Design of a tunable multi-band differential LC VCO using 0.35 mu m SiGe BiCMOS technology for multi-standard wireless communication systems

In this paper, an integrated 2.2-5.7GHz multi-band differential LC VCO for multi-standard wireless communication systems was designed utilizing 0.35 mu m SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post-layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3 V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78 GHz, 3.22-3.53 GHz, 3.48-3.91 GHz and 4.528-5.7 GHz) with a maximum bandwidth of 1.36 GHz and a minimum bandwidth of 300 MHz. The designed and simulated VCO can generate a differential output power between 0.992 and -6.087 dBm with an average power consumption of 44.21 mW including the buffers. The average second and third harmonics level were obtained as -37.21 and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment. Output power of the fundamental frequency changes between -6.087 and 0.992 dBm, depending on the bias conditions (operating bands). Based on the post-layout simulation results, the core VCO circuit draws a current between 2.4-6.3 mA and between 11.4 and 15.3 mA with the buffer circuit from 3.3 V supply. The circuit occupies an area of 1.477 mm(2) on Si substrate, including DC, digital and RF pads

Voltage controlled oscillator for mm-wave radio systems

Abstract. The advancement in silicon technology has accelerated the development of integrated millimeter-wave transceiver systems operating up to 100 GHz with sophisticated functionality at a reduced consumer cost. Due to the progress in the field of signal processing, frequency modulated continuous wave (FMCW) radar has become common in recent years. A high-performance local oscillator (LO) is required to generate reference signals utilized in these millimeter-wave radar transceivers. To accomplish this, novel design techniques in fundamental voltage controlled oscillators (VCO) are necessary to achieve low phase noise, wide frequency tuning range, and good power efficiency. Although integrated VCOs have been studied for decades, as we move higher in the radio frequency spectrum, there are new trade-offs in the performance parameters that require further characterization. The work described in this thesis aims to design a fully integrated fundamental VCO targeting to 150 GHz, i.e., D-Band. The purpose is to observe and analyze the design limitations at these high frequencies and their corresponding trade-offs during the design procedure. The topology selected for this study is the cross-coupled LC tank VCO. For the study, two design topologies were considered: a conventional cross-coupled LC tank VCO and an inductive divider cross-coupled LC tank VCO. The conventional LC tank VCO yields better performance in terms of phase noise and tuning range. It is observed that the VCO is highly sensitive to parasitic contributions by the transistors, and the layout interconnects, thus limiting the targeted frequency range. The dimensions of the LC tank and the transistors are selected carefully. Moreover, the VCO performance is limited by the low Q factor of the LC tank governed by the varactor that is degrading the phase noise performance and the tuning range, respectively. The output buffer loaded capacitance and the core power consumption of the VCO are optimized. The layout is drawn carefully with strategies to minimize the parasitic effects. Considering all the design challenges, a 126 GHz VCO with a tuning range of 3.9% is designed. It achieves FOMT (Figure-of-merit) of -172 dBc/Hz, and phase noise of -99.14 dBc/Hz at 10 MHz offset, Core power consumption is 8.9 mW from a 1.2 V supply. Just falling short of the targeted frequency, the design is suitable for FMCW radar applications for future technologies. The design was done using Silicon-on-Insulator (SOI) CMOS technology

Study Of Design For Reliability Of Rf And Analog Circuits

Due to continued device dimensions scaling, CMOS transistors in the nanometer regime have resulted in major reliability and variability challenges. Reliability issues such as channel hot electron injection, gate dielectric breakdown, and negative bias temperature instability (NBTI) need to be accounted for in the design of robust RF circuits. In addition, process variations in the nanoscale CMOS transistors are another major concern in today‟s circuits design. An adaptive gate-source biasing scheme to improve the RF circuit reliability is presented in this work. The adaptive method automatically adjusts the gate-source voltage to compensate the reduction in drain current subjected to various device reliability mechanisms. A class-AB RF power amplifier shows that the use of a source resistance makes the power-added efficiency robust against threshold voltage and mobility variations, while the use of a source inductance is more reliable for the input third-order intercept point. A RF power amplifier with adaptive gate biasing is proposed to improve the circuit device reliability degradation and process variation. The performances of the power amplifier with adaptive gate biasing are compared with those of the power amplifier without adaptive gate biasing technique. The adaptive gate biasing makes the power amplifier more resilient to process variations as well as the device aging such as mobility and threshold voltage degradation. Injection locked voltage-controlled oscillators (VCOs) have been examined. The VCOs are implemented using TSMC 0.18 µm mixed-signal CMOS technology. The injection locked oscillators have improved phase noise performance than free running oscillators. iv A differential Clapp-VCO has been designed and fabricated for the evaluation of hot electron reliability. The differential Clapp-VCO is formed using cross-coupled nMOS transistors, on-chip transformers/inductors, and voltage-controlled capacitors. The experimental data demonstrate that the hot carrier damage increases the oscillation frequency and degrades the phase noise of Clapp-VCO. A p-channel transistor only VCO has been designed for low phase noise. The simulation results show that the phase noise degrades after NBTI stress at elevated temperature. This is due to increased interface states after NBTI stress. The process variability has also been evaluated

A study of Radiation-Tolerant Voltage-Controlled Oscillators designs in 65 nm bulk and 28 nm FDSOI CMOS technologies

Phase-locked loop (PLL) systems are widely employed in integrated circuits for space analog devices and communications systems that operate in radiation environments, where significant perturbations, especially in terms of phase noise, can be generated due to radiation particles. Among all the blocks that form a PLL system, previous research suggests the voltage-controlled oscillator (VCO) is one of the most critical components in terms of radiation tolerance and electric performance. Ring oscillators (ROs) and LC-tank VCOs have been commonly employed in high-performance PLLs. Nevertheless, both structures have drawbacks including a limited tuning range, high sensitivity to phase noise, limited radiation tolerance, and large design areas. In order to fulfill these high-performance requirements, a current-model logic (CML) based RO-VCO is presented as a possible solution capable of reducing the limitations of the commonly used structures and exploiting their advantages. The proposed hybrid VCO model includes passive components in its design which are the key parameters that define oscillation frequency of this structure. This tunable oscillator has been designed and tested in 65nm Bulk and 28 nm Fully depleted silicon-on-insulator (FDSOI) CMOS technologies The 65nm testchip was designed to compare the behavior of the proposed CML VCO with a current-starved RO and a radiation hardened by design (RHBD) LC-tank VCO in terms of tuning range, phase noise, Single event effect (SEE) sensitivity and design area. Simulations were carried out by applying a double exponential current pulse into different sensitive nodes of the three VCOs. In addition, SEE tests were conducted using pulsed laser experiments. Simulation and test results show that a CML VCO can effectively overcome the limitations presented by a RO-VCO and LC-tank VCO, achieving a wide range of tuning, and low sensitivity to noise and SEEs without the need for a large cross-section. Further studies of the proposed CML VCO were done on 28nm FDSOI in order to reduce the leakage current and increase the switching speed. the same current-starved VCO and CML VCO were implemented on this testchip, and simulations were performed by injecting a double exponential current pulse energy into the previously defined sensitive nodes. The results show SEE sensitivity improvement without narrowing the tuning range or affecting the phase noise response

Design of CMOS LC voltage controlled oscillators

This work presents the design and implementation of CMOS LC voltage controlled oscillators. On-chip planar spiral inductors and PMOS inversion mode varactors were utilized to implement the resonator. Two voltage controlled oscillators (VCOs) were realized as a part of this work, one designed to operate at 1.1 GHz while the second at 1.8 GHz. Both VCOs were implemented in a scalable digital CMOS process, with the former in a 1.5 micron CMOS process and the latter in a 0.5 micron technology. A simulation based methodology was adopted to arrive at a simple pi model used to model the metal and substrate related losses responsible for deteriorating the integrated inductor\u27s performance. Geometry based optimization techniques were utilized to arrive at an inductor geometry that ensures reasonable quality factor. In addition to the core VCO structure a host of test structures have been incorporated in order to carry out two-port network measurements in the future. Such measurements should enable one to gain a greater insight into the integrated inductor and varactor\u27s performance

RF CMOS Oscillators for Modern Wireless Applications

While mobile phones enjoy the largest production volume ever of any consumer electronics products, the demands they place on radio-frequency (RF) transceivers are particularly aggressive, especially on integration with digital processors, low area, low power consumption, while being robust against process-voltage-temperature variations. Since mobile terminals inherently operate on batteries, their power budget is severely constrained. To keep up with the ever increasing data-rate, an ever-decreasing power per bit is required to maintain the battery lifetime. The RF oscillator is the second most power-hungry block of a wireless radio (after power amplifiers). Consequently, any power reduction in an RF oscillator will greatly benefit the overall power efficiency of the cellular transceiver. Moreover, the RF oscillators' purity limits the transceiver performance. The oscillator's phase noise results in power leakage into adjacent channels in a transmit mode and reciprocal mixing in a receive mode. On the other hand, the multi-standard and multi-band transceivers that are now trending demand wide tuning range oscillators. However, broadening the oscillator’s tuning range is usually at the expense of die area (cost) or phase noise. The main goal of this book is to bring forth the exciting and innovative RF oscillator structures that demonstrate better phase noise performance, lower cost, and higher power efficiency than currently achievable. Technical topics discussed in RF CMOS Oscillators for Modern Wireless Applications include: Design and analysis of low phase-noise class-F oscillators Analyze a technique to reduce 1/f noise up-conversion in the oscillators Design and analysis of low power/low voltage oscillators Wide tuning range oscillators Reliability study of RF oscillators in nanoscale CMO

Ultra low phase noise 19 GHz VCO design in bipolar technology

The thesis treats a design for an ultra low phase noise VCO for backhaul Gbit point-to-point communication 81-86 GHz. Two VCO-circuits have been designed for a frequency of 19 GHz with a tuning range of more than 10 % and a phase noise below -120 dBc/Hz at an offset frequency of 1 MHz. Both circuits use INFINEON's bipolar SiGe process offering high speed transistors, a high-Q varactor and a thick top metal level. One VCO circuit uses the varactor directly coupled to the integrated inductor requiring a tuning voltage up to 10 V. Although also comparable phase noise commercial products from HITTITE require such unconvenient high tuning voltages. A second version was implemented based on an integrated transformer and operating with a tuning voltage between 0 and 3.3 V. The power consumption of both implemented VCOs is 20 mA from a single 3.3 V supply voltag

Realization of a voltage controlled oscillator using 0.35 um sige-bicmos technology for multi-band applications

The stable growth in wireless communications market has engendered the interoperability of various standards in a single broadband frequency range from hundred MHz up to several GHz. This frequency range consists of various wireless applications such as GSM, Bluetooth and WLAN. Therefore, an agile wireless system needs smart RF front-ends for functioning properly in such a crowded spectrum. As a result, the demand for multi-standard RF transceivers which put various wireless and cordless phone standards together in one structure was increased. The demand for multi-standard RF transceivers gives a key role to reconfigurable wideband VCO operation with low-power and low-phase noise characteristics. Besides agility and intelligence, such a communication system (GSM, WLAN, Global Positioning Systems, etc. ) required meeting the requirements of several standards in a cost-effective way. This, when cost and integration are the major concerns, leads to the exploitation of Si-based technologies. In this thesis, an integrated 2.2-5.7GHz Multi-band differential LC VCO for Multi-standard Wireless Communication systems was designed utilizing 0.35μm SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78GHz, 3.22-3.53GHz, 3.48-3.91GHz and 4.528-5.7GHz) with a maximum bandwidth of 1.36GHz and a minimum bandwidth of 300MHz. The designed and simulated VCO can generate a differential output power between 0.992 dBm and -6.087 dBm with an average power consumption of 44.21mW including the buffers. The average second and third harmonics level were obtained as -37.21 dBm and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment

RF CMOS Oscillators for Modern Wireless Applications

While mobile phones enjoy the largest production volume ever of any consumer electronics products, the demands they place on radio-frequency (RF) transceivers are particularly aggressive, especially on integration with digital processors, low area, low power consumption, while being robust against process-voltage-temperature variations. Since mobile terminals inherently operate on batteries, their power budget is severely constrained. To keep up with the ever increasing data-rate, an ever-decreasing power per bit is required to maintain the battery lifetime. The RF oscillator is the second most power-hungry block of a wireless radio (after power amplifiers). Consequently, any power reduction in an RF oscillator will greatly benefit the overall power efficiency of the cellular transceiver. Moreover, the RF oscillators' purity limits the transceiver performance. The oscillator's phase noise results in power leakage into adjacent channels in a transmit mode and reciprocal mixing in a receive mode. On the other hand, the multi-standard and multi-band transceivers that are now trending demand wide tuning range oscillators. However, broadening the oscillator’s tuning range is usually at the expense of die area (cost) or phase noise. The main goal of this book is to bring forth the exciting and innovative RF oscillator structures that demonstrate better phase noise performance, lower cost, and higher power efficiency than currently achievable. Technical topics discussed in RF CMOS Oscillators for Modern Wireless Applications include: Design and analysis of low phase-noise class-F oscillators Analyze a technique to reduce 1/f noise up-conversion in the oscillators Design and analysis of low power/low voltage oscillators Wide tuning range oscillators Reliability study of RF oscillators in nanoscale CMO