Locomotion Control of Hexapod Walking Robot with Four Degrees of Freedom per Leg

V této práci představujeme nového šestinohého robota jménem HAntR, kterého jsme vytvořili dle potřeb Laboratoře výpočetní robotiky Centra umělé inteligence fakulty Elektrotechnické Českého vysokého učení technického v Praze. Jeho hlavním účelem jest vylepšit schopnosti pohybu v těžkém terénu původního robotu přidáním čtvrtého stupně volnosti každé noze. Na základě nově navržené nohy jsme také přepracovali celé tělo robotu tak, aby splnilo i další požadavky, jako například menší rozměry, či možnost osazení alespoň šesti Lithium-Iontovými monočlánky. V práci pečlivě popisujeme motivace a úvahy, které nás k výslednému návrhu vedly. Uvádíme řešení přímé i inverzní kinematické úlohy řešené pomocí podmínky na ideální orientaci konce nohy a uvažující i důležité kinematické singularity. Navržený robot byl vyzkoušen v několika experimentech, při kterých byl použit námi navržený řídicí systém napsaný v jazyce C++. Ukázalo se, že HAntR vydrží díky zvýšené energetické hustotě a lepšímu rozkladu sil v končetinách autonomně fungovat přes hodinu. Robot je také schopen jít rychlostí až 0.42m/s, což předčí mnohé srovnatelné roboty. Při experimentu, kdy robot stál na nakloněné rovině, bylo prokázáno zlepšení oproti předchozímu robotu. A také jsme dle pokynů této práce potvrdili, že i HAntR je schopen adaptivní chůze spoléhající pouze na poziční zpětnou vazbu.In this thesis a novel six-legged robot called HAntR is presented. The robot was developed according to needs of the Robotics Laboratory, at the Artificial Intelligent Center, Faculty of Electrical Engineering, Czech Technical University in Prague. Its main purpose is enhancing rough-terrain movement capabilities by upgrading a former design by adding fourth degree of freedom to each leg. We also revised robot torso to fit new leg design and incorporate other requirements such as smaller dimensions with space for at least six Lithium-Ion cells. We thoroughly describe motivations and considerations that led us to the presented particular solution. Further, the solutions of forward and inverse kinematic tasks with partial orientation constraint and important singularities avoidance are presented. The proposed design has been evaluated in several experimental deployments, which utilised developed software controller written in C++. Endurance tests showed, that HAntR is able to remotely operate for over an hour thanks to increased energy density. Maximal speed test resulted to 0.42m/s during tripod gait, which outpaces most of the comparable robotic platforms. Experiment where HAntR stood on platform with varying inclination showed qualitative improvement against former robot. Finally, in accord with the thesis assignment, we proved that HAntR is able to perform walking with adaptive gait using positional feedback only

Decomposition and measurement optimization in electrical power systems state estimation

Imperial Users onl

Postprocesamiento CAM-ROBOTICA orientado al prototipado y mecanizado en células robotizadas complejas

The main interest of this thesis consists of the study and implementation of postprocessors to adapt the toolpath generated by a Computer Aided Manufacturing (CAM) system to a complex robotic workcell of eight joints, devoted to the rapid prototyping of 3D CAD-defined products. It consists of a 6R industrial manipulator mounted on a linear track and synchronized with a rotary table. To accomplish this main objective, previous work is required. Each task carried out entails a methodology, objective and partial results that complement each other, namely: - It is described the architecture of the workcell in depth, at both displacement and joint-rate levels, for both direct and inverse resolutions. The conditioning of the Jacobian matrix is described as kinetostatic performance index to evaluate the vicinity to singular postures. These ones are analysed from a geometric point of view. - Prior to any machining, the additional external joints require a calibration done in situ, usually in an industrial environment. A novel Non-contact Planar Constraint Calibration method is developed to estimate the external joints configuration parameters by means of a laser displacement sensor. - A first control is originally done by means of a fuzzy inference engine at the displacement level, which is integrated within the postprocessor of the CAM software. - Several Redundancy Resolution Schemes (RRS) at the joint-rate level are compared for the configuration of the postprocessor, dealing not only with the additional joints (intrinsic redundancy) but also with the redundancy due to the symmetry on the milling tool (functional redundancy). - The use of these schemes is optimized by adjusting two performance criterion vectors related to both singularity avoidance and maintenance of a preferred reference posture, as secondary tasks to be done during the path tracking. Two innovative fuzzy inference engines actively adjust the weight of each joint in these tasks.Andrés De La Esperanza, FJ. (2011). Postprocesamiento CAM-ROBOTICA orientado al prototipado y mecanizado en células robotizadas complejas [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/10627Palanci

Precision Control of a Sensorless Brushless Direct Current Motor System

Sensorless control strategies were first suggested well over a decade ago with the aim of reducing the size, weight and unit cost of electrically actuated servo systems. The resulting algorithms have been successfully applied to the induction and synchronous motor families in applications where control of armature speeds above approximately one hundred revolutions per minute is desired. However, sensorless position control remains problematic. This thesis provides an in depth investigation into sensorless motor control strategies for high precision motion control applications. Specifically, methods of achieving control of position and very low speed thresholds are investigated. The developed grey box identification techniques are shown to perform better than their traditional white or black box counterparts. Further, fuzzy model based sliding mode control is implemented and results demonstrate its improved robustness to certain classes of disturbance. Attempts to reject uncertainty within the developed models using the sliding mode are discussed. Novel controllers, which enhance the performance of the sliding mode are presented. Finally, algorithms that achieve control without a primary feedback sensor are successfully demonstrated. Sensorless position control is achieved with resolutions equivalent to those of existing stepper motor technology. The successful control of armature speeds below sixty revolutions per minute is achieved and problems typically associated with motor starting are circumvented.Research Instruments Ltd

Real-time flutter identification

The techniques and a FORTRAN 77 MOdal Parameter IDentification (MOPID) computer program developed for identification of the frequencies and damping ratios of multiple flutter modes in real time are documented. Physically meaningful model parameterization was combined with state of the art recursive identification techniques and applied to the problem of real time flutter mode monitoring. The performance of the algorithm in terms of convergence speed and parameter estimation error is demonstrated for several simulated data cases, and the results of actual flight data analysis from two different vehicles are presented. It is indicated that the algorithm is capable of real time monitoring of aircraft flutter characteristics with a high degree of reliability

Adaptive Baseband Pro cessing and Configurable Hardware for Wireless Communication

The world of information is literally at one’s fingertips, allowing access to previously unimaginable amounts of data, thanks to advances in wireless communication. The growing demand for high speed data has necessitated theuse of wider bandwidths, and wireless technologies such as Multiple-InputMultiple-Output (MIMO) have been adopted to increase spectral efficiency.These advanced communication technologies require sophisticated signal processing, often leading to higher power consumption and reduced battery life.Therefore, increasing energy efficiency of baseband hardware for MIMO signal processing has become extremely vital. High Quality of Service (QoS)requirements invariably lead to a larger number of computations and a higherpower dissipation. However, recognizing the dynamic nature of the wirelesscommunication medium in which only some channel scenarios require complexsignal processing, and that not all situations call for high data rates, allowsthe use of an adaptive channel aware signal processing strategy to provide adesired QoS. Information such as interference conditions, coherence bandwidthand Signal to Noise Ratio (SNR) can be used to reduce algorithmic computations in favorable channels. Hardware circuits which run these algorithmsneed flexibility and easy reconfigurability to switch between multiple designsfor different parameters. These parameters can be used to tune the operations of different components in a receiver based on feedback from the digitalbaseband. This dissertation focuses on the optimization of digital basebandcircuitry of receivers which use feedback to trade power and performance. Aco-optimization approach, where designs are optimized starting from the algorithmic stage through the hardware architectural stage to the final circuitimplementation is adopted to realize energy efficient digital baseband hardwarefor mobile 4G devices. These concepts are also extended to the next generation5G systems where the energy efficiency of the base station is improved.This work includes six papers that examine digital circuits in MIMO wireless receivers. Several key blocks in these receiver include analog circuits thathave residual non-linearities, leading to signal intermodulation and distortion.Paper-I introduces a digital technique to detect such non-linearities and calibrate analog circuits to improve signal quality. The concept of a digital nonlinearity tuning system developed in Paper-I is implemented and demonstratedin hardware. The performance of this implementation is tested with an analogchannel select filter, and results are presented in Paper-II. MIMO systems suchas the ones used in 4G, may employ QR Decomposition (QRD) processors tosimplify the implementation of tree search based signal detectors. However,the small form factor of the mobile device increases spatial correlation, whichis detrimental to signal multiplexing. Consequently, a QRD processor capableof handling high spatial correlation is presented in Paper-III. The algorithm and hardware implementation are optimized for carrier aggregation, which increases requirements on signal processing throughput, leading to higher powerdissipation. Paper-IV presents a method to perform channel-aware processingwith a simple interpolation strategy to adaptively reduce QRD computationcount. Channel properties such as coherence bandwidth and SNR are used toreduce multiplications by 40% to 80%. These concepts are extended to usetime domain correlation properties, and a full QRD processor for 4G systemsfabricated in 28 nm FD-SOI technology is presented in Paper-V. The designis implemented with a configurable architecture and measurements show thatcircuit tuning results in a highly energy efficient processor, requiring 0.2 nJ to1.3 nJ for each QRD. Finally, these adaptive channel-aware signal processingconcepts are examined in the scope of the next generation of communicationsystems. Massive MIMO systems increase spectral efficiency by using a largenumber of antennas at the base station. Consequently, the signal processingat the base station has a high computational count. Paper-VI presents a configurable detection scheme which reduces this complexity by using techniquessuch as selective user detection and interpolation based signal processing. Hardware is optimized for resource sharing, resulting in a highly reconfigurable andenergy efficient uplink signal detector

Advanced Signal Processing Techniques Applied to Power Systems Control and Analysis

The work published in this book is related to the application of advanced signal processing in smart grids, including power quality, data management, stability and economic management in presence of renewable energy sources, energy storage systems, and electric vehicles. The distinct architecture of smart grids has prompted investigations into the use of advanced algorithms combined with signal processing methods to provide optimal results. The presented applications are focused on data management with cloud computing, power quality assessment, photovoltaic power plant control, and electrical vehicle charge stations, all supported by modern AI-based optimization methods

Proceedings of the 3rd Annual Conference on Aerospace Computational Control, volume 1

Conference topics included definition of tool requirements, advanced multibody component representation descriptions, model reduction, parallel computation, real time simulation, control design and analysis software, user interface issues, testing and verification, and applications to spacecraft, robotics, and aircraft