159 research outputs found

    Output Power and Gain Monitoring in RF CMOS Class A Power Amplifiers by Thermal Imaging

    Get PDF
    © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.The viability of using off-chip single-shot imaging techniques for local thermal testing in integrated Radio Frequency (RF) power amplifiers (PA’s) is analyzed. With this approach, the frequency response of the output power and power gain of a Class A RF PA is measured, also deriving information about the intrinsic operation of its transistors. To carry out this case study, the PA is heterodynally driven, and its electrical behavior is down converted into a lower frequency thermal field acquirable with an InfraRed Lock-In Thermography (IR-LIT) system. After discussing the theory, the feasibility of the proposed approach is demonstrated and assessed with thermal sensors monolithically integrated in the PA. As crucial advantages to RF-testing, this local approach is noninvasive and demands less complex instrumentation than the mainstream commercially available solutions.Peer ReviewedPostprint (author's final draft

    Exergy-based Planning and Thermography-based Monitoring for energy efficient buildings - Progress Report (KIT Scientific Reports ; 7632)

    Get PDF
    Designing and monitoring energy efficiency of buildings is vital since they account for up to 40% of end-use energy. In this study, exergy analysis is investigated as a life cycle design tool to strike a balance between thermodynamic efficiency of energy conversion and economic and environmental costs of construction. Quantitative geo-referenced thermography is proposed for monitoring and quantitative assessment via continued simulation and parameter estimation during the operating phase

    Strain state detection in composite structures: Review and new challenges

    Get PDF
    Developing an advanced monitoring system for strain measurements on structural components represents a significant task, both in relation to testing of in-service parameters and early identification of structural problems. This paper aims to provide a state-of-the-art review on strain detection techniques in composite structures. The review represented a good opportunity for direct comparison of different novel strain measurement techniques. Fibers Bragg grating (FBG) was discussed as well as non-contact techniques together with semiconductor strain gauges (SGs), specifically infrared (IR) thermography and the digital image correlation (DIC) applied in order to detect strain and failure growth during the tests. The challenges of the research community are finally discussed by opening the current scenario to new objectives and industrial applications

    Strain State Detection in Composite Structures: Review and New Challenges

    Get PDF
    Developing an advanced monitoring system for strain measurements on structural components represents a significant task, both in relation to testing of in-service parameters and early identification of structural problems. This paper aims to provide a state-of-the-art review on strain detection techniques in composite structures. The review represented a good opportunity for direct comparison of different novel strain measurement techniques. Fibers Bragg grating (FBG) was discussed as well as non-contact techniques together with semiconductor strain gauges (SGs), specifically infrared (IR) thermography and the digital image correlation (DIC) applied in order to detect strain and failure growth during the tests. The challenges of the research community are finally discussed by opening the current scenario to new objectives and industrial applications

    A Review of Structural Health Monitoring Techniques as Applied to Composite Structures.

    Get PDF
    Structural Health Monitoring (SHM) is the process of collecting, interpreting, and analysing data from structures in order to determine its health status and the remaining life span. Composite materials have been extensively use in recent years in several industries with the aim at reducing the total weight of structures while improving their mechanical properties. However, composite materials are prone to develop damage when subjected to low to medium impacts (ie 1 – 10 m/s and 11 – 30 m/s respectively). Hence, the need to use SHM techniques to detect damage at the incipient initiation in composite materials is of high importance. Despite the availability of several SHM methods for the damage identification in composite structures, no single technique has proven suitable for all circumstances. Therefore, this paper offers some updated guidelines for the users of composites on some of the recent advances in SHM applied to composite structures; also, most of the studies reported in the literature seem to have concentrated on the flat composite plates and reinforced with synthetic fibre. There are relatively fewer stories on other structural configurations such as single or double curve structures and hybridised composites reinforced with natural and synthetic fibres as regards SHM

    Towards a More Flexible, Sustainable, Efficient and Reliable Induction Cooking: A Power Semiconductor Device Perspective

    Get PDF
    Esta tesis tiene como objetivo fundamental la mejora de la flexibilidad, sostenibilidad, eficiencia y fiabilidad de las cocinas de inducción por medio de la utilización de dispositivos semiconductores de potencia: Dentro de este marco, existe una funcionalidad que presenta un amplio rango de mejora. Se trata de la función de multiplexación de potencia, la cual pretende resolverse de una manera más eficaz por medio de la sustitución de los comúnmente utilizados relés electromecánicos por dispositivos de estado sólido. De entre todas las posibles implementaciones, se ha identificado entre las más prometedoras a aquellas basadas en dispositivos de alta movilidad de electrones (HEMT) de Nitruro de Galio (GaN) y de aquellas basadas en Carburo de Silicio (SiC), pues presentan unas características muy superiores a los relés a los que se pretende sustituir. Por el contrario, otras soluciones que inicialmente parecían ser muy prometedoras, como los MOSFETs de Súper-Unión, han presentado una serie de comportamientos anómalos, que han sido estudiados minuciosamente por medio de simulaciones físicas a nivel de chip. Además, se analiza en distintas condiciones la capacidad en cortocircuito de dispositivos convencionalmente empleados en cocinas de inducción, como son los IGBTs, tratándose de encontrar el equilibrio entre un comportamiento robusto al tiempo que se mantienen bajas las pérdidas de potencia. Por otra parte, también se estudia la robustez y fiabilidad de varios GaN HEMT de 600- 650 V tanto de forma experimental como por medio de simulaciones físicas. Finalmente se aborda el cálculo de las pérdidas de potencia en convertidores de potencia resonantes empleando técnicas de termografía infrarroja. Por medio de esta técnica no solo es posible medir de forma precisa las diferentes contribuciones de las pérdidas, sino que también es posible apreciar cómo se distribuye la corriente a nivel de chip cuando, por ejemplo, el componente opera en modo de conmutación dura. Como resultado, se obtiene información relevante relacionada con modos de fallo. Además, también ha sido aprovechar las caracterizaciones realizadas para obtener un modelo térmico de simulación.This thesis is focused on addressing a more flexible, sustainable, efficient and reliable induction cooking approach from a power semiconductor device perspective. In this framework, this PhD Thesis has identified the following activities to cover such demands: In view of the growing interest for an effective power multiplexing in Induction Heating (IH) applications, improved and efficient Solid State Relays (SSRs) as an alternative to the electromechanical relays (EMRs) are deeply investigated. In this context, emerging Gallium Nitride (GaN) High‐Electron‐Mobility Transistors (GaN HEMTs) and Silicon Carbide (SiC) based devices are identified as potential candidates for the mentioned application, featuring several improved characteristics over EMRs. On the contrary, other solutions, which seemed to be very promising, resulted to suffer from anomalous behaviors; i.e. SJ MOSFETs are thoroughly analysed by electro‐thermal physical simulations at the device level. Additionally, the Short Circuit (SC) capability of power semiconductor devices employed or with potential to be used in IH appliances is also analysed. On the one hand, conventional IGBTs SC behavior is evaluated under different test conditions so that to obtain the trade‐off between ruggedness and low power losses. Moreover, ruggedness and reliability of several normally‐off 600‐650 V GaN HEMTs are deeply investigated by experimentation and physics‐based simulation. Finally, power losses calculation at die‐level is performed for resonant power converters by means of using Infrared Thermography (IRT). This method assists to determine, at the die‐level, the power losses and current distribution in IGBTs used in resonant soft‐switching power converters when functioning within or outside the Zero Voltage Switching (ZVS) condition. As a result, relevant information is obtained related to decreasing the power losses during commutation in the final application, and a thermal model is extracted for simulation purposes.<br /

    Laser Reflectance Modulation in Silicon Integrated Circuits

    Get PDF
    Ph.DDOCTOR OF PHILOSOPH

    Non-destructive Testing in Civil Engineering

    Get PDF
    This Special Issue, entitled “Non-Destructive Testing in Civil Engineering”, aims to present to interested researchers and engineers the latest achievements in the field of new research methods, as well as the original results of scientific research carried out with their use—not only in laboratory conditions but also in selected case studies. The articles published in this Special Issue are theoretical–experimental and experimental, and also show the practical nature of the research. They are grouped by topic, and the main content of each article is briefly discussed for your convenience. These articles extend the knowledge in the field of non-destructive testing in civil engineering with regard to new and improved non-destructive testing (NDT) methods, their complementary application, and also the analysis of their results—including the use of sophisticated mathematical algorithms and artificial intelligence, as well as the diagnostics of materials, components, structures, entire buildings, and interesting case studies

    Transfer function analysis as a novel diagnostic tool for polymer electrolyte membrane fuel cells

    Get PDF
    Polymer electrolyte membrane fuel cells have shown great promise as a clean and renewable energy source due to their high efficiency and lack of carbon emissions at point of use. However, one of the great challenges in their wider commercialisation is the lack of in-situ metrological techniques to measure performance of the devices over the course of their lifetime. In this work, novel transfer function analysis techniques are developed and applied to these devices to better understand their in-situ performance through perturbation and measurement of electrical, thermal, and pneumatic properties. Localised electrochemical impedance spectroscopy measurements using a novel reference electrode array are made to measure spatially resolved, cathode-specific fuel cell performance for the first time as well as membrane hydration transients when the fuel cell is polarised from open circuit. Electro-thermal impedance spectroscopy, a transfer function technique relating an electrical perturbation to a thermal response, is developed to characterise the electrically-dependent thermal performance of an open-cathode fuel cell and identify faults such as pinhole formation and bowing of lands. Electrochemical pressure impedance spectrscopy, a transfer function technique relating a cathodic pressure perturbation to an electrical response, is developed and applied to a fuel cell in order to characterise water management of a fuel cell under varying humidity conditions. The impact of the techniques developed is discussed with scope for further advancement deliberated. The relevance of the application of the techniques is highlighted to give novel and complementary information not easily accessible by more conventional metrological methodologies
    corecore