pave the way for off-chip interconnect technology enablement that is optimized for system needs. The basis of the framework can be extended to cover other interconnect technology as well, since it fundamentally relates to system-level metrics that are common to all off-chip interconnects

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

High-Performance Fpaa Design For Hierarchical Implementation Of Analog And Mixed-Signal Systems

The design complexity of today's IC has increased dramatically due to the high integration allowed by advanced CMOS VLSI process. A key to manage the increased design complexity while meeting the shortening time-to-market is design automation. In digital world, the field-programmable gate arrays (FPGAs) have evolved to play a very important role by providing ASIC-compatible design methodologies that include design-for-testability, design optimization and rapid prototyping. On the analog side, the drive towards shorter design cycles has demanded the development of high performance analog circuits that are configurable and suitable for CAD methodologies. Field-programmable analog arrays (FPAAs) are intended to achieve the benefits for analog system design as FPGAs have in the digital field. Despite of the obvious advantages of hierarchical analog design, namely short time-to-market and low non-recurring engineering (NRE) costs, this approach has some apparent disadvantages. The redundant devices and routing resources for programmability requires extra chip area, while switch and interconnect parasitics cause considerable performance degradation. To deliver a high-performance FPAA, effective methodologies must be developed to minimize those adversary effects. In this dissertation, three important aspects in the FPAA design are studied to achieve that goal: the programming technology, the configurable analog block (CAB) design and the routing architecture design. Enabled by the Laser MakelinkTM technology, which provides nearly ideal programmable switches, channel segmentation algorithms are developed to improve channel routability and reduce interconnect parasitics. Segmented routing are studied and performance metrics accounting for interconnect parasitics are proposed for performance-driven analog routing. For large scale arrays, buffer insertions are considered to further reduce interconnection delay and cross-coupling noise. A high-performance, highly flexible CAB is developed to realized both continuous-mode and switched-capacitor circuits. In the end, the implementation of an 8-bit, 50MSPS pipelined A/D converter using the proposed FPAA is presented as an example of the hierarchical analog design approach, with its key performance specifications discussed