Kinematic calibration of Orthoglide-type mechanisms from observation of parallel leg motions

The paper proposes a new calibration method for parallel manipulators that allows efficient identification of the joint offsets using observations of the manipulator leg parallelism with respect to the base surface. The method employs a simple and low-cost measuring system, which evaluates deviation of the leg location during motions that are assumed to preserve the leg parallelism for the nominal values of the manipulator parameters. Using the measured deviations, the developed algorithm estimates the joint offsets that are treated as the most essential parameters to be identified. The validity of the proposed calibration method and efficiency of the developed numerical algorithms are confirmed by experimental results. The sensitivity of the measurement methods and the calibration accuracy are also studied

An Overview of Kinematic and Calibration Models Using Internal/External Sensors or Constraints to Improve the Behavior of Spatial Parallel Mechanisms

This paper presents an overview of the literature on kinematic and calibration models of parallel mechanisms, the influence of sensors in the mechanism accuracy and parallel mechanisms used as sensors. The most relevant classifications to obtain and solve kinematic models and to identify geometric and non-geometric parameters in the calibration of parallel robots are discussed, examining the advantages and disadvantages of each method, presenting new trends and identifying unsolved problems. This overview tries to answer and show the solutions developed by the most up-to-date research to some of the most frequent questions that appear in the modelling of a parallel mechanism, such as how to measure, the number of sensors and necessary configurations, the type and influence of errors or the number of necessary parameters

The Design and Implementation of a Bayesian CAD Modeler for Robotic Applications

We present a Bayesian CAD modeler for robotic applications. We address the problem of taking into account the propagation of geometric uncertainties when solving inverse geometric problems. The proposed method may be seen as a generalization of constraint-based approaches in which we explicitly model geometric uncertainties. Using our methodology, a geometric constraint is expressed as a probability distribution on the system parameters and the sensor measurements, instead of a simple equality or inequality. To solve geometric problems in this framework, we propose an original resolution method able to adapt to problem complexity. Using two examples, we show how to apply our approach by providing simulation results using our modeler

Wing and body motion during flight initiation in Drosophila revealed by automated visual tracking

The fruit fly Drosophila melanogaster is a widely used model organism in studies of genetics, developmental biology and biomechanics. One limitation for exploiting Drosophila as a model system for behavioral neurobiology is that measuring body kinematics during behavior is labor intensive and subjective. In order to quantify flight kinematics during different types of maneuvers, we have developed a visual tracking system that estimates the posture of the fly from multiple calibrated cameras. An accurate geometric fly model is designed using unit quaternions to capture complex body and wing rotations, which are automatically fitted to the images in each time frame. Our approach works across a range of flight behaviors, while also being robust to common environmental clutter. The tracking system is used in this paper to compare wing and body motion during both voluntary and escape take-offs. Using our automated algorithms, we are able to measure stroke amplitude, geometric angle of attack and other parameters important to a mechanistic understanding of flapping flight. When compared with manual tracking methods, the algorithm estimates body position within 4.4±1.3% of the body length, while body orientation is measured within 6.5±1.9 deg. (roll), 3.2±1.3 deg. (pitch) and 3.4±1.6 deg. (yaw) on average across six videos. Similarly, stroke amplitude and deviation are estimated within 3.3 deg. and 2.1 deg., while angle of attack is typically measured within 8.8 deg. comparing against a human digitizer. Using our automated tracker, we analyzed a total of eight voluntary and two escape take-offs. These sequences show that Drosophila melanogaster do not utilize clap and fling during take-off and are able to modify their wing kinematics from one wingstroke to the next. Our approach should enable biomechanists and ethologists to process much larger datasets than possible at present and, therefore, accelerate insight into the mechanisms of free-flight maneuvers of flying insects

Education Software for the Modelling and Calibration of Kinematic Mechanisms

AbstractThis paper presents a new software for teaching the most important aspects of modelling, characterization and calibration of parallel mechanisms by means of the kinematic model, the kinematic parameter identification and the control of the system actuators and sensors. This application allows the student to develop competencies such as analysis and synthesis, to solve problems, research skills and to apply their knowledge.The developed tool presents a special interest in areas such as education, industry and research, since the application interface allows the user to carry out the different steps of the calibration procedure in an easy way. Besides, only one application is necessary to perform all the procedure for data acquisition and kinematic parameter identification.Moreover, thanks to the flexibility that the developed software offers in the programming, a senior undergraduate student can modify different algorithm variables and analyze the effects that take place with these changes. This application therefore presents an important utility as a teaching tool for the learning process and analysis of the different steps in the parallel mechanism optimization

Postprocesamiento CAM-ROBOTICA orientado al prototipado y mecanizado en células robotizadas complejas

The main interest of this thesis consists of the study and implementation of postprocessors to adapt the toolpath generated by a Computer Aided Manufacturing (CAM) system to a complex robotic workcell of eight joints, devoted to the rapid prototyping of 3D CAD-defined products. It consists of a 6R industrial manipulator mounted on a linear track and synchronized with a rotary table. To accomplish this main objective, previous work is required. Each task carried out entails a methodology, objective and partial results that complement each other, namely: - It is described the architecture of the workcell in depth, at both displacement and joint-rate levels, for both direct and inverse resolutions. The conditioning of the Jacobian matrix is described as kinetostatic performance index to evaluate the vicinity to singular postures. These ones are analysed from a geometric point of view. - Prior to any machining, the additional external joints require a calibration done in situ, usually in an industrial environment. A novel Non-contact Planar Constraint Calibration method is developed to estimate the external joints configuration parameters by means of a laser displacement sensor. - A first control is originally done by means of a fuzzy inference engine at the displacement level, which is integrated within the postprocessor of the CAM software. - Several Redundancy Resolution Schemes (RRS) at the joint-rate level are compared for the configuration of the postprocessor, dealing not only with the additional joints (intrinsic redundancy) but also with the redundancy due to the symmetry on the milling tool (functional redundancy). - The use of these schemes is optimized by adjusting two performance criterion vectors related to both singularity avoidance and maintenance of a preferred reference posture, as secondary tasks to be done during the path tracking. Two innovative fuzzy inference engines actively adjust the weight of each joint in these tasks.Andrés De La Esperanza, FJ. (2011). Postprocesamiento CAM-ROBOTICA orientado al prototipado y mecanizado en células robotizadas complejas [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/10627Palanci