Direct Torque Control for Silicon Carbide Motor Drives

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives. To overcome the above challenges, a SiC T-type neutral point clamped (NPC) inverter is studied in this work to significantly reduce the torque and flux ripples which also effectively reduce the stator current ripples, while retaining the fast-dynamic response as the conventional DTC. The unbalanced DC-link is an intrinsic issue of the T-type inverter, which may also lead to higher torque ripple. To address this issue, a novel DTC algorithm, which only utilizes the real voltage space vectors and the virtual space vectors (VSVs) that do not contribute to the neutral point current, is proposed to achieve inherent dc-link capacitor voltage balancing without using any DC-link voltage controls or additional DC-link capacitor voltages and/or neutral point current sensors. Both dynamic performance and efficiency are critical for the interior permanent-magnet (IPM) motor drives for transportation applications. It is critical to determine the optimal reference stator flux linkage to improve the efficiency further of DTC drives and maintain the stability of the drive system, which usually obtained by tuning offline and storing in a look-up table or calculated online using machine models and parameters. In this work, the relationship between the stator flux linkage and the magnitude of stator current is analyzed mathematically. Then, based on this relationship, a perturb and observe (P&O) method is proposed to determine the optimal flux for the motor which does not need any prior knowledge of the machine parameters and offline tuning. However, due to the fixed amplitude of the injected signal the P&O algorithm suffers from large oscillations at the steady state conditions. To mitigate the drawback of the P&O method, an adaptive high frequency signal injection based extremum seeking control (ESC) algorithm is proposed to determine the optimal reference flux in real-time, leading to a maximum torque per ampere (MTPA) like approach for DTC drives. The stability analysis and key parameters selection for the proposed ESC algorithm are studied. The proposed method can effectively reduce the motor copper loss and at the same time eliminate the time consuming offline tuning effort. Furthermore, since the ESC is a model-free approach, it is robust against motor parameters variations, which is desirable for IPM motors

Critical Aspects of Electric Motor Drive Controllers and Mitigation of Torque Ripple - Review

Electric vehicles (EVs) are playing a vital role in sustainable transportation. It is estimated that by 2030, Battery EVs will become mainstream for passenger car transportation. Even though EVs are gaining interest in sustainable transportation, the future of EV power transmission is facing vital concerns and open research challenges. Considering the case of torque ripple mitigation and improved reliability control techniques in motors, many motor drive control algorithms fail to provide efficient control. To efficiently address this issue, control techniques such as Field Orientation Control (FOC), Direct Torque Control (DTC), Model Predictive Control (MPC), Sliding Mode Control (SMC), and Intelligent Control (IC) techniques are used in the motor drive control algorithms. This literature survey exclusively compares the various advanced control techniques for conventionally used EV motors such as Permanent Magnet Synchronous Motor (PMSM), Brushless Direct Current Motor (BLDC), Switched Reluctance Motor (SRM), and Induction Motors (IM). Furthermore, this paper discusses the EV-motors history, types of EVmotors, EV-motor drives powertrain mathematical modelling, and design procedure of EV-motors. The hardware results have also been compared with different control techniques for BLDC and SRM hub motors. Future direction towards the design of EV by critical selection of motors and their control techniques to minimize the torque ripple and other research opportunities to enhance the performance of EVs are also presented.publishedVersio

Online loss minimization based direct torque and flux control of IPMSM drive

With the advent of high energy rare earth magnetic material such as, third generation neodymium-iron-boron (NdFeB), permanent magnet synchronous motor (PMSM) is becoming more and more popular in high power industrial applications (e.g., high-speed railway) due to its advantageous features such as high energy density, stable parameters, high power factor, low noise and high efficiency as compared to the conventional ac motors. Over the years, vector control and direct torque and flux control (DTFC) techniques have been used for high performance motor drives. But, the DTFC is faster than that of conventional vector control as the DTFC scheme doesn't need any coordinate transformation, pulse width modulation (PWM) and current regulators. The DTFC utilizes hysteresis band comparators for both flux and torque controls. Most of the past researches on DTFC based motor drives mainly concentrated on the development of the inverter control algorithm with less torque ripple as it is the major drawback of DTFC. The torque reference value is obtained online based on motor speed error between actual and reference values through a speed controller. Traditionally, researchers chose a constant value of air-gap flux reference based on trial and error method which may not be acceptable for high performance drives as the air-gap flux changes with operating conditions and system disturbance. Efficient high performance drives require fast and accurate speed response to cope with disturbances and algorithm to minimize motor losses. However, if the reference air-gap flux is maintained constant it is not possible to control the motor losses. Therefore, this thesis presents a novel loss minimization based DTFC scheme for interior type PMSM drive so that the drive system can maintain both high efficiency and high dynamic performance. An online model based loss minimization algorithm (LMA) is developed to estimate the air-gap flux so that the motor operates at minimum loss condition while taking the general advantages of DTFC over conventional vector control. The performance the proposed LMA based DTFC for PMSM drive is tested in both simulation and real-time implementation at different operating conditions. The results verify the effectiveness of the proposed flux observer based DTFC scheme for PMSM drive

Advances in Rotating Electric Machines

It is difficult to imagine a modern society without rotating electric machines. Their use has been increasing not only in the traditional fields of application but also in more contemporary fields, including renewable energy conversion systems, electric aircraft, aerospace, electric vehicles, unmanned propulsion systems, robotics, etc. This has contributed to advances in the materials, design methodologies, modeling tools, and manufacturing processes of current electric machines, which are characterized by high compactness, low weight, high power density, high torque density, and high reliability. On the other hand, the growing use of electric machines and drives in more critical applications has pushed forward the research in the area of condition monitoring and fault tolerance, leading to the development of more reliable diagnostic techniques and more fault-tolerant machines. This book presents and disseminates the most recent advances related to the theory, design, modeling, application, control, and condition monitoring of all types of rotating electric machines

Sensorless SVPWM-FADTC of a new flux-modulated permanent-magnet wheel motor based on a wide-speed sliding mode observer

published_or_final_versio

A Novel DTFC Based Efficiency and Dynamic Performance Improvement of IPMSM Drive

With the advancements in magnetic materials and semiconductor technology, permanent magnet synchronous motor (PMSM) is becoming more and more popular in high power industrial applications due to its high energy density, high power factor, low noise and high efficiency as compared to conventional AC motors. Field oriented vector control (VC) and direct torque and flux control (DTFC) are used for high performance drives. Among these two techniques DTFC is faster and simpler than that of conventional VC scheme as DTFC scheme doesn’t need any coordinate transformation, pulse width modulation and current regulators. The DTFC based motor drives utilizes hysteresis band comparators for both torque and flux controls. Both torque and flux are controlled simultaneously by the selection of appropriate voltage vectors from the inverter. However, DTFC suffers from high torque ripples due to discrete nature of control system and limited voltage vectors from the inverter. Torque ripples can be minimized by increasing the sector numbers of the DTFC scheme which increases the switching frequency of the inverter. Traditionally, researchers chose a constant value of reference air-gap flux to make the control task easy but it is not acceptable for high performance drives as the air-gap flux changes with the operating conditions and system disturbances. Furthermore, if the reference air-gap flux is maintained constant, it is not possible to control the motor over the wide speed range operation. Moreover, conventional six-sector based DTFC scheme suffers from high torque ripples, which is the major drawbacks to achieve high dynamic performance. Therefore, this thesis presents a novel eighteen-sector based DTFC scheme to achieve high dynamic performance with minimum torque ripples. In addition, the loss minimization algorithm (LMA) is incorporated with proposed DTFC scheme in order to improve the efficiency while maintaining high dynamic performance. This thesis further presents modified eighteen-sector based DTFC scheme to overcome the unbalanced voltage effects in any sector of conventional six-sector based system to improve the dynamic performance of the proposed system. This thesis also presents a novel sector determination algorithm to determine the sector number of the stator flux linkage vector which reduces the computational burden to the microprocessor. A five level torque hysteresis comparator based DTFC scheme is also proposed to reduce the torque ripple. Further, a backstepping based nonlinear controller is developed for IPMSM drive that achieves the lowest possible torque ripples in steady state. In this controller development, the control variable is motor electromagnetic developed torque and stator air-gap flux linkages similar to classical DTFC but the errors are forced to zero using backstepping process to get better dynamic performance. The effectiveness of the proposed systems is verified through the development of a simulation model using Matlab/Simulink. Performance of the proposed nonlinear controller is investigated extensively at different operating conditions such as sudden speed and load changes. Then the complete IPMSM drives, incorporating the proposed LMA and eighteen-sector based DTFC scheme and nonlinear controller with torque and flux as virtual control variables are successfully implemented in real-time using digital signal processor (DSP) board-DS1104 board for laboratory 5-hp motor. The effectiveness of the proposed control techniques are verified in both simulation and experiment at different operating conditions. It is found that, the nonlinear controller based IPMSM drive provides the best performance in terms of torque ripple among all the DTFC scheme developed in the thesis. The results show the robustness of the drive and it’s potentiality to apply for real-time industrial drive applications

A novel switching table for a modified three-level inverter-fed DTC drive with torque and flux ripple minimization

The use of a direct torque control (DTC) drive is a well-known control strategy that is applied frequently to induction motors. Although torque and stator flux ripples are major disadvantages of this approach, using a higher-level inverter helps to overcome these issues. In this paper, we propose a novel switching table with a modified control strategy for a three-level inverter to achieve ripple minimization, as well as smooth switching and neutral point balance; the latter features are generally ignored in many works. The proposed model is compared with a conventional DTC and an improved three-level inverter-fed voltage vector synthesis model in the Matlab/Simulink® environment with low, normal, and high-speed operation under load torque disturbances. The performance indexes and the comparative results confirm the effectiveness of the proposed model in reducing the torque and stator flux ripples by up to 70% and 78%, respectively, generating a lower total harmonic distortion (THD%) in all scenarios, in addition to maintaining the neutral point balance and preventing voltage jumps across the switches of the inverter

Performance enhancement of direct torque-controlled permanent magnet synchronous motor with a flexible switching table

In this paper, a flexible switching table (FST) for direct torque control (DTC) of permanent magnet synchronous motors (PMSMs) was proposed to enhance the steady-state and dynamic performances of the drive system. First, the influence of each converter output voltage vectors on the torque and stator flux deviation rates was analyzed to assess the voltage selection strategies of the conventional STs and their impact on the DTC system’s performance. Then, a new flexible ST was proposed which uses a simple algorithm to adaptively select the appropriate voltage vector for two of its states according to the system operating condition. The effectiveness and feasibility of the proposed FST were verified through a comparative evaluation with the conventional STs using experimental results obtained from a 0.75 kW PMSM drive system

Implementation and Analysis of Direct Torque Control for Permanent Magnet Synchronous Motor Using Gallium Nitride based Inverter

Permanent magnet synchronous machines (PMSMs) attract considerable attention in various industrial applications, such as electric and hybrid electric vehicles, due to their high efficiency and high-power density. In this thesis, the mathematical model of PMSM and two popular control strategies, field-oriented control (FOC) and direct torque control (DTC), are analyzed and compared. The results demonstrated that the DTC has better dynamic response in comparison to FOC. Moreover, DTC can eliminate the use of position sensor, which will save the cost of the PMSM drive system. Therefore, this thesis focuses on the design and implementation of high-performance DTC for PMSMs with a Gallium Nitride (GaN) based high switching frequency motor drive. First, the characteristics and operation principles of a PMSM are introduced. Then, the mathematical models of a PMSM under different coordinate systems are investigated. Consequently, a PMSM model is developed based on the dq rotating reference frame and implemented in the MATLAB/Simulink for validation. Two advanced PMSM control strategies, FOC and DTC, are investigated and compared in terms of control performance through comprehensive simulation studies and the results demonstrate that DTC has better dynamic performance. Conventional DTC contributes to higher torque ripple in the PMSM due to the limited switching frequency in a conventional semiconductor-based motor drive, which inevitably deteriorates the drive performance. Therefore, this thesis aims to reduce the torque ripple in the DTC based PMSM drive by using the new generation wide bandgap switching devices. More specifically, DTC is improved by using the optimized space vector pulse width modulation strategy and a higher switching frequency contributed by the GaN based motor drive. Finally, the proposed DTC-SVM based PMSM control strategy is implemented on the digital signal processor (DSP) and evaluated on the laboratory GaN based PMSM drive. Both the simulation and experimental results show that the proposed improvement in the DTC can further improve the PMSM drive performance