Hardware Specific Integration Strategy for Impedance-Based Structural Health Monitoring of Aerospace Systems

The Integrated Vehicle Health Management (IVHM) Project, sponsored by NASA's Aeronautics Research Mission Directorate, is conducting research to advance the state of highly integrated and complex flight-critical health management technologies and systems. An effective IVHM system requires Structural Health Monitoring (SHM). The impedance method is one such SHM technique for detection and monitoring complex structures for damage. This position paper on the impedance method presents the current state of the art, future directions, applications and possible flight test demonstrations

Perpetual Reconfigurable Intelligent Surfaces Through In-Band Energy Harvesting: Architectures, Protocols, and Challenges

Reconfigurable intelligent surfaces (RISs) are considered to be a key enabler of highly energy-efficient 6G and beyond networks. This property arises from the absence of power amplifiers in the structure, in contrast to active nodes, such as small cells and relays. However, still an amount of power is required for their operation. To improve their energy efficiency further, we propose the notion of perpetual RISs, which secure the power needed to supply their functionalities through wireless energy harvesting of the impinging transmitted electromagnetic signals. Towards this, we initially explain the rationale behind such RIS capability and proceed with the presentation of the main RIS controller architecture that can realize this vision under an in-band energy harvesting consideration. Furthermore, we present a typical energy-harvesting architecture followed by two harvesting protocols. Subsequently, we study the performance of the two protocols under a typical communications scenario. Finally, we elaborate on the main research challenges governing the realization of large-scale networks with perpetual RISs.Comment: 7 pages, 8 figure

Bulk material based thermoelectric energy harvesting for wireless sensor applications

The trend towards smart building and modern manufacturing demands ubiquitous sensing in the foreseeable future. Self-powered Wireless sensor networks (WSNs) are essential for such applications. This paper describes bulk material based thermoelectric generator (TEG) design and implementation for WSN. A 20cm2 Bi0.5Sb1.5Te3 based TEG was created with optimized configuration and generates 2.7mW in typical condition. A novel load matching method is used to maximize the power output. The implemented power management module delivers 651μW to WSN in 50 °C. With average power consumption of Tyndall WSN measured at 72μW, feasibility of utilizing bulk material TEG to power WSN is demonstrated

Récupération d'Energie Biomécanique et Systèmes Autonomes

National audienceLa récupération d'énergie (Energy Harvesting) est une thématique en plein essor visant à utiliser l'énergie ambiante (lumière, vibrations, gradients thermiques) présente dans l'environnement direct de dispositifs électroniques (capteurs, équipements mobiles) pour les alimenter, de façon à prolonger leur durée de fonctionnement, voire à les rendre totalement autonomes. La récupération d'énergie est généralement mise en œuvre pour alimenter de petits systèmes électroniques tels que des capteurs autonomes communicants pour le transport, l'industrie ou l'habitat du fait des puissances récupérées assez faibles; appliquée au cas de l'Homme, la récupération d'énergie peut atteindre des puissances de plusieurs milliwatts voire de plusieurs watts permettant d'alimenter des systèmes plus complexes tels que des lecteurs MP3, des téléphones portables ou des systèmes de localisation GPS. De nombreuses sources d'énergie présentes dans l'environnement de l'Homme peuvent être exploitées: le soleil, le gradient thermique entre la peau et l'extérieur, la déformation des vêtements, les contraintes dans les chaussures... . Cet article se focalise plus particulièrement sur la récupération d'énergie mécanique issue du corps humain et présente des exemples de dispositifs et d'applications issus de l'état de l'art montrant que la récupération d'énergie est déjà une réalité; et qu'elle permettra sur le plus long terme d'alimenter des dispositifs placés directement à l'intérieur du corps humain tels que des implants médicaux ou des pacemakers

Power supply based on inductive harvesting from structural currents

Monitoring infrastructure offers functional optimisation, lower maintenance cost, security, stability and data analysis benefits. Sensor nodes require some level of energy autonomy for reliable and cost-effective operation, and energy harvesting methods have been developed in the last two decades for this purpose. Here, a power supply that collects, stores and delivers regulated power from the stray magnetic field of currentcarrying structures is presented. In cm-scale structures the skin effect concentrates current at edges at frequencies even below 1 kHz. A coil-core inductive transducer is designed. A fluxfunnelling soft magnetic core shape is used, multiplying power density by the square of funnelling ratio. A power management circuit combining reactance cancellation, voltage doubling, rectification, super-capacitor storage and switched inductor voltage boosting and regulation is introduced. The power supply is characterised in house and on a full-size industrial setup, demonstrating a power reception density of 0.36 mW/cm3, 0.54 mW/cm3 and 0.73 mW/cm3 from a 25 A RMS structural current at 360 Hz, 500 Hz and 800 Hz respectively, corresponding to the frequency range of aircraft currents. The regulated output is tested under various loads and cold starting is demonstrated. The introduced method may enable power autonomy to wireless sensors deployed in current-carrying infrastructure

POWER DISTRIBUTION ANALYSIS IN COMPLEX SYSTEMS

Electronic systems are continuously growing nowadays in every ambit and application; concepts like mobile systems, domotic, wireless monitoring are becoming very common, and the reason is the continuous reduction of the energy and time needed to collect, process and send information and data to the end user. The energy management complexity of these systems is increasing in parallel both in terms of efficiency and reliability, in order to increase the lifetime of the application and try to make it energy-autonomous, thus also the power management should not be seen only as an efficient energy conversion stage, but as a complex system which can now manage different energy sources, and ensure an uninterrupted power supply to the application. The problems that must be overcome increase as the number of scenarios where the end applications have to be used: this thesis aims to present some complex power distribution systems and provide a detailed analysis of the strategies necessary to make the solution reliable and efficient

Portable Bio-Devices: Design of Electrochemical Instruments from Miniaturized to Implantable Devices

The integration of biosensors and electronic technologies allows the development of biomedical systems able to diagnose and monitoring pathologies by detecting specific biomarkers. The chapter presents the main modules involved in the development of such devices, generically represented in Fig. 1, and focuses its attention on the essential components of these systems to address questions such as: how is the device powered? How does it communicate the measured data? What kind of sensors could be used?, and What kinds of electronics are used

DC/DC converter 3D assembly for autonomous sensor nodes

This paper reports on the design and the manufacturing of an integrated DCDC converter, which respects the specificity of sensor node network: compactness, high efficiency in acquisition and transmission modes, and compatibility with miniature Lithium batteries. A novel integrated circuit (ASIC) has been designed and manufactured to provide regulated Voltage to the sensor node from miniaturized, thin film Lithium batteries. Then, a 3D integration technique has been used to integrate this ASIC in a 3 layers stack with high efficiency passives components, mixing the wafer level technologies from two different research institutions. Electrical results have demonstrated the feasibility of this integrated system and experiments have shown significant improvements in the case of oscillations in regulated voltage. However, stability of this output voltage toward the input voltage has still to be improved

An Ultra-wideband Battery-less Positioning System for Space Applications

An ultra-wide bandwidth (UWB) remote-powered positioning system for potential use in tracking floating objects inside space stations is presented. It makes use of battery-less tags that are powered-up and addressed through wireless power transfer in the UHF band and embed an energy efficient pulse generator in the 3-5 GHz UWB band. The system has been mounted on the ESA Mars Rover prototype to demonstrate its functionality and performance. Experimental results show the feasibility of centimeter-level localization accuracy at distances larger than 10 meters, with the capability of determining the position of multiple tags using a 2W-ERP power source in the UHF RFID frequency band.Comment: Published in: 2019 IEEE International Conference on RFID Technology and Applications (RFID-TA