Micro-Switch Design and Its Optimization Using Pattern Search Algorithm for Application in Reconfigurable Antenna

This chapter reports the design and optimization algorithm of metal-contact RF microswitch. Various important evolutionary optimization techniques that can be used to optimize non-linear and even non-differentiable types of radio frequency (RF) circuit’s problems are also reviewed. The transient response of the proposed switch shows displacement time (i.e., squeezed-film damping effect) of 5.0 μs and pull-in voltage varying from 9.0 to 9.25 V. Primarily, the switch exhibits insertion loss of 0.15 to 0.51 dB in on-position and isolation of 75.96 to 35.83 dB in off-position at 0.1–10 GHz. Also, the proposed RF switch equivalent circuit and layout are validated in ADS software which was earlier simulated in HFSS. A pattern search (PS) algorithm is used to optimize RF characteristics of the proposed switch after a brief review of the different optimization techniques. After optimization, the switch shows decrement in insertion loss and increment in isolation at 0.1–10 GHz. Further, two such optimized switches are introduced on the defected ground structure (DGS) antenna to make it reconfigurable in terms of frequency. Reconfigurable antenna (RA) is simulated using HFSS software and simulation results are verified by showing the mark of agreement with the fabrication results. The novelty in the proposed design is due to dual-band behavior and better resonance performance than antennas available in the literature. Attractions of proposed RA are its miniaturization and its utility in IEEE US S-(2.0–4.0 GHz) and C-(4.0–8.0 GHz) band

Communication Subsystems for Emerging Wireless Technologies

The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels

Multi-objective Synthesis of Antennas from Special and Conventional Materials

In the paper, we try to provide a comprehensive look on a multi-objective design of radiating, guiding and reflecting structures fabricated both from special materials (semiconductors, high-impedance surfaces) and conventional ones (microwave substrates, fully metallic antennas). Discussions are devoted to the proper selection of the numerical solver used for evaluating partial objectives, to the selection of the domain of analysis, to the proper formulation of the multi-objective function and to the way of computing the Pareto front of optimal solutions (here, we exploit swarm-intelligence algorithms, evolutionary methods and self-organizing migrating algorithms). The above-described approaches are applied to the design of selected types of microwave antennas, transmission lines and reflectors. Considering obtained results, the paper is concluded by generalizing remarks

Comparative Analysis of Linear and Nonlinear Pattern Synthesis of Hemispherical Antenna Array Using Adaptive Evolutionary Techniques

Hemispherical antenna arrays are subjected to linear and nonlinear synthesis and are optimized using adaptive based differential evolution (ADE) and fire fly (AFA) algorithm. The hemispherical shaped array with isotropic elements is considered. Antenna element parameters that are used for synthesis are excitation amplitude and angular position. Linear synthesis is termed as the variation in the element excitation amplitude and nonlinear synthesis is process of variation in element angular position. Both ADE and AFA are a high-performance stochastic evolutionary algorithm used to solve N-dimensional problems. These methods are used to determine a set of parameters of antenna elements that provide the desired radiation pattern. The effectiveness of the algorithms for the design of conformal antenna array is shown by means of numerical results. Comparison with other methods is made whenever possible. The results reveal that nonlinear synthesis, aided by the discussed techniques, provides considerable enhancements compared to linear synthesis

Particle Swarm Optimization

Particle swarm optimization (PSO) is a population based stochastic optimization technique influenced by the social behavior of bird flocking or fish schooling.PSO shares many similarities with evolutionary computation techniques such as Genetic Algorithms (GA). The system is initialized with a population of random solutions and searches for optima by updating generations. However, unlike GA, PSO has no evolution operators such as crossover and mutation. In PSO, the potential solutions, called particles, fly through the problem space by following the current optimum particles. This book represents the contributions of the top researchers in this field and will serve as a valuable tool for professionals in this interdisciplinary field

Bio-inspired optimization algorithms for smart antennas

This thesis studies the effectiveness of bio-inspired optimization algorithms in controlling adaptive antenna arrays. Smart antennas are able to automatically extract the desired signal from interferer signals and external noise. The angular pattern depends on the number of antenna elements, their geometrical arrangement, and their relative amplitude and phases. In the present work different antenna geometries are tested and compared when their array weights are optimized by different techniques. First, the Genetic Algorithm and Particle Swarm Optimization algorithms are used to find the best set of phases between antenna elements to obtain a desired antenna pattern. This pattern must meet several restraints, for example: Maximizing the power of the main lobe at a desired direction while keeping nulls towards interferers. A series of experiments show that the PSO achieves better and more consistent radiation patterns than the GA in terms of the total area of the antenna pattern. A second set of experiments use the Signal-to-Interference-plus-Noise-Ratio as the fitness function of optimization algorithms to find the array weights that configure a rectangular array. The results suggest an advantage in performance by reducing the number of iterations taken by the PSO, thus lowering the computational cost. During the development of this thesis, it was found that the initial states and particular parameters of the optimization algorithms affected their overall outcome. The third part of this work deals with the meta-optimization of these parameters to achieve the best results independently from particular initial parameters. Four algorithms were studied: Genetic Algorithm, Particle Swarm Optimization, Simulated Annealing and Hill Climb. It was found that the meta-optimization algorithms Local Unimodal Sampling and Pattern Search performed better to set the initial parameters and obtain the best performance of the bio-inspired methods studied

A novel design approach for 5G massive MIMO and NB-IoT green networks using a hybrid Jaya-differential evolution algorithm

Our main objective is to reduce power consumption by responding to the instantaneous bit rate demand by the user for 4th Generation (4G) and 5th Generation (5G) Massive MIMO network configurations. Moreover, we present and address the problem of designing green LTE networks with the Internet of Things (IoT) nodes. We consider the new NarrowBand-IoT (NB-IoT) wireless technology that will emerge in current and future access networks. In this context, we apply emerging evolutionary algorithms in the context of green network design. We investigate three different cases to show the performance of the new proposed algorithm, namely the 4G, 5G Massive MIMO, and the NB-IoT technologies. More specifically, we investigate the Teaching-Learning-Optimization (TLBO), the Jaya algorithm, the self-adaptive differential evolution jDE algorithm, and other hybrid algorithms. We introduce a new hybrid algorithm named Jaya-jDE that uses concepts from both Jaya and jDE algorithms in an effective way. The results show that 5G Massive MIMO networks require about 50% less power consumption than the 4G ones, and the NB-IoT in-band deployment requires about 10% less power than guard-band deployment. Moreover, Jaya-jDE emerges as the best algorithm based on the results

Scan matching by cross-correlation and differential evolution

Scan matching is an important task, solved in the context of many high-level problems including pose estimation, indoor localization, simultaneous localization and mapping and others. Methods that are accurate and adaptive and at the same time computationally efficient are required to enable location-based services in autonomous mobile devices. Such devices usually have a wide range of high-resolution sensors but only a limited processing power and constrained energy supply. This work introduces a novel high-level scan matching strategy that uses a combination of two advanced algorithms recently used in this field: cross-correlation and differential evolution. The cross-correlation between two laser range scans is used as an efficient measure of scan alignment and the differential evolution algorithm is used to search for the parameters of a transformation that aligns the scans. The proposed method was experimentally validated and showed good ability to match laser range scans taken shortly after each other and an excellent ability to match laser range scans taken with longer time intervals between them.Web of Science88art. no. 85

Modeling EMI Resulting from a Signal Via Transition Through Power/Ground Layers

Signal transitioning through layers on vias are very common in multi-layer printed circuit board (PCB) design. For a signal via transitioning through the internal power and ground planes, the return current must switch from one reference plane to another reference plane. The discontinuity of the return current at the via excites the power and ground planes, and results in noise on the power bus that can lead to signal integrity, as well as EMI problems. Numerical methods, such as the finite-difference time-domain (FDTD), Moment of Methods (MoM), and partial element equivalent circuit (PEEC) method, were employed herein to study this problem. The modeled results are supported by measurements. In addition, a common EMI mitigation approach of adding a decoupling capacitor was investigated with the FDTD method