A review of RFI mitigation techniques in microwave radiometry

Radio frequency interference (RFI) is a well-known problem in microwave radiometry (MWR). Any undesired signal overlapping the MWR protected frequency bands introduces a bias in the measurements, which can corrupt the retrieved geophysical parameters. This paper presents a literature review of RFI detection and mitigation techniques for microwave radiometry from space. The reviewed techniques are divided between real aperture and aperture synthesis. A discussion and assessment of the application of RFI mitigation techniques is presented for each type of radiometer.Peer ReviewedPostprint (published version

Performance assessment of time–frequency RFI mitigation techniques in microwave radiometry

©2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.Radio–frequency interference (RFI) signals are a well-known threat for microwave radiometry (MWR) applications. In order to alleviate this problem, different approaches for RFI detection and mitigation are currently under development. Since RFI signals are man made, they tend to have their power more concentrated in the time–frequency (TF) space as compared to naturally emitted noise. The aim of this paper is to perform an assessment of different TF RFI mitigation techniques in terms of probability of detection, resolution loss (RL), and mitigation performance. In this assessment, six different kinds of RFI signals have been considered: a glitch, a burst of pulses, a wide-band chirp, a narrow-band chirp, a continuous wave, and a wide-band modulation. The results show that the best performance occurs when the transform basis has a similar shape as compared to the RFI signal. For the best case performance, the maximum residual RFI temperature is 14.8 K, and the worst RL is 8.4%. Moreover, the multiresolution Fourier transform technique appears as a good tradeoff solution among all other techniques since it can mitigate all RFI signals under evaluation with a maximum residual RFI temperature of 21 K, and a worst RL of 26.3%. Although the obtained results are still far from an acceptable bias Misplaced < 1 K for MWR applications, there is still work to do in a combined test using the information gathered simultaneously by all mitigation techniques, which could improve the overall performance of RFI mitigation.Peer ReviewedPostprint (author's final draft

A pre-correlation RFI mitigation algorithm for L-band interferometric radiometers

Radio Frequency Interference (RFI) is a major concern for both real and synthetic aperture radiometers. After the lessons learnt from SMOS, ESA is preparing the next generation of L-band interferometric radiometers with RFI mitigation integrated into the cross-correlators. This work presents a preliminary design and results of a pre-correlation RFI mitigation algorithm tailored for interferometric radiometers. The results show that the correlation error introduced by the RFI is reduced on average to the half, with peaks of 20 dB of mitigation.Peer ReviewedPostprint (author's final draft

On the potential of empirical mode decomposition for RFI mitigation in microwave radiometry

Radio-frequency interference (RFI) is an increasing problem particularly for Earth observation using microwave radiometry. RFI has been observed, for example, at L-band by the European Space Agency’s (ESA’s) soil moisture and ocean salinity (SMOS) Earth Explorer and by National Aeronautics and Space Administration’s (NASA’s) soil moisture active passive (SMAP) and Aquarius missions, as well as at C-band by Advanced Microwave Scanning Radiometer (AMSR)-E and AMSR-2, and at 10.7 and 18.7 GHz by AMSR-E, AMSR-2, WindSat, and GPM Microwave Imager (GMI). Therefore, systems dedicated to interference detection and removal of contaminated measurements are nowadays a must in order to improve radiometric accuracy and reduce the loss of spatial coverage caused by interference. In this work, the feasibility of using the empirical mode decomposition (EMD) technique for RFI mitigation is explored. The EMD, also known as Hilbert–Huang transform (HHT), is an algorithm that decomposes the signal into intrinsic mode functions (IMFs). The achieved performance is analyzed, and the opportunities and caveats that this type of methods present are described. EMD is found to be a practical RFI mitigation method, albeit presenting some limitations and considerable complexity. Nevertheless, in some conditions, EMD exhibits a better performance than other commonly used methods (such as frequency binning). In particular, it has been found that EMD performs well for RFI affecting the <25% lower part of the intermediate frequency (IF) bandwidth.This work was supported in part by the Sensing With Pioneering Opportunistic Techniques (SPOT) under Grant RTI2018-099008-B-C21/ AEI/10.13039/501100011033, in part by the RYC-2016-20918 under Grant MCIN/AEI/10.13039/501100011033, and in part by the European Social Fund (ESF), Investing in your future.Peer ReviewedPostprint (author's final draft

MERITXELL: the Multifrequency Experimental Radiometer with Interference Tracking for Experiments over Land and Littoral—instrument description, calibration and performance

MERITXELL is a ground-based multisensor instrument that includes a multiband dual-polarization radiometer, a GNSS reflectometer, and several optical sensors. Its main goals are twofold: to test data fusion techniques, and to develop Radio-Frequency Interference (RFI) detection, localization and mitigation techniques. The former is necessary to retrieve complementary data useful to develop geophysical models with improved accuracy, whereas the latter aims at solving one of the most important problems of microwave radiometry. This paper describes the hardware design, the instrument control architecture, the calibration of the radiometer, and several captures of RFI signals taken with MERITXELL in urban environment. The multiband radiometer has a dual linear polarization total-power radiometer topology, and it covers the L-, S-, C-, X-, K-, Ka-, and W-band. Its back-end stage is based on a spectrum analyzer structure which allows to perform real-time signal processing, while the rest of the sensors are controlled by a host computer where the off-line processing takes place. The calibration of the radiometer is performed using the hot-cold load procedure, together with the tipping curves technique in the case of the five upper frequency bands. Finally, some captures of RFI signals are shown for most of the radiometric bands under analysis, which evidence the problem of RFI in microwave radiometry, and the limitations they impose in external calibration.Peer ReviewedPostprint (published version

Characteristics of the Global Radio Frequency Interference in the Protected Portion of L-Band

The National Aeronautics and Space Administration’s (NASA’s) Soil Moisture Active–Passive (SMAP) radiometer has been providing geolocated power moments measured within a 24 MHz band in the protected portion of L-band, i.e., 1400–1424 MHz, with 1.2 ms and 1.5 MHz time and frequency resolutions, as its Level 1A data. This paper presents important spectral and temporal properties of the radio frequency interference (RFI) in the protected portion of L-band using SMAP Level 1A data. Maximum and average bandwidth and duration of RFI signals, average RFI-free spectrum availability, and variations in such properties between ascending and descending satellite orbits have been reported across the world. The average bandwidth and duration of individual RFI sources have been found to be usually less than 4.5 MHz and 4.8 ms; and the average RFI-free spectrum is larger than 20 MHz in most regions with exceptions over the Middle East and Central and Eastern Asia. It has also been shown that, the bandwidth and duration of RFI signals can vary as much as 10 MHz and 10 ms, respectively, between ascending and descending orbits over certain locations. Furthermore, to identify frequencies susceptible to RFI contamination in the protected portion of L-band, observed RFI signals have been assigned to individual 1.5 MHz SMAP channels according to their frequencies. It has been demonstrated that, contrary to common perception, the center of the protected portion can be as RFI contaminated as its edges. Finally, there have been no significant correlations noted among different RFI properties such as amplitude, bandwidth, and duration within the 1400–1424 MHz ban

Impact of signal quantization on the performance of RFI mitigation algorithms

Radio Frequency Interference (RFI) is currently a major problem in Communications and Earth Observation, but it is even more dramatic in Microwave Radiometry because of the low power levels of the received signals. Its impact has been attested in several Earth Observation missions. On-board mitigation systems are becoming a requirement to detect and remove affected measurements, increasing thus radiometric accuracy and spatial coverage. However, RFI mitigation methods have not been tested yet in the context of some particular radiometer topologies, which rely on the use of coarsely quantized streams of data. In this study, the impact of quantization and sampling in the performance of several known RFI mitigation algorithms is studied under different conditions. It will be demonstrated that in the presence of clipping, quantization changes fundamentally the time-frequency properties of the contaminated signal, strongly impairing the performance of most mitigation methods. Important design considerations are derived from this analysis that must be taken into account when defining the architecture of future instruments. In particular, the use of Automatic Gain Control (AGC) systems is proposed, and its limitations are discussedPeer ReviewedPostprint (published version

Real-Time Detection and Filtering of Radio Frequency Interference On-board a Spaceborne Microwave Radiometer: The CubeRRT Mission

The Cubesat Radiometer Radio frequency interference Technology validation mission (CubeRRT) was developed to demonstrate real-time on-board detection and filtering of radio frequency interference (RFI) for wide bandwidth microwave radiometers. CubeRRT’s key technology is its radiometer digital backend (RDB) that is capable of measuring an instantaneous bandwidth of 1 GHz and of filtering the input signal into an estimated total power with and without RFI contributions. CubeRRT’s on-board RFI processing capability dramatically reduces the volume of data that must be downlinked to the ground and eliminates the need for ground-based RFI processing. RFI detection is performed by resolving the input bandwidth into 128 frequency sub-channels, with the kurtosis of each sub-channel and the variations in power across frequency used to detect non-thermal contributions. RFI filtering is performed by removing corrupted frequency sub-channels prior to the computation of the total channel power. The 1 GHz bandwidth input signals processed by the RDB are obtained from the payload’s antenna (ANT) and radiometer front end (RFE) subsystems that are capable of tuning across RF center frequencies from 6 to 40 GHz. The CubeRRT payload was installed into a 6U spacecraft bus provided by Blue Canyon Technologies that provides spacecraft power, communications, data management, and navigation functions. The design, development, integration and test, and on-orbit operations of CubeRRT are described in this paper. The spacecraft was delivered on March 22nd, 2018 for launch to the International Space Station (ISS) on May 21st, 2018. Since its deployment from the ISS on July 13th, 2018, the CubeRRT RDB has completed more than 5000 hours of operation successfully, validating its robustness as an RFI processor. Although CubeRRT’s RFE subsystem ceased operating on September 8th, 2018, causing the RDB input thereafter to consist only of internally generated noise, CubeRRT’s key RDB technology continues to operate without issue and has demonstrated its capabilities as a valuable subsystem for future radiometry missions

Radio frequency interference in microwave radiometry: statistical analysis and study of techniques for detection and mitigation

Microwave radiometry field has been increasing its performance with higher accuracy measurements, leading to a more presence in the remote sensing field. Several space-borne, air-borne and ground-based radiometers have been developed to perform measurement campaigns; however, the actual sensitivity of a radiometer is often limited by man-made radio emissions such as radars, broadcasting emissions, wireless communications and many other communication systems based on electromagnetic waves, limiting the improvement in the radiometers¿ performance. Consequently, in order to maintain the accuracy in the radiometric measurements, it has been researched in the Radio Frequency Interference (RFI) detection and mitigation systems and algorithms for the microwave radiometry field. The scope of this doctoral thesis is the development and testing of RFI detection and mitigation algorithms in order to enhance radiometric measurements performed by the Multifequency Experimental Radiometer with Interference Tracking for Experiments over Land and Littoral (MERITXELL). The MERITXELL has been developed during this thesis with the idea studying the RFI present in several radiometric bands and the way to mitigate it, as well as to obtain data from diverse frequency bands and devices in only one measurement campaign