Development of Faster SMA Actuators

Large cycle time, resulted from slow cooling, is the core hindrance to the wide spread applications of shape memory alloys (SMAs) as actuators. This chapter discusses a novel cooling technique to decrease the cycle time of SMAs. Under this technique, the SMA actuator of 0.15 mm diameter was run through a grease-filled Polytetrafluoroethylene (PTFE) tube of 0.5 mm outside diameter. Later, same tests were repeated with oil filled PTFE tube. The test results conducted in ambient air were used as standard for comparison. The actuation current in ambient air was set at 210, 310 and 410 mA. While testing with heat sink, i.e. grease and oil, the SMA was heated with 210, 310, 410, 500, 615 and 720 mA currents for 1 and 2 seconds, whereas the SMA was heated for 1 second only with 810 mA current. It was found that the grease cooling reduced the cooling time up to 30% and oil cooling by 20%, as compared to the ambient air-cooling time. However, the grease-cooled actuators had shown less strain, and their response was non-linear at many instances. Heat loss to the sinks resulted to more power consumption than that in ambient air cooling for equivalent amount of strain

Computer- and robot-assisted Medical Intervention

Medical robotics includes assistive devices used by the physician in order to make his/her diagnostic or therapeutic practices easier and more efficient. This chapter focuses on such systems. It introduces the general field of Computer-Assisted Medical Interventions, its aims, its different components and describes the place of robots in that context. The evolutions in terms of general design and control paradigms in the development of medical robots are presented and issues specific to that application domain are discussed. A view of existing systems, on-going developments and future trends is given. A case-study is detailed. Other types of robotic help in the medical environment (such as for assisting a handicapped person, for rehabilitation of a patient or for replacement of some damaged/suppressed limbs or organs) are out of the scope of this chapter.Comment: Handbook of Automation, Shimon Nof (Ed.) (2009) 000-00

Non-linear actuators and simulation tools for rehabilitation devices

Mención Internacional en el título de doctorRehabilitation robotics is a field of research that investigates the applications of robotics in motor function therapy for recovering the motor control and motor capability. In general, this type of rehabilitation has been found effective in therapy for persons suffering motor disorders, especially due to stroke or spinal cord injuries. This type of devices generally are well tolerated by the patients also being a motivation in rehabilitation therapy. In the last years the rehabilitation robotics has become more popular, capturing the attention at various research centers. They focused on the development more effective devices in rehabilitation therapy, with a higher acceptance factor of patients tacking into account: the financial cost, weight and comfort of the device. Among the rehabilitation devices, an important category is represented by the rehabilitation exoskeletons, which in addition to the human skeletons help to protect and support the external human body. This became more popular between the rehabilitation devices due to the easily adapting with the dynamics of human body, possibility to use them such as wearable devices and low weight and dimensions which permit easy transportation. Nowadays, in the development of any robotic device the simulation tools play an important role due to their capacity to analyse the expected performance of the system designed prior to manufacture. In the development of the rehabilitation devices, the biomechanical software which is capable to simulate the behaviour interaction between the human body and the robotics devices, play an important role. This helps to choose suitable actuators for the rehabilitation device, to evaluate possible mechanical designs, and to analyse the necessary controls algorithms before being tested in real systems. This thesis presents a research proposing an alternative solution for the current systems of actuation on the exoskeletons for robotic rehabilitation. The proposed solution, has a direct impact, improving issues like device weight, noise, fabrication costs, size an patient comfort. In order to reach the desired results, a biomechanical software based on Biomechanics of Bodies (BoB) simulator where the behaviour of the human body and the rehabilitation device with his actuators can be analysed, was developed. In the context of the main objective of this research, a series of actuators have been analysed, including solutions between the non-linear actuation systems. Between these systems, two solutions have been analysed in detail: ultrasonic motors and Shape Memory Alloy material. Due to the force - weight characteristics of each device (in simulation with the human body), the Shape Memory Alloy material was chosen as principal actuator candidate for rehabilitation devices. The proposed control algorithm for the actuators based on Shape Memory Alloy, was tested over various configurations of actuators design and analysed in terms of energy eficiency, cooling deformation and movement. For the bioinspirated movements, such as the muscular group's biceps-triceps, a control algorithm capable to control two Shape Memory Alloy based actuators in antagonistic movement, has been developed. A segmented exoskeleton based on Shape Memory Alloy actuators for the upper limb evaluation and rehabilitation therapy was proposed to demosntrate the eligibility of the actuation system. This is divided in individual rehabilitation devices for the shoulder, elbow and wrist. The results of this research was tested and validated in the real elbow exoskeleton with two degrees of freedom developed during this thesis.Programa Oficial de Doctorado en Ingeniería Eléctrica, Electrónica y AutomáticaPresidente: Eduardo Rocón de Lima.- Secretario: Concepción Alicia Monje Micharet.- Vocal: Martin Stoele

Remote-controlled ambidextrous robot hand actuated by pneumatic muscles: from feasibility study to design and control algorithms

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University LondonThis thesis relates to the development of the Ambidextrous Robot Hand engineered in Brunel University. Assigned to a robotic hand, the ambidextrous feature means that two different behaviours are accessible from a single robot hand, because of its fingers architecture which permits them to bend in both ways. On one hand, the robotic device can therefore behave as a right hand whereas, on another hand, it can behave as a left hand. The main contribution of this project is its ambidextrous feature, totally unique in robotics area. Moreover, the Ambidextrous Robot Hand is actuated by pneumatic artificial muscles (PAMs), which are not commonly used to drive robot hands. The type of the actuators consequently adds more originality to the project. The primary challenge is to reach an ambidextrous behaviour using PAMs designed to actuate non-ambidextrous robot hands. Thus, a feasibility study is carried out for this purpose. Investigating a number of mechanical possibilities, an ambidextrous design is reached with features almost identical for its right and left sides. A testbench is thereafter designed to investigate this possibility even further to design ambidextrous fingers using 3D printing and an asymmetrical tendons routing engineered to reduce the number of actuators. The Ambidextrous Robot Hand is connected to a remote control interface accessible from its website, which provides video streaming as feedback, to be eventually used as an online rehabilitation device. The secondary main challenge is to implement control algorithms on a robot hand with a range twice larger than others, with an asymmetrical tendons routing and actuated by nonlinear actuators. A number of control algorithms are therefore investigated to interact with the angular displacement of the fingers and the grasping abilities of the hand. Several solutions are found out, notably the implementations of a phasing plane switch control and a sliding-mode control, both specific to the architecture of the Ambidextrous Robot Hand. The implementation of these two algorithms on a robotic hand actuated by PAMs is almost as innovative as the ambidextrous design of the mechanical structure itself

The Development of a Brain Controlled Robotic Prosthetic Hand

An anthropomorphic, brain controlled, under actuated, Prosthetic hand has been designed and developed for upper extremity amputees. The hands function is based on micro servo actuation and the use of coupling links between parts of the finger. The control of a prosthetic hand is what differentiates this project from the others. It is the intent of this project to increase the sense of belonging between prosthesis and amputee by controlling the designed device by the brain of the amputee. The platform has been designed to use multiple force sensors to improve control. The project is a feasibility study and will be used to test whether a multi-functional and intuitive prosthetic hand is attainable. The control of the hand will be driven through a neural interface and controlled by a micro-board. This paper focuses on the mechanical design of the hand and the processes used to control the hand using signals emitted from the brain, to increase the sense of belonging between the amputee and prosthetic device. The hand has been developed as a foundation for future research into brain controlled prosthetics at the University of Waikato

Advanced Mobile Robotics: Volume 3

Mobile robotics is a challenging field with great potential. It covers disciplines including electrical engineering, mechanical engineering, computer science, cognitive science, and social science. It is essential to the design of automated robots, in combination with artificial intelligence, vision, and sensor technologies. Mobile robots are widely used for surveillance, guidance, transportation and entertainment tasks, as well as medical applications. This Special Issue intends to concentrate on recent developments concerning mobile robots and the research surrounding them to enhance studies on the fundamental problems observed in the robots. Various multidisciplinary approaches and integrative contributions including navigation, learning and adaptation, networked system, biologically inspired robots and cognitive methods are welcome contributions to this Special Issue, both from a research and an application perspective

Soft Biomimetic Finger with Tactile Sensing and Sensory Feedback Capabilities

The compliant nature of soft fingers allows for safe and dexterous manipulation of objects by humans in an unstructured environment. A soft prosthetic finger design with tactile sensing capabilities for texture discrimination and subsequent sensory stimulation has the potential to create a more natural experience for an amputee. In this work, a pneumatically actuated soft biomimetic finger is integrated with a textile neuromorphic tactile sensor array for a texture discrimination task. The tactile sensor outputs were converted into neuromorphic spike trains, which emulate the firing pattern of biological mechanoreceptors. Spike-based features from each taxel compressed the information and were then used as inputs for the support vector machine (SVM) classifier to differentiate the textures. Our soft biomimetic finger with neuromorphic encoding was able to achieve an average overall classification accuracy of 99.57% over sixteen independent parameters when tested on thirteen standardized textured surfaces. The sixteen parameters were the combination of four angles of flexion of the soft finger and four speeds of palpation. To aid in the perception of more natural objects and their manipulation, subjects were provided with transcutaneous electrical nerve stimulation (TENS) to convey a subset of four textures with varied textural information. Three able-bodied subjects successfully distinguished two or three textures with the applied stimuli. This work paves the way for a more human-like prosthesis through a soft biomimetic finger with texture discrimination capabilities using neuromorphic techniques that provides sensory feedback; furthermore, texture feedback has the potential to enhance the user experience when interacting with their surroundings. Additionally, this work showed that an inexpensive, soft biomimetic finger combined with a flexible tactile sensor array can potentially help users perceive their environment better

Rehabilitation Engineering

Population ageing has major consequences and implications in all areas of our daily life as well as other important aspects, such as economic growth, savings, investment and consumption, labour markets, pensions, property and care from one generation to another. Additionally, health and related care, family composition and life-style, housing and migration are also affected. Given the rapid increase in the aging of the population and the further increase that is expected in the coming years, an important problem that has to be faced is the corresponding increase in chronic illness, disabilities, and loss of functional independence endemic to the elderly (WHO 2008). For this reason, novel methods of rehabilitation and care management are urgently needed. This book covers many rehabilitation support systems and robots developed for upper limbs, lower limbs as well as visually impaired condition. Other than upper limbs, the lower limb research works are also discussed like motorized foot rest for electric powered wheelchair and standing assistance device