Fixed and reconfigurable multiband antennas

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel UniversityWith the current scenario of development of antennas in the wireless communication field, the need of compact multiband, multifunctional and cost effective antenna is on the rise. The objective of this thesis is to present fixed and reconfigurable techniques and methods for small and slim multiband antennas, which are applicable to serve modern small and slime wireless, mobile and cognitive radio applications. In the fixed designs, independent control of the operating frequencies is investigated to enhance the antennas capabilities and to give the designer an additional level of freedom to design the antenna for other bands easily without altering the shape or the size of the antenna. In addition, for mobile phone antenna, the effect of user’s hand and mobile phone housing are studied to be with minimum effect. Although fixed multiband antennas can widely be used in many different systems or devices, they lack flexibility to accommodate new services compared with reconfigurable antennas. A reconfigurable antenna can be considered as one of the key advances for future wireless communication transceivers. The advantage of using a reconfigurable antenna is to operate in multiband where the total antenna volume can be reused and therefore the overall size can be reduced. Moreover, the future of cell phones and other personal mobile devices require compact multiband antennas and smart antennas with reconfigurable features. Two different types of frequency reconfigurability are investigated in this thesis: switchable and tunable. In the switchable reconfigurability, PIN diodes have been used so the antenna’s operating frequencies can hop between different services whereas varactor diode with variable capacitance allow the antenna’s operating frequencies to be fine-tuned over the operating bands. With this in mind, firstly, a switchable compact and slim antenna with two patch elements is presented for cognitive radio applications where the antenna is capable of operating in wideband and narrow bands depending on the states of the switches. In addition to this, a switchable design is proposed to switch between single, dual and tri bands applications (using a single varactor diode to act as a switch at lower capacitance values) with some fine tuning capabilities for the first and third bands when the capacitance of the diode is further increased. Secondly, the earlier designed fixed antennas are modified to be reconfigurable with fine-tuning so that they can be used for more applications in both wireless and mobile applications with the ability to control the bands simultaneously or independently over a wide range. Both analytical and numerical methods are used to implement a realistic and functional design. Parametric analyses using simulation tools are performed to study critical parameters that may affect the designs. Finally, the simulated designs are fabricated, and measured results are presented that validate the design approaches

Analysis and design of antennas for wireless communications using modal methods

El diseño de antenas para los nuevos sistemas de comunicaciones inalámbricas ha suscitado un creciente interés en los últimos años. El principal objetivo de esta Tesis Doctoral es la propuesta de un método general de diseño de antenas para sistemas de comunicaciones inalámbricas que proporcione una visión física del proceso de diseño. Para alcanzar este objetivo, se propone el uso de un método basado en la descomposición modal de la corriente en la superficie del cuerpo conductor. Los modos tienen la ventaja de proporcionar una visión más física del comportamiento radiante de la antena, así como información muy útil para la optimización de la geometría de la antena y para la selección del mecanismo óptimo de alimentación y su localización. En la Tesis se realizará una revisión de los diferentes métodos modales disponibles, así como de los parámetros más importantes a tratar cuando se trabaja con soluciones modales. Además, se investigará un método para obtener expresiones cerradas para las corrientes superficiales en objetos conductores planos abiertos. Como se verá, los objetos planos con formas canónicas se pueden interpretar en muchas ocasiones como deformaciones de objetos tridimensionales cuyas superficies coinciden con las de algunos de los sistemas de coordenadas curvilíneas. De esta forma, se obtendrán expresiones cerradas para los modos vectoriales en un disco conductor circular y una tira plana infinita. Estas funciones se propondrán como funciones base de dominio completo en problemas más complejos que incluyan este tipo de superficies planas. Los modos de corriente definidos a partir de las funciones de onda vectoriales son de naturaleza compleja, lo que dificulta en ocasiones su uso para el diseño de antenas. Por el contrario, la Teoría de los Modos Característicos proporciona una descomposición de la corriente total en la superficie de un cuerpo conductor de forma arbitraria en un conjunto de modos reales, cuyos diagramas de radiación son ortogonalesAntonino Daviu, E. (2008). Analysis and design of antennas for wireless communications using modal methods [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/2188Palanci

The Design of Novel Pattern Reconfigurable Antennas for Mobile Networks

This research evaluates a beam reconfigurable basestation transceiver for cellular applications from both a systems and antenna design perspective. The novelty in this research is the investigation of an automatic azimuth beamwidth switching antenna, which can effectively respond to homogeneous traffic distribution in a cellular mobile network. The proposed technique which this antenna uses is azimuth beam switching which incorporates PIN diodes to provide a reconfigurable reflecting ground plane for a three sector antenna. Numerical systems analysis has been carried out on a hexagonal homogeneous cellular network to evaluate how this reconfigurable antenna can balance mean and cell edge capacity through azimuth beamwidth reconfiguration. The optimum azimuth beamwidth is identified as 60°, which achieves the best cell capacity, and by reconfiguring the azimuth beamwidth from 60° to 110°, the maximized capacity at the edges of the cell can be improved. The influence of mechanical tilt, inter site distance, path loss model and vicinity of the cell edge for this antenna are described. This research shows that a mean cell edge improvement from 15Mbit/s to 18Mbit/s is achievable when beamwidth reconfiguration is used, and that this improvement is consistent for cell sizes from 500m to 1500m. Results from a test of an as-manufactured reconfigurable antenna are presented here, and show similar results compared to simulations. To overcome network coverage deterioration at large antenna downtilt angles in a homogeneous cellular mobile network, different beam shaping techniques in the elevation plane, including antenna sidelobe suppressing and null filling, are discussed here. By filling up the first upper-side null for a 12-element antenna array, both the average cell edge and cell capacity can be improved. The application of this beam shaping pattern for a 12-element array is described here, for the purpose of optimising a specific cell within a mobile network which is shown below average coverage and/or capacity. By choosing a proper antenna downtilt angle for this specific cell, whilst keeping the optimum tilt angle for other cells in the network, the cell’s coverage/capacity can be increased without impacting too much on the performance of other surrounding cells. Lastly, the effects of number of antenna elements for a 60° azimuth beamwidth antenna array on the network coverage/capacity are discussed here. This research shows that, as a result of an increasing number of antenna elements in an elevation direction, network capacity can be increased along with the optimum tilt angle. This suggests that a high gain antenna array in a cellular mobile network can be potential for large site deployment and fewer installations

Sensor Characteristics Reference Guide

The Buildings Technologies Office (BTO), within the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), is initiating a new program in Sensor and Controls. The vision of this program is: • Buildings operating automatically and continuously at peak energy efficiency over their lifetimes and interoperating effectively with the electric power grid. • Buildings that are self-configuring, self-commissioning, self-learning, self-diagnosing, self-healing, and self-transacting to enable continuous peak performance. • Lower overall building operating costs and higher asset valuation. The overarching goal is to capture 30% energy savings by enhanced management of energy consuming assets and systems through development of cost-effective sensors and controls. One step in achieving this vision is the publication of this Sensor Characteristics Reference Guide. The purpose of the guide is to inform building owners and operators of the current status, capabilities, and limitations of sensor technologies. It is hoped that this guide will aid in the design and procurement process and result in successful implementation of building sensor and control systems. DOE will also use this guide to identify research priorities, develop future specifications for potential market adoption, and provide market clarity through unbiased informatio

Development of piezoresistive sensors for biomedical applications

Tese de doutoramento em Engenharia Electrónica Industrial e de ComputadoresIn the last decades there has been an increase in sensing systems applied in a variety of situations with a large variety of sensor ranges. This represents a growing area with high potential. One of the areas of sensor development that require a great deal of attention is the area of sensor for biomedical applications and biosensors. These sensors have to overcome a number of challenges and limitations inherent to the environment where they are introduced. These difficulties lead to the necessity of using new materials and new techniques for their construction together with the more traditional materials, e.g. silicon based, which have already proven their potential in this area. Among the various materials, polymers have proven to be a good choice, due to a set of advantages such as simple processing, flexibility and facility of being obtained in different shapes. Therefore it is interesting to fabricate polymer based piezoresistive sensors for functional coatings of implantable hip prosthesis. These sensors will allow coating the prosthesis and provide new functionalities to the implants such as the possibility to measure forces and deformations between the prosthesis and the bone and therefore improving the postoperative diagnostic. In this works, a model of hip prosthesis with coated sensors was developed. For this purpose, flexible piezoresistive sensors have been developed that allow being implanted. Strain sensors were fabricated based on thin films of n+-nc-si.H by the technique of hot-wire chemical vapor deposition at a temperature of 150 ºC on a polymeric substrate, using the lithographic technique to construct the various layers of the sensors. The sensor has a gauge factor of -28 for low frequency deformation cycles. In the last decades there has been an increase in sensing systems applied in a variety of situations with a large variety of sensor ranges. This represents a growing area with high potential. One of the areas of sensor development that require a great deal of attention is the area of sensor for biomedical applications and biosensors. These sensors have to overcome a number of challenges and limitations inherent to the environment where they are introduced. These difficulties lead to the necessity of using new materials and new techniques for their construction together with the more traditional materials, e.g. silicon based, which have already proven their potential in this area. Among the various materials, polymers have proven to be a good choice, due to a set of advantages such as simple processing, flexibility and facility of being obtained in different shapes. Therefore it is interesting to fabricate polymer based piezoresistive sensors for functional coatings of implantable hip prosthesis. These sensors will allow coating the prosthesis and provide new functionalities to the implants such as the possibility to measure forces and deformations between the prosthesis and the bone and therefore improving the postoperative diagnostic. In this works, a model of hip prosthesis with coated sensors was developed. For this purpose, flexible piezoresistive sensors have been developed that allow being implanted. Strain sensors were fabricated based on thin films of n+-nc-si.H by the technique of hot-wire chemical vapor deposition at a temperature of 150 ºC on a polymeric substrate, using the lithographic technique to construct the various layers of the sensors. The sensor has a gauge factor of -28 for low frequency deformation cycles.In the last decades there has been an increase in sensing systems applied in a variety of situations with a large variety of sensor ranges. This represents a growing area with high potential. One of the areas of sensor development that require a great deal of attention is the area of sensor for biomedical applications and biosensors. These sensors have to overcome a number of challenges and limitations inherent to the environment where they are introduced. These difficulties lead to the necessity of using new materials and new techniques for their construction together with the more traditional materials, e.g. silicon based, which have already proven their potential in this area. Among the various materials, polymers have proven to be a good choice, due to a set of advantages such as simple processing, flexibility and facility of being obtained in different shapes. Therefore it is interesting to fabricate polymer based piezoresistive sensors for functional coatings of implantable hip prosthesis. These sensors will allow coating the prosthesis and provide new functionalities to the implants such as the possibility to measure forces and deformations between the prosthesis and the bone and therefore improving the postoperative diagnostic. In this works, a model of hip prosthesis with coated sensors was developed. For this purpose, flexible piezoresistive sensors have been developed that allow being implanted. Strain sensors were fabricated based on thin films of n+-nc-si.H by the technique of hot-wire chemical vapor deposition at a temperature of 150 ºC on a polymeric substrate, using the lithographic technique to construct the various layers of the sensors. The sensor has a gauge factor of -28 for low frequency deformation cycles. Sensors with larger flexibility were also developed though inkjet printing technique. Various configurations and materials were used to evaluate which materials are most appropriate for these types of sensors. Sensors with a gauge factor of approximately 2.5 for an active layer of PeDOT were obtained. A sensor matrix of 4 x 5 sensors was fabricated with an active area of 1.8 x 1.5 mm2 per sensor. These sensors were subjected to a set of electromechanical tests to evaluate its performance in situations close to end use. So the prosthesis was coated with the various sensors, cemented and subjected to deformation cycles for three levels of force according to standard ISO7206. An adaptive system read-out electronic circuit was developed and built that allows reading piezoresistive sensors with different characteristics. This system allows measuring a matrix of 8x8 sensors, but can be scaled to a large number of sensors. The readable range of the system is between 50 Ω and 100 kΩ according to the needs of the sensors being implanted. The total area of the circuit is 135 mm2, according to the requirements of a circuit to be used in in-vivo applications. An energy management system was also implemented that allows to activate and deactivate parts of the circuit when they are not needed, reducing the energy consumption. The system was validated by measuring a matrix of sensors with different characteristics. Finally, simulations were performed in order to evaluate the best options for the development of a wireless communications system. Three possible operation frequency ranges were used for three types of standard antennas. The communication system was introduced into a model simulating the characteristics of the various layers that constitute the human body. These simulations allow evaluate the frequency range most appropriate for implantable devices, the most appropriate antenna and the best location within the body. So the frequency chosen for the implementation was 868 Mhz for a Inverted- F antenna (IFA). In conclusion, the key elements for the implementations of an instrumented hip prosthesis were development and validated. The developed and/or simulated elements, including sensors, circuits for reading and communication system can also be used in other applications due to characteristics.These simulations allow evaluate the frequency range most appropriate for implantable devices, the most appropriate antenna and the best location within the body. So the frequency chosen for the implementation was 868 Mhz for a Inverted- F antenna (IFA). In conclusion, the key elements for the implementations of an instrumented hip prosthesis were development and validated. The developed and/or simulated elements, including sensors, circuits for reading and communication system can also be used in other applications due to characteristics. Neste trabalho foi desenvolvido um modelo de prótese de anca com implementação de sensores. Para atingir esse objectivo, foram desenvolvidos sensores piezoresitivos flexíveis que permitam ser implantados. Assim foram fabricados sensores de deformação baseados em filmes finos de n+-nc-si.H pela técnica de hot-wire chemical vapor deposition a uma temperatura de 150ºC sobre um substrato polimérico. Recorreu-se a técnica de litografia para construir as várias camadas do sensor. Os sensores apresentam um gauge factor de -28, para ciclos de baixa frequência em testes de four-point-bending. Foram ainda desenvolvidos sensores com uma maior flexibilidade através da técnica de inkjet printing. Para esse desenvolvimento foram usadas várias configurações e materiais, para avaliar quais os materiais mais adequados para este tipo de sensores. Na caracterização destes sensores obteve-se um gauge factor de aproximadamente 2.5 para uma camada ativa de PeDOT. Com os melhores sensores obtidos foram construídas matrizes de 4 x 5 sensores que apresentam uma área ativa de 1.8 x 1.5mm2 por sensor. Estes sensores foram sujeitos a um conjunto de ensaios electromecânicos, para avaliar o seu desempenho em situações próximas da utilização final. Desta forma foi revestida uma prótese com os diferentes sensores, cimentada e sujeita a ciclos de deformação para três níveis de força, segundo a norma ISO7206. Foi desenvolvido e construído um sistema de leitura adaptável que permite medir sensores piezoresistivos com diferentes características entre eles. Este sistema permite medir uma matriz de 8x8 sensores, mas pode ser escalada para um número maior de sensores. A gama de leitura do sistema varia entre 50 Ω e 100 kΩ, de acordo com as necessidades dos sensores a serem implementados. A área total deste circuito é de 135 mm2, de acordo com as necessidades de um circuito a ser utilizado em aplicações in-vivo. Foi também implementado um sistema de gestão de energia que permite ativar e desativar partes do circuito quando estas não são necessárias, permitindo, desta forma, reduzir os consumos de energia. O sistema foi validado através da medição de uma matriz de sensores com diferentes características. foram realizadas simulações de forma a avaliar as melhores opções para o desenvolvimento do sistema de comunicação sem fios. Foram usadas três possíveis gamas de frequência de operação para três tipos de antenas standard. O sistema de comunicação foi introduzido num modelo simulando as características das várias camadas que constituem o corpo humano. Estas simulações permitem aferir a gama de frequências mais adequadas para os dispositivos implantáveis, a antena mais adequada e a sua melhor localização, pois foi verificado como as várias camadas que constituem o corpo humano influenciam a comunicação. Assim, a frequência escolhida para a implementação foi de 868 MHz e a antena foi a IFA. Em conclusão, os elementos principais para a implementação de uma prótese de anca instrumentada, foram desenvolvidos e validados. Os elementos desenvolvidos e/ou simulados, incluindo os sensores, circuitos de leitura e sistema de comunicação, poderão igualmente ser utilizados em outras aplicações devido às suas boas características

Micro/Nano Structures and Systems

Micro/Nano Structures and Systems: Analysis, Design, Manufacturing, and Reliability is a comprehensive guide that explores the various aspects of micro- and nanostructures and systems. From analysis and design to manufacturing and reliability, this reprint provides a thorough understanding of the latest methods and techniques used in the field. With an emphasis on modern computational and analytical methods and their integration with experimental techniques, this reprint is an invaluable resource for researchers and engineers working in the field of micro- and nanosystems, including micromachines, additive manufacturing at the microscale, micro/nano-electromechanical systems, and more. Written by leading experts in the field, this reprint offers a complete understanding of the physical and mechanical behavior of micro- and nanostructures, making it an essential reference for professionals in this field

Cooperative Radio Communications for Green Smart Environments

The demand for mobile connectivity is continuously increasing, and by 2020 Mobile and Wireless Communications will serve not only very dense populations of mobile phones and nomadic computers, but also the expected multiplicity of devices and sensors located in machines, vehicles, health systems and city infrastructures. Future Mobile Networks are then faced with many new scenarios and use cases, which will load the networks with different data traffic patterns, in new or shared spectrum bands, creating new specific requirements. This book addresses both the techniques to model, analyse and optimise the radio links and transmission systems in such scenarios, together with the most advanced radio access, resource management and mobile networking technologies. This text summarises the work performed by more than 500 researchers from more than 120 institutions in Europe, America and Asia, from both academia and industries, within the framework of the COST IC1004 Action on "Cooperative Radio Communications for Green and Smart Environments". The book will have appeal to graduates and researchers in the Radio Communications area, and also to engineers working in the Wireless industry. Topics discussed in this book include: • Radio waves propagation phenomena in diverse urban, indoor, vehicular and body environments• Measurements, characterization, and modelling of radio channels beyond 4G networks• Key issues in Vehicle (V2X) communication• Wireless Body Area Networks, including specific Radio Channel Models for WBANs• Energy efficiency and resource management enhancements in Radio Access Networks• Definitions and models for the virtualised and cloud RAN architectures• Advances on feasible indoor localization and tracking techniques• Recent findings and innovations in antenna systems for communications• Physical Layer Network Coding for next generation wireless systems• Methods and techniques for MIMO Over the Air (OTA) testin

Cooperative Radio Communications for Green Smart Environments

The demand for mobile connectivity is continuously increasing, and by 2020 Mobile and Wireless Communications will serve not only very dense populations of mobile phones and nomadic computers, but also the expected multiplicity of devices and sensors located in machines, vehicles, health systems and city infrastructures. Future Mobile Networks are then faced with many new scenarios and use cases, which will load the networks with different data traffic patterns, in new or shared spectrum bands, creating new specific requirements. This book addresses both the techniques to model, analyse and optimise the radio links and transmission systems in such scenarios, together with the most advanced radio access, resource management and mobile networking technologies. This text summarises the work performed by more than 500 researchers from more than 120 institutions in Europe, America and Asia, from both academia and industries, within the framework of the COST IC1004 Action on "Cooperative Radio Communications for Green and Smart Environments". The book will have appeal to graduates and researchers in the Radio Communications area, and also to engineers working in the Wireless industry. Topics discussed in this book include: • Radio waves propagation phenomena in diverse urban, indoor, vehicular and body environments• Measurements, characterization, and modelling of radio channels beyond 4G networks• Key issues in Vehicle (V2X) communication• Wireless Body Area Networks, including specific Radio Channel Models for WBANs• Energy efficiency and resource management enhancements in Radio Access Networks• Definitions and models for the virtualised and cloud RAN architectures• Advances on feasible indoor localization and tracking techniques• Recent findings and innovations in antenna systems for communications• Physical Layer Network Coding for next generation wireless systems• Methods and techniques for MIMO Over the Air (OTA) testin

Metamaterial

In-depth analysis of the theory, properties and description of the most potential technological applications of metamaterials for the realization of novel devices such as subwavelength lenses, invisibility cloaks, dipole and reflector antennas, high frequency telecommunications, new designs of bandpass filters, absorbers and concentrators of EM waves etc. In order to create a new devices it is necessary to know the main electrodynamical characteristics of metamaterial structures on the basis of which the device is supposed to be created. The electromagnetic wave scattering surfaces built with metamaterials are primarily based on the ability of metamaterials to control the surrounded electromagnetic fields by varying their permeability and permittivity characteristics. The book covers some solutions for microwave wavelength scales as well as exploitation of nanoscale EM wavelength such as visible specter using recent advances of nanotechnology, for instance in the field of nanowires, nanopolymers, carbon nanotubes and graphene. Metamaterial is suitable for scholars from extremely large scientific domain and therefore given to engineers, scientists, graduates and other interested professionals from photonics to nanoscience and from material science to antenna engineering as a comprehensive reference on this artificial materials of tomorrow

BRIX₂ - A Versatile Toolkit for Rapid Prototyping and Education in Ubiquitous Computing

Zehe S. BRIX₂ - A Versatile Toolkit for Rapid Prototyping and Education in Ubiquitous Computing. Bielefeld: Universität Bielefeld; 2018