A knowledge-based approach for the extraction of machining features from solid models

Computer understanding of machining features such as holes and pockets is essential for bridging the communication gap between Computer Aided Design and Computer Aided Manufacture. This thesis describes a prototype machining feature extraction system that is implemented by integrating the VAX-OPS5 rule-based artificial intelligence environment with the PADL-2 solid modeller. Specification of original stock and finished part geometry within the solid modeller is followed by determination of the nominal surface boundary of the corresponding cavity volume model by means of Boolean subtraction and boundary evaluation. The boundary model of the cavity volume is managed by using winged-edge and frame-based data structures. Machining features are extracted using two methods : (1) automatic feature recognition, and (2) machine learning of features for subsequent recognition. [Continues.

Development Of Cutter Geometrical Feature For Machining Thin Wall Part

Demand for cost-effective aircrafts fabrication has motivated the aerospace industry to use nontraditional materials and new aircraft structural design. New aircrafts are designed with monolithic component to replace large number of assembled component. For manufacturers, high-performance cutting tool is essential as more than 80% of the material is removed to produce the monolithic component. Most of the monolithic components have thin-wall feature with low stiffness and deformation is more likely to occur in its machining process, resulting in dimensional surface errors. Most of the existing research on machining thin-wall component merely focused on the process planning and there was no scientific study on the effects of cutter geometric feature on component failure. Tool geometry has a direct influence on the cutting performance and should be taken into consideration. In this research, due to the importance of machining efficiency, development of new cutter design specifically for machining thin-wall components are studied. This study consists of both experimental and statistic techniques to evaluate the machining performance associated with the cutter geometry for different types of end mill, namely variable helix constant pitch (VHCP), variable helix variable pitch (VHVP) and tabular helix constant pitch (THCP). Based on the established relationship between cutter geometry feature and machining performances, the optimal cutter geometry is determined by using the non-parametric statistical ranking technique. From the experimental results, tool TD3 with 31o/33o/35o helix angle and equal pitch angle of 90o between teeth (THCP) is the most suitable design to be used for machining thin-wall workpiece. In addition, it shows that careful design of the pitch and helix angle combination can increase the machining performances of thin-wall part. The outcome from this research has potential benefits in providing new scientific knowledge on the selection of effective cutter geometry for machining low rigidity components

Topological model for machining of parts with complex shapes

Complex shapes are widely used to design products in several industries such as aeronautics, automotive and domestic appliances. Several variations of their curvatures and orientations generate difficulties during their manufacturing or the machining of dies used in moulding, injection and forging. Analysis of several parts highlights two levels of difficulties between three types of shapes: prismatic parts with simple geometrical shapes, aeronautic structure parts composed of several shallow pockets and forging dies composed of several deep cavities which often contain protrusions. This paper mainly concerns High Speed Machining (HSM) of these dies which represent the highest complexity level because of the shapes' geometry and their topology. Five axes HSM is generally required for such complex shaped parts but 3 axes machining can be sufficient for dies. Evolutions in HSM CAM software and machine tools lead to an important increase in time for machining preparation. Analysis stages of the CAD model particularly induce this time increase which is required for a wise choice of cutting tools and machining strategies. Assistance modules for prismatic parts machining features identification in CAD models are widely implemented in CAM software. In spite of the last CAM evolutions, these kinds of CAM modules are undeveloped for aeronautical structure parts and forging dies. Development of new CAM modules for the extraction of relevant machining areas as well as the definition of the topological relations between these areas must make it possible for the machining assistant to reduce the machining preparation time. In this paper, a model developed for the description of complex shape parts topology is presented. It is based on machining areas extracted for the construction of geometrical features starting from CAD models of the parts. As topology is described in order to assist machining assistant during machining process generation, the difficulties associated with tasks he carried out are analyzed at first. The topological model presented after is based on the basic geometrical features extracted. Topological relations which represent the framework of the model are defined between the basic geometrical features which are gathered afterwards in macro-features. Approach used for the identification of these macro-features is also presented in this paper. Detailed application on the construction of the topological model of forging dies is presented in the last part of the paper

Machining of complex-shaped parts with guidance curves

Nowadays, high-speed machining is usually used for production of hardened material parts with complex shapes such as dies and molds. In such parts, tool paths generated for bottom machining feature with the conventional parallel plane strategy induced many feed rate reductions, especially when boundaries of the feature have a lot of curvatures and are not parallel. Several machining experiments on hardened material lead to the conclusion that a tool path implying stable cutting conditions might guarantee a better part surface integrity. To ensure this stability, the shape machined must be decomposed when conventional strategies are not suitable. In this paper, an experimental approach based on high-speed performance simulation is conducted on a master bottom machining feature in order to highlight the influence of the curvatures towards a suitable decomposition of machining area. The decomposition is achieved through the construction of intermediate curves between the closed boundaries of the feature. These intermediate curves are used as guidance curve for the tool paths generation with an alternative machining strategy called "guidance curve strategy". For the construction of intermediate curves, key parameters reflecting the influence of their proximity with each closed boundary and the influence of the curvatures of this latter are introduced. Based on the results, a method for defining guidance curves in four steps is proposed

Implementing Rapid Prototyping Using CNC Machining (CNC-RP) Through a CAD/CAM Interface

This paper presents the methodology and implementation of a rapid machining system using a CAD/CAM interface. Rapid Prototyping using CNC Machining (CNC-RP) is a method that has been developed which enables automatic generation of process plans for a machined component. The challenge with CNC-RP is not the technical problems of material removal, but with all of the required setup, fixture and toolpath planning, which has previously required a skilled machinist. Through the use of advanced geometric algorithms, we have implemented an interface with a CAD/CAM system that allows true automatic NC code generation directly from a CAD model with no human interaction; a capability necessary for a practical rapid prototyping system.Mechanical Engineerin

Variation propagation of bench vises in multi-stage machining processes

Comunicación presentada a MESIC 2019 8th Manufacturing Engineering Society International Conference (Madrid, 19-21 de Junio de 2019)Variation propagation has been successfully modeled by the Stream of Variation (SoV) approach in multistage machining processes. However, the SoV model basically supports 3-2-1 fixtures based on punctual locators and other workholding systems such as conventional vises are not considered yet. In this paper, the SoV model is expanded to include the fixture- and datum-induced variations on workholding devices such as bench vises. The model derivation is validated through assembly and machining simulations on Computer Aided Design software. The case study analyzed shows an average error of part quality prediction between the SoV model and the CAD simulations of 0.26%

Feature recognition & tool path generation for 5 axis STEP-NC machining of free form / irregular contoured surfaces

This research paper presents a five step algorithm to generate tool paths for machining Free form / Irregular Contoured Surface(s) (FICS) by adopting STEP-NC (AP-238) format. In the first step, a parametrized CAD model with FICS is created or imported in UG-NX6.0 CAD package. The second step recognizes the features and calculates a Closeness Index (CI) by comparing them with the B-Splines / Bezier surfaces. The third step utilizes the CI and extracts the necessary data to formulate the blending functions for identified features. In the fourth step Z-level 5 axis tool paths are generated by adopting flat and ball end mill cutters. Finally, in the fifth step, tool paths are integrated with STEP-NC format and validated. All these steps are discussed and explained through a validated industrial component