Quiescent current testing of CMOS data converters

Power supply quiescent current (IDDQ) testing has been very effective in VLSI circuits designed in CMOS processes detecting physical defects such as open and shorts and bridging defects. However, in sub-micron VLSI circuits, IDDQ is masked by the increased subthreshold (leakage) current of MOSFETs affecting the efficiency of I¬DDQ testing. In this work, an attempt has been made to perform robust IDDQ testing in presence of increased leakage current by suitably modifying some of the test methods normally used in industry. Digital CMOS integrated circuits have been tested successfully using IDDQ and IDDQ methods for physical defects. However, testing of analog circuits is still a problem due to variation in design from one specific application to other. The increased leakage current further complicates not only the design but also testing. Mixed-signal integrated circuits such as the data converters are even more difficult to test because both analog and digital functions are built on the same substrate. We have re-examined both IDDQ and IDDQ methods of testing digital CMOS VLSI circuits and added features to minimize the influence of leakage current. We have designed built-in current sensors (BICS) for on-chip testing of analog and mixed-signal integrated circuits. We have also combined quiescent current testing with oscillation and transient current test techniques to map large number of manufacturing defects on a chip. In testing, we have used a simple method of injecting faults simulating manufacturing defects invented in our VLSI research group. We present design and testing of analog and mixed-signal integrated circuits with on-chip BICS such as an operational amplifier, 12-bit charge scaling architecture based digital-to-analog converter (DAC), 12-bit recycling architecture based analog-to-digital converter (ADC) and operational amplifier with floating gate inputs. The designed circuits are fabricated in 0.5 μm and 1.5 μm n-well CMOS processes and tested. Experimentally observed results of the fabricated devices are compared with simulations from SPICE using MOS level 3 and BSIM3.1 model parameters for 1.5 μm and 0.5 μm n-well CMOS technologies, respectively. We have also explored the possibility of using noise in VLSI circuits for testing defects and present the method we have developed

Investigation into voltage and process variation-aware manufacturing test

Increasing integration and complexity in IC design provides challenges for manufacturing testing. This thesis studies how process and supply voltage variation influence defect behaviour to determine the impact on manufacturing test cost and quality. The focus is on logic testing of static CMOS designs with respect to two important defect types in deep submicron CMOS: resistive bridges and full opens. The first part of the thesis addresses testing for resistive bridge defects in designs with multiple supply voltage settings. To enable analysis, a fault simulator is developed using a supply voltage-aware model for bridge defect behaviour. The analysis shows that for high defect coverage it is necessary to perform test for more than one supply voltage setting, due to supply voltage-dependent behaviour. A low-cost and effective test method is presented consisting of multi-voltage test generation that achieves high defect coverage and test set size reduction without compromise to defect coverage. Experiments on synthesised benchmarks with realistic bridge locations validate the proposed method.The second part focuses on the behaviour of full open defects under supply voltage variation. The aim is to determine the appropriate value of supply voltage to use when testing. Two models are considered for the behaviour of full open defects with and without gate tunnelling leakage influence. Analysis of the supply voltage-dependent behaviour of full open defects is performed to determine if it is required to test using more than one supply voltage to detect all full open defects. Experiments on synthesised benchmarks using an extended version of the fault simulator tool mentioned above, measure the quantitative impact of supply voltage variation on defect coverage.The final part studies the impact of process variation on the behaviour of bridge defects. Detailed analysis using synthesised ISCAS benchmarks and realistic bridge model shows that process variation leads to additional faults. If process variation is not considered in test generation, the test will fail to detect some of these faults, which leads to test escapes. A novel metric to quantify the impact of process variation on test quality is employed in the development of a new test generation tool, which achieves high bridge defect coverage. The method achieves a user-specified test quality with test sets which are smaller than test sets generated without consideration of process variation

The Fifth NASA Symposium on VLSI Design

The fifth annual NASA Symposium on VLSI Design had 13 sessions including Radiation Effects, Architectures, Mixed Signal, Design Techniques, Fault Testing, Synthesis, Signal Processing, and other Featured Presentations. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The presentations share insights into next generation advances that will serve as a basis for future VLSI design

Resilience of an embedded architecture using hardware redundancy

In the last decade the dominance of the general computing systems market has being replaced by embedded systems with billions of units manufactured every year. Embedded systems appear in contexts where continuous operation is of utmost importance and failure can be profound. Nowadays, radiation poses a serious threat to the reliable operation of safety-critical systems. Fault avoidance techniques, such as radiation hardening, have been commonly used in space applications. However, these components are expensive, lag behind commercial components with regards to performance and do not provide 100% fault elimination. Without fault tolerant mechanisms, many of these faults can become errors at the application or system level, which in turn, can result in catastrophic failures. In this work we study the concepts of fault tolerance and dependability and extend these concepts providing our own definition of resilience. We analyse the physics of radiation-induced faults, the damage mechanisms of particles and the process that leads to computing failures. We provide extensive taxonomies of 1) existing fault tolerant techniques and of 2) the effects of radiation in state-of-the-art electronics, analysing and comparing their characteristics. We propose a detailed model of faults and provide a classification of the different types of faults at various levels. We introduce an algorithm of fault tolerance and define the system states and actions necessary to implement it. We introduce novel hardware and system software techniques that provide a more efficient combination of reliability, performance and power consumption than existing techniques. We propose a new element of the system called syndrome that is the core of a resilient architecture whose software and hardware can adapt to reliable and unreliable environments. We implement a software simulator and disassembler and introduce a testing framework in combination with ERA’s assembler and commercial hardware simulators

Design of On-Chip Self-Testing Signature Register

Over the last few years, scan test has turn out to be too expensive to implement for industry standard designs due to increasing test data volume and test time. The test cost of a chip is mainly governed by the resource utilization of Automatic Test Equipment (ATE). Also, it directly depends upon test time that includes time required to load test program, to apply test vectors and to analyze generated test response of the chip. An issue of test time and data volume is increasingly appealing designers to use on-chip test data compactors, either on input side or output side or both. Such techniques significantly address the former issues but have little hold over increasing number of input-outputs under test mode. Further, test pins on DUT are increasing over the generations. Thus, scan channels on test floor are falling short in number for placement of such ICs. To address issues discussed above, we introduce an on-chip self-testing signature register. It comprises a response compactor and a comparator. The compactor compacts large chunk of response data to a small test signature whereas the comparator compares this test signature with desired one. The overall test result for the design is generated on single output pin. Being no storage of test response is demanded, the considerable reduction in ATE memory can be observed. Also, with only single pin to be monitored for test result, the number of tester channels and compare edges on ATE side significantly reduce at the end of the test. This cuts down maintenance and usage cost of test floor and increases its life time. Furthermore reduction in test pins gives scope for DFT engineers to increase number of scan chains so as to further reduce test time

Automatic test pattern generation for asynchronous circuits

The testability of integrated circuits becomes worse with transistor dimensions reaching nanometer scales. Testing, the process of ensuring that circuits are fabricated without defects, becomes inevitably part of the design process; a technique called design for test (DFT). Asynchronous circuits have a number of desirable properties making them suitable for the challenges posed by modern technologies, but are severely limited by the unavailability of EDA tools for DFT and automatic test-pattern generation (ATPG). This thesis is motivated towards developing test generation methodologies for asynchronous circuits. In total four methods were developed which are aimed at two different fault models: stuck-at faults at the basic logic gate level and transistor-level faults. The methods were evaluated using a set of benchmark circuits and compared favorably to previously published work. First, ABALLAST is a partial-scan DFT method adapting the well-known BALLAST technique for asynchronous circuits where balanced structures are used to guide the selection of the state-holding elements that will be scanned. The test inputs are automatically provided by a novel test pattern generator, which uses time frame unrolling to deal with the remaining, non-scanned sequential C-elements. The second method, called AGLOB, uses algorithms from strongly-connected components in graph graph theory as a method for finding the optimal position of breaking the loops in the asynchronous circuit and adding scan registers. The corresponding ATPG method converts cyclic circuits into acyclic for which standard tools can provide test patterns. These patterns are then automatically converted for use in the original cyclic circuits. The third method, ASCP, employs a new cycle enumeration method to find the loops present in a circuit. Enumerated cycles are then processed using an efficient set covering heuristic to select the scan elements for the circuit to be tested.Applying these methods to the benchmark circuits shows an improvement in fault coverage compared to previous work, which, for some circuits, was substantial. As no single method consistently outperforms the others in all benchmarks, they are all valuable as a designer’s suite of tools for testing. Moreover, since they are all scan-based, they are compatible and thus can be simultaneously used in different parts of a larger circuit. In the final method, ATRANTE, the main motivation of developing ATPG is supplemented by transistor level test generation. It is developed for asynchronous circuits designed using a State Transition Graph (STG) as their specification. The transistor-level circuit faults are efficiently mapped onto faults that modify the original STG. For each potential STG fault, the ATPG tool provides a sequence of test vectors that expose the difference in behavior to the output ports. The fault coverage obtained was 52-72 % higher than the coverage obtained using the gate level tests. Overall, four different design for test (DFT) methods for automatic test pattern generation (ATPG) for asynchronous circuits at both gate and transistor level were introduced in this thesis. A circuit extraction method for representing the asynchronous circuits at a higher level of abstraction was also implemented. Developing new methods for the test generation of asynchronous circuits in this thesis facilitates the test generation for asynchronous designs using the CAD tools available for testing the synchronous designs. Lessons learned and the research questions raised due to this work will impact the future work to probe the possibilities of developing robust CAD tools for testing the future asynchronous designs

The 1992 4th NASA SERC Symposium on VLSI Design

Papers from the fourth annual NASA Symposium on VLSI Design, co-sponsored by the IEEE, are presented. Each year this symposium is organized by the NASA Space Engineering Research Center (SERC) at the University of Idaho and is held in conjunction with a quarterly meeting of the NASA Data System Technology Working Group (DSTWG). One task of the DSTWG is to develop new electronic technologies that will meet next generation electronic data system needs. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The NASA SERC is proud to offer, at its fourth symposium on VLSI design, presentations by an outstanding set of individuals from national laboratories, the electronics industry, and universities. These speakers share insights into next generation advances that will serve as a basis for future VLSI design

Algorithms for Power Aware Testing of Nanometer Digital ICs

At-speed testing of deep-submicron digital very large scale integrated (VLSI) circuits has become mandatory to catch small delay defects. Now, due to continuous shrinking of complementary metal oxide semiconductor (CMOS) transistor feature size, power density grows geometrically with technology scaling. Additionally, power dissipation inside a digital circuit during the testing phase (for test vectors under all fault models (Potluri, 2015)) is several times higher than its power dissipation during the normal functional phase of operation. Due to this, the currents that flow in the power grid during the testing phase, are much higher than what the power grid is designed for (the functional phase of operation). As a result, during at-speed testing, the supply grid experiences unacceptable supply IR-drop, ultimately leading to delay failures during at-speed testing. Since these failures are specific to testing and do not occur during functional phase of operation of the chip, these failures are usually referred to false failures, and they reduce the yield of the chip, which is undesirable. In nanometer regime, process parameter variations has become a major problem. Due to the variation in signalling delays caused by these variations, it is important to perform at-speed testing even for stuck faults, to reduce the test escapes (McCluskey and Tseng, 2000; Vorisek et al., 2004). In this context, the problem of excessive peak power dissipation causing false failures, that was addressed previously in the context of at-speed transition fault testing (Saxena et al., 2003; Devanathan et al., 2007a,b,c), also becomes prominent in the context of at-speed testing of stuck faults (Maxwell et al., 1996; McCluskey and Tseng, 2000; Vorisek et al., 2004; Prabhu and Abraham, 2012; Potluri, 2015; Potluri et al., 2015). It is well known that excessive supply IR-drop during at-speed testing can be kept under control by minimizing switching activity during testing (Saxena et al., 2003). There is a rich collection of techniques proposed in the past for reduction of peak switching activity during at-speed testing of transition/delay faults ii in both combinational and sequential circuits. As far as at-speed testing of stuck faults are concerned, while there were some techniques proposed in the past for combinational circuits (Girard et al., 1998; Dabholkar et al., 1998), there are no techniques concerning the same for sequential circuits. This thesis addresses this open problem. We propose algorithms for minimization of peak switching activity during at-speed testing of stuck faults in sequential digital circuits under the combinational state preservation scan (CSP-scan) architecture (Potluri, 2015; Potluri et al., 2015). First, we show that, under this CSP-scan architecture, when the test set is completely specified, the peak switching activity during testing can be minimized by solving the Bottleneck Traveling Salesman Problem (BTSP). This mapping of peak test switching activity minimization problem to BTSP is novel, and proposed for the first time in the literature. Usually, as circuit size increases, the percentage of don’t cares in the test set increases. As a result, test vector ordering for any arbitrary filling of don’t care bits is insufficient for producing effective reduction in switching activity during testing of large circuits. Since don’t cares dominate the test sets for larger circuits, don’t care filling plays a crucial role in reducing switching activity during testing. Taking this into consideration, we propose an algorithm, XStat, which is capable of performing test vector ordering while preserving don’t care bits in the test vectors, following which, the don’t cares are filled in an intelligent fashion for minimizing input switching activity, which effectively minimizes switching activity inside the circuit (Girard et al., 1998). Through empirical validation on benchmark circuits, we show that XStat minimizes peak switching activity significantly, during testing. Although XStat is a very powerful heuristic for minimizing peak input-switchingactivity, it will not guarantee optimality. To address this issue, we propose an algorithm that uses Dynamic Programming to calculate the lower bound for a given sequence of test vectors, and subsequently uses a greedy strategy for filling don’t cares in this sequence to achieve this lower bound, thereby guaranteeing optimality. This algorithm, which we refer to as DP-fill in this thesis, provides the globally optimal solution for minimizing peak input-switching-activity and also is the best known in the literature for minimizing peak input-switching-activity during testing. The proof of optimality of DP-fill in minimizing peak input-switching-activity is also provided in this thesis

Développement des techniques de test et de diagnostic pour les FPGA hiérarchique de type mesh

The evolution trend of shrinking feature size and increasing complexity in modern electronics is being slowed down due to physical limits that generate numerous imperfections and defects during fabrication steps or projected life time of the chip. Field Programmable Gate Arrays (FPGAs) are used in complex digital systems mainly due to their reconfigurability and shorter time-to-market. To maintain a high reliability of such systems, FPGAs should be tested thoroughly for defects. FPGA architecture optimization for area saving and better signal routability is an ongoing process which directly impacts the overall FPGA testability, hence the reliability. This thesis presents a complete strategy for test and diagnosis of manufacturing defects in mesh-based FPGAs containing a novel multilevel interconnects topology which promises to provide better area and routability. Efficiency of the proposed test schemes is analyzed in terms of test cost, respective fault coverage and diagnostic resolution.L’évolution tendant à réduire la taille et augmenter la complexité des circuits électroniques modernes, est en train de ralentir du fait des limitations technologiques, qui génèrent beaucoup de d’imperfections et de defaults durant la fabrication ou la durée de vie de la puce. Les FPGAs sont utilisés dans les systèmes numériques complexes, essentiellement parce qu’ils sont reconfigurables et rapide à commercialiser. Pour garder une grande fiabilité de tels systèmes, les FPGAs doivent être testés minutieusement pour les defaults. L’optimisation de l’architecture des FPGAs pour l’économie de surface et une meilleure routabilité est un processus continue qui impacte directement la testabilité globale et de ce fait, la fiabilité. Cette thèse présente une stratégie complète pour le test et le diagnostique des defaults de fabrication des “mesh-based FPGA” contenant une nouvelle topologie d’interconnections à plusieurs niveaux, ce qui promet d’apporter une meilleure routabilité. Efficacité des schémas proposes est analysée en termes de temps de test, couverture de faute et résolution de diagnostique

Intelligent Circuits and Systems

ICICS-2020 is the third conference initiated by the School of Electronics and Electrical Engineering at Lovely Professional University that explored recent innovations of researchers working for the development of smart and green technologies in the fields of Energy, Electronics, Communications, Computers, and Control. ICICS provides innovators to identify new opportunities for the social and economic benefits of society.　 This conference bridges the gap between academics and R&D institutions, social visionaries, and experts from all strata of society to present their ongoing research activities and foster research relations between them. It provides opportunities for the exchange of new ideas, applications, and experiences in the field of smart technologies and finding global partners for future collaboration. The ICICS-2020 was conducted in two broad categories, Intelligent Circuits & Intelligent Systems and Emerging Technologies in Electrical Engineering