Mechanics of Non Planar Interfaces in Flip-Chip Interconnects

With the continued proliferation of low cost, portable consumer electronic products with greater functionality, there is increasing demand for electronic packaging that is smaller, lighter and less expensive. Flip chip is an essential enabling technology for these products. The electrical connection between the chip I/O and substrate is achieved using conductive materials, such as solder, conductive epoxy, metallurgy bump (e.g., gold) and anisotropic conductive adhesives. The interconnect regions of flip-chip packages consists of highly dissimilar materials to meet their functional requirements. The mismatches in properties, contact morphology and crystal orientation at those material interfaces make them vulnerable to failure through delamination and crack growth under various loading patterns. This study encompasses contact between deformable bodies, bonding at the asperities and fracture properties at interfaces formed by the interconnects of flip-chip packages. This is achieved through experimentation and modeling at different length scales, to be able to capture the detailed microstructural features and contact mechanics at interfaces typically found in electronic systems

The effect of co-planarity variation on anisotropic conductive adhesive assemblies

Anisotropic Conductive Adhesives (ACAs) consist of a polymer adhesive matrix containing fine conductive particles dispersed either randomly, or more rarely in an ordered way. The primary objective of this experimental research was to understand the effects of a non-uniform bond thickness due to non co-planarity of the component or substrate terminations in ACA assemblies. This has been achieved through measurements of the conductivity variations of ACA joints in a number of ACA assemblies, where the component bump plane and substrate plane were deliberately held in different degrees of relative rotation from parallel during adhesive cure. Measurements of the joint resistances versus rotational angle, for a constant bonding force, were made for 10 levels of rotation of the chips relative to the substrates. The results showed that the resistances of the joints in the assemblies exhibited three distinct types of behaviour: stable joint resistances; gradually increasing resistances and unstable resistances. In conclusion, it is shown that ACA joints are very sensitive to the uniformity of the bond thickness, as the larger the rotations were, the lower and less uniform the joint conductivities were, however, the joints were uniform if the rotation angles were controlled within certain limits

Nanowires for 3d silicon interconnection – low temperature compliant nanowire-polymer film for z-axis interconnect

Semiconductor chip packaging has evolved from single chip packaging to 3D heterogeneous system integration using multichip stacking in a single module. One of the key challenges in 3D integration is the high density interconnects that need to be formed between the chips with through-silicon-vias (TSVs) and inter-chip interconnects. Anisotropic Conductive Film (ACF) technology is one of the low-temperature, fine-pitch interconnect method, which has been considered as a potential replacement for solder interconnects in line with continuous scaling of the interconnects in the IC industry. However, the conventional ACF materials are facing challenges to accommodate the reduced pad and pitch size due to the micro-size particles and the particle agglomeration issue. A new interconnect material - Nanowire Anisotropic Conductive Film (NW-ACF), composed of high density copper nanowires of ~ 200 nm diameter and 10-30 µm length that are vertically distributed in a polymeric template, is developed in this work to tackle the constrains of the conventional ACFs and serves as an inter-chip interconnect solution for potential three-dimensional (3D) applications

Mechanical and electrical characterisation of anisotropic conductive adhesive particles

This thesis presents research into the mechanical and electrical characterisation of Anisotropic Conductive Adhesive (ACA) particles and their behaviour within typical joints. A new technique has been developed for study of individual ACA particle mechanical and electrical performance when undergoing deformation. A study of the effects of planarity variations on individual electrical joints in real ACA assemblies is presented firstly, followed by the research on the mechanical deformation and electrical tests of individual ACA particles undergoing deformation. In the co-planarity research, experiments introducing deliberate rotation between a chip and substrate were designed and carried out to simulate planarity variations in ACA assemblies. There are two outputs from this part of the research. One is the planarity variation effects on individual electrical joints in ACA assemblies, and the other is the effect of bond thickness on the resistance of a real joint. [Continues.

Novel fine pitch interconnection methods using metallised polymer spheres

There is an ongoing demand for electronics devices with more functionality while reducing size and cost, for example smart phones and tablet personal computers. This requirement has led to significantly higher integrated circuit input/output densities and therefore the need for off-chip interconnection pitch reduction. Flip-chip processes utilising anisotropic conductive adhesives anisotropic conductive films (ACAs/ACFs) have been successfully applied in liquid crystal display (LCD) interconnection for more than two decades. However the conflict between the need for a high particle density, to ensure sufficient the conductivity, without increasing the probability of short circuits has remained an issue since the initial utilization of ACAs/ACFs for interconnection. But this issue has become even more severe with the challenge of ultra-fine pitch interconnection. This thesis advances a potential solution to this challenge where the conductive particles typically used in ACAs are selectively deposited onto the connections ensuring conductivity without bridging. The research presented in this thesis work has been undertaken to advance the fundamental understanding of the mechanical characteristics of micro-sized metal coated polymer particles (MCPs) and their application in fine or ultra-fine pitch interconnections. This included use of a new technique based on an in-situ nanomechanical system within SEM which was utilised to study MCP fracture and failure when undergoing deformation. Different loading conditions were applied to both uncoated polymer particles and MCPs, and the in-situ system enables their observation throughout compression. The results showed that both the polymer particles and MCP display viscoelastic characteristics with clear strain-rate hardening behaviour, and that the rate of compression therefore influences the initiation of cracks and their propagation direction. Selective particle deposition using electrophoretic deposition (EPD) and magnetic deposition (MD) of Ni/Au-MCPs have been evaluated and a fine or ultra-fine pitch deposition has been demonstrated, followed by a subsequent assembly process. The MCPs were successfully positively charged using metal cations and this charging mechanism was analysed. A new theory has been proposed to explain the assembly mechanism of EPD of Ni/Au coated particles using this metal cation based charging method. The magnetic deposition experiments showed that sufficient magnetostatic interaction force between the magnetized particles and pads enables a highly selective dense deposition of particles. Successful bonding to form conductive interconnections with pre-deposited particles have been demonstrated using a thermocompression flip-chip bonder, which illustrates the applicable capability of EPD of MCPs for fine or ultra-fine pitch interconnection

Die-Level Thinning for Flip-Chip Integration on Flexible Substrates

Die-level thinning, handling, and integration of singulated dies from multi-project wafers (MPW) are often used in research, early-stage development, and prototyping of flexible devices. There is a high demand for thin silicon devices for several applications, such as flexible electronics. To address this demand, we study a novel post-processing method on two silicon devices, an electrochemical impedance sensor, and Complementary Metal Oxide Semiconductor (CMOS) die. Both are drawn from an MPW batch, thinned at die-level after dicing and singulation down to 60 µm. The thinned dies were flip-chip bonded to flexible substrates and hermetically sealed by two techniques: thermosonic bonding of Au stud bumps and anisotropic conductive paste (ACP) bonding. The performance of the thinned dies was assessed via functional tests and compared to the original dies. Furthermore, the long-term reliability of the flip-chip bonded thinned sensors was demonstrated to be higher than the conventional wire-bonded sensors

Reliability analysis of foil substrate based integration of silicon chips

Flexible electronics has attracted significant attention in the recent past due to the booming wearables market in addition to the ever-increasing interest for faster, thinner and foldable mobile phones. Ultra-thin bare silicon ICs fabricated by thinning down standard ICs to thickness below 50 μm are flexible and therefore they can be integrated on or in polymer foils to create flexible hybrid electronic (FHE) components that could be used to replace rigid standard surface mount device (SMD) components. The fabricated FHE components referred as chip foil packages (CFPs) in this work are ideal candidates for FHE system integration owing to their ability to deliver high performance at low power consumption while being mechanically flexible. However, very limited information is available in the literature regarding the reliability of CFPs under static and dynamic bending. The lack of such vital information is a major obstacle impeding their commercialization. With the aim of addressing this issue, this thesis investigates the static and dynamic bending reliability of CFPs. In this scope, the static bending reliability of CFPs has been investigated in this thesis using flexural bending tests by measuring their fracture strength. Then, Finite Element Method (FEM) simulations have been implemented to calculate the fracture stress of ultra-thin flexible silicon chips where analytical formulas may not be applied. After calculating the fracture stress from FEM simulations, the enhancement in robustness of ultra-thin chips (UTCs) against external load has also been proved and quantified with further experimental investigations. Besides, FEM simulations have also been used to analyse the effect of Young’s Modulus of embedding materials on the robustness of the embedded UTCs. Furthermore, embedding the UTCs in polymer layers has also been experimentally proven to be an effective solution to reduce the influence of thinning and dicing induced damages on the robustness of the embedded UTCs. Traditional interconnection techniques such as wire bonding may not be implemented to interconnect ultra-thin silicon ICs owing to the high mechanical forces involved in the processes that would crack the chips. Therefore, two novel interconnection methods namely (i) flip-chip bonding with Anisotropic Conductive Adhesive (ACA) and (ii) face-up direct metal interconnection have been implemented in this thesis to interconnect ultra-thin silicon ICs to the corresponding interposer patterns on foil substrates. The CFP samples thus fabricated were then used for the dynamic bending reliability investigations. A custom-built test equipment was developed to facilitate the dynamic bending reliability investigations of CFPs. Experimental investigations revealed that the failure of CFPs under dynamic bending was caused mainly by the cracking of the redistribution layer (RDL) interconnecting the chip and the foil. Furthermore, it has also been shown that the CFPs are more vulnerable to repeated compressive bending than to repeated tensile bending. Then, the influence of dimensional factors such as the thickness of the chip as well as the RDL on the dynamic bending reliability of CFPs have also been studied. Upon identifying the plausible cause behind the cracking of the RDL leading to the failure of the CFPs, two methods to improve the dynamic bending reliability of the RDL have been suggested and demonstrated with experimental investigations. The experimental investigations presented in this thesis adds some essential information to the state-of-the-art concerning the static and the dynamic bending reliability of UTCs integrated in polymer foils that are not yet available in the literature and aids to establish in-depth knowledge of mechanical reliability of the components required for manufacturing future FHE systems. The strategies devised to enhance the robustness of UTCs and CFPs could serve as guidelines for fabricating reliable FHE components and systems

Development and reliability of a direct access sensor using flip chip on flex technology with anisotropic conductive adhesive

Technological developments in biomedical microsystems are opening up new opportunities to improve healthcare procedures. Swallowable diagnostic sensing capsules are an example of these. In none of the diagnostic sensing capsules, is the sensor’s first level packaging achieved via Flip Chip Over Hole (FCOH) method using Anisotropic Conductive Adhesive (ACA). In a capsule application with direct access sensor (DAS), ACA not only provides the electrical interconnection but simultaneously seals the interconnect area and the underlying electronics. The development showed that the ACA FCOH was a viable option for the DAS interconnection. Adequate adhesive formed a strong joint that withstood a shear stress of 120N/mm2 and a compressive stress of 6N required to secure the final sensor assembly in place before encapsulation. Electrical characterization of the ACA joint in a fluid environment showed that the ACA was saturated with moisture and that the ions in the solution actively contributed to the leakage current, characterized by the varying rate of change of conductance. Long term hygrothermal aging of the ACA joint showed that a thermal strain of 0.004 and a hygroscopic strain of 0.0052 were present and resulted in a fatigue like process. In-vitro tests showed that high temperature and acidity had a deleterious effect of the ACA and its joint. It also showed that the ACA contact joints positioned at around or over 1mm would survive the gastrointestinal (GI) fluids and would be able to provide a reliable contact during the entire 72hr of the GI transit time. A final capsule demonstrator was achieved by successfully integrating the DAS, the battery and the final foldable circuitry into a glycerine capsule. Final capsule soak tests suggested that the silicone encapsulated system could survive the 72hr gut transition

Copper to copper bonding by nano interfaces for fine pitch interconnections and thermal applications

Ever growing demands for portability and functionality have always governed the electronic technology innovations. IC downscaling with Moore s law at IC level and system miniaturization with System-On-Package (SOP) paradigm at system level, have resulted and will continue to result in ultraminiaturized systems with unprecedented functionality at reduced cost. However, system miniaturization poses several electrical and thermal challenges that demand innovative solutions including advanced materials, bonding and assembly techniques. Heterogeneous material and device integration for thermal structures and IC assembly are limited by the bonding technology and the electrical and thermal impedance of the bonding interfaces. Solder - based bonding technology that is prevalent today is a major limitation to future systems. The trend towards miniaturized systems is expected to drive downscaling of IC I/O pad pitches from 40µm to 1- 5µm in future. Solder technology imposes several pitch, processability and cost restrictions at such fine pitches. Furthermore, according to International Technology Roadmap for Semiconductors (ITRS-2006), the supply current in high performance microprocessors is expected to increase to 220 A by 2012. At such supply current, the current density will exceed the maximum allowable current density of solders. The intrinsic delay and electromigration in solders are other daunting issues that become critical at nanometer sized technology nodes. In addition, formation of intermetallics is also a bottleneck that poses significant mechanical issues. Similarly, thermal power dissipation is growing to unprecedented high with a projected power of 198 W by 2008 (ITRS 2006). Present thermal interfaces are not adequate for such high heat dissipation. Recently, copper based thin film bonding has become a promising approach to address the abovementioned challenges. However, copper-copper direct bonding without using solders has not been studied thoroughly. Typically, bonding is carried out at 400oC for 30 min followed by annealing for 30 min. High thermal budget in such process makes it less attractive for integrated systems because of the associated process incompatibilities. Hence, there is a need to develop a novel low temperature copper to copper bonding process. In the present study, nanomaterials - based copper-to-copper bonding is explored and developed as an alternative to solder-based bonding. To demonstrate fine pitch bonding, the patterning of these nanoparticles is crucial. Therefore, two novel self-patterning techniques based on: 1.) Selective wetting and 2.) Selective nanoparticle deposition, are developed to address this challenge. Nanoparticle active layer facilitates diffusion and, thus, a reliable bond can be achieved using less thermal budget. Quantitative characterization of the bonding revealed good metallurgical bonding with very high bond strength. This has been confirmed by several morphological and structural characterizations. A 30-micron pitch IC assembly test vehicle is used to demonstrate fine pitch patternability and bonding. In conclusion, novel nanoparticle synthesis and patterning techniques were developed and demonstrated for low-impedance and low-cost electrical and thermal interfaces.M.S.Committee Chair: Rao R. Tummala; Committee Member: C. P. Wong; Committee Member: P. M. Ra